ASTM F1861-2016 Standard Specification for Resilient Wall Base《弹性墙基础的标准规格》.pdf
《ASTM F1861-2016 Standard Specification for Resilient Wall Base《弹性墙基础的标准规格》.pdf》由会员分享,可在线阅读,更多相关《ASTM F1861-2016 Standard Specification for Resilient Wall Base《弹性墙基础的标准规格》.pdf(7页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F1861 08 (Reapproved 2012)1F1861 16Standard Specification forResilient Wall Base1This standard is issued under the fixed designation F1861; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A n
2、umber in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1 NOTEThe word “heterogeneous” was added to 4.2.2 editorially in December 2012.1. Scope1.1 This specification covers resilient wall base. These prod
3、ucts are manufactured from rubber or thermoplastic materials, ora combination thereof. Wall base is used to provide a functional, as well as decorative border, between walls and floors. Thisspecification does not include rigid products.1.2 The values stated in inch-pound units are to be regarded as
4、the standard. The values given in parentheses are for informationonly.1.3 The following safety caveat pertains to the test methods portion, Section 12, of this specification: This standard does notpurport to address all the safety concerns, if any, associated with its use. It is the responsibility o
5、f the user of this standard toestablish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.2. Referenced Documents2.1 The following documents of the issue in effect on the date of the material purchase form a part of this specification to t
6、heextent referenced herein:2.2 ASTM Standards:2D883 Terminology Relating to PlasticsD1566 Terminology Relating to RubberD1755 Specification for Poly(Vinyl Chloride) ResinsF137 Test Method for Flexibility of Resilient Flooring Materials with Cylindrical Mandrel ApparatusF141 Terminology Relating to R
7、esilient Floor CoveringsF386 Test Method for Thickness of Resilient Flooring Materials Having Flat SurfacesF410 Test Method for Wear Layer Thickness of Resilient Floor Coverings by Optical MeasurementF925 Test Method for Resistance to Chemicals of Resilient FlooringF1515 Test Method for Measuring Li
8、ght Stability of Resilient Flooring by Color Change2.3 Other Standards:ANSI/ASQC Z1.42003Z1.42003(R2013) Sampling Procedures and Tables for Inspection by Attributes33. Terminology3.1 DefinitionsFor definitions of other terms used in this standard, see Terminology F141.4. Classification4.1 TypesWall
9、base shall be of the following types, as specified (see 5.1.2, 6.1, and 7.1).4.1.1 Type TSrubber, vulcanized thermoset.4.1.2 Type TPrubber, thermoplastic.4.1.3 Type TVvinyl, thermoplastic.4.2 GroupsWall base shall be one of the following groups, as specified (see 5.1.2, 6.2.1, and 6.2.2):1 This spec
10、ification is under the jurisdiction of ASTM Committee F06 on Resilient Floor Coverings and is the direct responsibility of Subcommittee F06.80 onSpecifications.Current edition approved Nov. 15, 2012Nov. 1, 2016. Published November 2012December 2016. Originally approved in 1998. Last previous edition
11、 approved in 2008as F186108. 08 (2012)1. DOI: 10.1520/F1861-08R12E01.10.1520/F1861-16.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary
12、page on the ASTM website.3 Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http:/www.ansi.org.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to
13、 the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyrigh
14、t ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14.2.1 Group 1solid (homogeneous).4.2.2 Group 2layered (multiple layers/heterogeneous).4.2.3 Either group may be specified with any of the types above. It is not necessary to specify group when e
15、ither is acceptable.4.3 StylesWall base shall be of the following styles as specified (see 5.1.2, 6.3, and Fig. 1):4.3.1 Style Astraight.4.3.2 Style Bcove.4.3.3 Style Cbutt-to.4.3.4 Style Dsculptured.4.4 CornersWhere specified, both inside and outside 90 factory-made corners should be specified by s
16、tyle. Corners mustmeet the same height and thickness requirements as wall base (see Section 9).NOTE 1Factory-made corners and wall base may have visual color differences due to process and material variations. Consult the manufacturer toensure color acceptability between factory-made corners and wal
17、l base prior to ordering.5. Ordering Information5.1 Purchasers shall state whether this specification is to be used, select the preferred options permitted herein, and include thefollowing information in the invitation to bid or purchase order:5.1.1 Title, number, and date of this specification,5.1.
18、2 Type, group, and style, (see Sections 4, 6, and 7),5.1.3 Factory-made corners, if required (see 4.4),5.1.4 Color (see 6.2),5.1.5 Quantity: in pieces, linear feet, or cartons,5.1.6 Height required (see 9.1),5.1.7 Thickness required (see 9.2),5.1.8 Length required (see 9.3, 9.3.1, and Section 15),5.
19、1.9 Lot information, if other than as specified in ANSI/ASQC Z1.42003,Z1.42003(R2013), (see 11.1 and 13.1),5.1.10 Sampling, if other than as specified in ANSI/ASQC Z1.42003,Z1.42003(R2013), (see 11.1),5.1.11 Statement requesting certification, if certification of compliance is required (see Section
20、14),5.1.12 Packing requirements, if other than as specified (see Section 16),5.1.13 Palletization, if required,5.1.14 Marking required, if other than specified (see Section 15), and5.1.15 Other requirements.6. Materials and Manufacture6.1 MaterialsAny polymeric material or combination of polymeric m
21、aterials is acceptable if, in combination with processingchemicals, fillers, and colorants, the material can be formed into wall base, which satisfies all the requirements of this specification(see 5.1 and 7.1). Other suitable recycled polymeric material may be incorporated as a part of the total po
22、lymeric content.FIG. 1 Typical Profiles of Wall BaseF1861 1626.2 ColorThe color shall be as specified in the contract or order (see 5.1.4).NOTE 2The colors and styles that are available are indicated in individual manufacturers current catalogs. As manufactured, colors may varysomewhat in hue or sha
23、de from the catalog.NOTE 3Where color match is a concern, obtain current samples from the manufacturer to verify color acceptability.6.2.1 Solid Wall Base The color shall be uniform throughout the entire thickness of the wall base.6.2.2 Layered Wall BaseThe surface color need not extend through the
24、entire thickness of the wall base, but must extendthroughout the entire wear layer. Layered wall base shall have a minimum wear layer thickness of 0.002 in. (0.05 mm) whenmeasured in accordance with Test Method F410 and shall not delaminate under normal use.6.3 StylesThe style shall be as specified
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF18612016STANDARDSPECIFICATIONFORRESILIENTWALLBASE 弹性 墙基 标准 规格 PDF
链接地址:http://www.mydoc123.com/p-535877.html