ASTM F1853-2003 Standard Test Method for Measuring Sleeping Bag Packing Volume《测量睡袋密封量的标准试验方法》.pdf

《ASTM F1853-2003 Standard Test Method for Measuring Sleeping Bag Packing Volume《测量睡袋密封量的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM F1853-2003 Standard Test Method for Measuring Sleeping Bag Packing Volume《测量睡袋密封量的标准试验方法》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 1853 03An American National StandardStandard Test Method forMeasuring Sleeping Bag Packing Volume1This standard is issued under the fixed designation F 1853; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year o

2、f last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the quantitative volume of asleeping bag in a cylinder under a standardized load.1.2 This t

3、est method uses a physical volumetric measure-ment applicable in the laboratory or in the field.1.3 The values stated in SI units are to be regarded asstandard. The inch-pound units given in parentheses areprovided for information only.1.4 This standard does not purport to address all of thesafety c

4、oncerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Terminology2.1 Definitions:2.1.1 sleeping bag, na structure made of down, sy

5、ntheticfiberfill, shell fabrics, or other materials, or both, that isdesigned for people to use for thermal protection whensleeping (for example, outdoors, tent, cabin).3. Significance and Use3.1 This test method can be used to quantify and comparepacking volumes of sleeping bags. It defines the vol

6、umeoccupied by a sleeping bag under a standardized load (see 4.2).4. Apparatus4.1 Measuring CylinderA circularly round container,measuring in diameter 45 6 3cm(186 1 in.), suitable tocontain the sleeping bag being measured, and capable of notdeforming when the loading system is applied. See Annex A1

7、for specifications on a typical design.4.2 Loading SystemA circular plate or piston structurethat closely matches the diameter of the measuring cylinder,with weights, that provides a 6.90 6 0.07 kPa (1.00 6 0.01 psi)load. The diameter of the plate or piston structure should beslightly undersized, co

8、mpared to the measuring cylinder, toallow air to escape as the bag under test is subject to theloading force. Small ventilation holes are also acceptable toallow air to escape. See Annex A1 for specifications on atypical design.4.3 Measuring ScaleA scale accurate to 1 mm (1/16 in.)and having a capac

9、ity to measure the height of the loadingsystem in the measuring cylinder. For convenience, multiplescales can be placed around (and can be affixed to) themeasuring cylinder so opposing height readings can be takendirectly. Additionally, scale markings can be customized toread packing volume directly

10、 since the cross-sectional area ofthe cylinder is constant.5. Procedure5.1 Perform tests at ambient temperatures between 10 and25C (55 and 80F).5.2 Zip up the sleeping bag and place feet end first into themeasuring cylinder. The bag should be packed down slightly tomake its distribution in the measu

11、ring cylinder as uniform aspossible. Sleeping bags with low air permeability outer shellsmay be turned inside out to minimize the settling time(entrained air release) when the load is applied.5.3 Apply the loading system to the sleeping bag in themeasuring cylinder and allow to settle. The system is

12、 deemedsettled when the change in measured height is less that 1 mmin a 1 min interval.5.3.1 Using the typical design shown in Annex A1, place thepiston assembly into the measuring cylinder with the firstround disk contacting the surface of the bag. Stack weights ontop of the second disk of the pist

13、on assembly for a total (pistonand weights) of 114.1 kg (250.0 lb).5.4 Take two height readings to the nearest 1 mm (1/16 in.),one opposite the other, of the height of the compressed bag inthe measuring cylinder.5.4.1 Using the typical design shown in the annex, take twoheight readings, one opposite

14、 the other, at the top of the seconddisk of the piston assembly. Areas where the bag materialcreeps up past the loading system or where an air pocket formsshould not be used for the measurement. A flashlight can beheld inside the semi-transparent measuring cylinder so that thelocation of the top dis

15、k can be accurately determined. Subtractthe distance between the top disk and bottom disk (in contactwith the bag) from the measurement and use as the bag heightreading. In accordance with the piston assembly shown inAnnex A1, this dimension is 10.2 cm (4 in.).1This test method is under the jurisdic

16、tion of ASTM Committee F08 on SportsEquipment and Facilities and is the direct responsibility of Subcommittee F08.22 onCamping Softgoods.Current edition approved May 10, 2003. Published June 2003. Originallyapproved in 1998. Last previous edition approved in 1998 as F 185398.1Copyright ASTM Internat

17、ional, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.5 Replication of TestsRepeat the procedure above oneach bag, where the subject bag is completely removed andshaken for ;1 min and then repacked in the measuringcylinder for each repetition. Average the four

18、resulting heightvalues to yield the sleeping bag height measurement underload.6. Calculation6.1 Calculate the packing volume of the sleeping bag undertest using the following formula:V5h pr2! (1)where:V = packing volume, m3or L, where 1000 L = 1 m3,h = height of the sleeping bag under load in the me

19、asuringcylinder, m, andr = radius of the measuring cylinder, m.7. Report7.1 State that the sleeping bag was tested as directed in thistest method (ASTM F 1853). Explain any departures from thespecified apparatus or procedure.7.2 Describe the sleeping bag that was tested and itsorientation as tested

20、(normal or turned inside out, see 5.2).7.3 Report the packing volume (V)inm3or L, where 1000L=1m3units. Report packing volume values to threesignificant figures.8. Precision and Bias8.1 PrecisionThe repeatability standard deviation hasbeen determined to be 66 % in one laboratory. The reproduc-ibilit

21、y of this test method is being determined.8.2 BiasNo information can be presented on the bias ofthe procedure for determining the packing volume because nosleeping bag having an accepted reference value is available.9. Keywords9.1 packing volume; sleeping bagANNEX(Mandatory Information)A1. DETAILED

22、DESCRIPTION OF APPARATUSA1.1 A typical packing volume measuring cylinder can bea high density polyethylene (HDPE) seamless, rotation-moldedtank with rigid walls, ;46 cm (18 in.) diameter, ;76 cm (30in.) height, and ;0.5 cm (3/16 in.) wall thickness.A1.2 A typical loading system in inch-pound units i

23、s shownfor illustration purposes in Fig. A1.1. The component parts(also in inch-pound units) are illustrated in Figs. A1.1-A1.5.These are typical examples for construction consideration thatmeet the dimensional criteria described in Section 4. Weightswith a slot width of ;2 cm (3/4 in.) and meeting

24、the NationalInstitute of Standards and Technology Class F tolerances andNIST traceability are preferred.FIG. A1.1 Typical Sleeping Bag Packing Volume Loading System, Piston StructureF1853032NOTE 1Dimensions in inches.FIG. A1.2 Loading System, Part T-1, SpacerNOTE 1Dimensions in inches.FIG. A1.3 Load

25、ing System, Part T-2, WasherNOTE 1Dimensions in inches.FIG. A1.4 Loading System, Part T-3, PistonF1853033ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that

26、 determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapprov

27、ed or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you fee

28、l that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual repr

29、ints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).NOTE 1Dimensions in inches.FIG. A1.5 Loading System, Part T-4, HandleF1853034