ASTM F1807-2007a Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing《SDR9交联聚乙烯(PEX)管利用卷制铜环金属内插件的标准规范》.pdf

《ASTM F1807-2007a Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing《SDR9交联聚乙烯(PEX)管利用卷制铜环金属内插件的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F1807-2007a Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing《SDR9交联聚乙烯(PEX)管利用卷制铜环金属内插件的标准规范》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 1807 07aAn American National StandardStandard Specification forMetal Insert Fittings Utilizing a Copper Crimp Ring for SDR9Cross-linked Polyethylene (PEX) Tubing1This standard is issued under the fixed designation F 1807; the number immediately following the designation indicates the

2、year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers metal insert fittings and

3、 coppercrimp rings for use with cross-linked polyethylene (PEX)tubing in38 ,12 ,58 ,34 , and 1 in. and14 nominal diametersthat meet the requirements for Specifications F 876 and F 877.These fittings are intended for use in 100 psi (689.5 kPa) cold-and hot-water distribution systems operating at temp

4、eraturesup to, and including, 180F (82C). The requirements formaterials, workmanship, dimensions, and markings to be usedon the fittings and rings are also included.1.2 The values stated in inch-pound units are to be regardedas the standard. The values given in parentheses are mathemati-cal conversi

5、ons to SI units which are provided for informationonly and are not considered the standard.1.3 Compliance with this specification requires that thesefittings be tested and certified to Specification F 877.1.4 This standard does not purport to address all of thesafety concerns, if any, associated wit

6、h its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2A 269 Specification for Seamless and Welded AusteniticStainless Ste

7、el Tubing for General ServiceA 276 Specification for Stainless Steel Bars and ShapesA 312/A 312M Specification for Seamless, Welded, andHeavily Cold Worked Austenitic Stainless Steel PipesB 16/B 16M Specification for Free-Cutting Brass Rod, Barand Shapes for Use in Screw MachinesB62 Specification fo

8、r Composition Bronze or Ounce MetalCastingsB75 Specification for Seamless Copper TubeB88 Specification for Seamless Copper Water TubeB 140/B 140M Specification for Copper-Zinc-Lead (RedBrass or Hardware Bronze) Rod, Bar, and ShapesB 283 Specification for Copper and Copper-Alloy Die Forg-ings (Hot-Pr

9、essed)B 584 Specification for Copper Alloy Sand Castings forGeneral ApplicationsD 1600 Terminology for Abbreviated Terms Relating toPlasticsD 2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsE18 Test Methods for Rockwell Hardness of MetallicMaterialsF 412 Terminology Re

10、lating to Plastic Piping SystemsF 876 Specification for Crosslinked Polyethylene (PEX)TubingF 877 Specification for Crosslinked Polyethylene (PEX)Plastic Hot- and Cold-Water Distribution Systems2.2 ASME Standards:3B1.20.1 Pipe Threads General Purpose (Inch)B16.18 Cast Copper Alloy Solder Joint Press

11、ure FittingsB16.22 Wrought Copper and Copper Alloy Solder JointPressure Fittings2.3 Manufacturers Standardization Society Standard:4SP-104 Wrought Copper Solder Joint Pressure Fittings2.4 NSF International Standard:5Standard No. 14 for Plastic Piping Components and RelatedMaterialsStandard No. 61 fo

12、r Drinking Water System Components-Health Effects2.5 EN Standards6EN 12164 Copper and CopperAlloys-Rod for Free Machin-ing Purposes1This standard is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.Current editi

13、on approved Aug. 1, 2007. Published August 2007. Originallyapproved in 1997. Last previous edition approved in 2007 as F 1807 07.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume informati

14、on, refer to the standards Document Summary page onthe ASTM website.3Available from American Society of Mechanical Engineers (ASME), ASMEInternational Headquarters, Three Park Ave., New York, NY 10016-5990.4Available from Manufacturers Standardization Society of the Valve and FittingsIndustry (MSS),

15、 127 Park St., NE, Vienna, VA 22180-4602.5Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., AnnArbor, MI 48113-0140.6Available from European Committee for Standardization (CEN), 36 rue deStassart, B-1050, Brussels, Belgium, http:/www.cenorm.be.1Copyright ASTM International, 100

16、Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.EN 1982 Copper and Copper Alloys, Ingots and Castings3. Terminology3.1 Definitions are in accordance with Terminology F 412and abbreviations are in accordance with Terminology D 1600,unless otherwise indicated.4. Classif

17、ication4.1 This specification covers one class of fittings and coppercrimp rings suitable for use with PEX tubing that meet therequirements of Specifications F 876 or F 877.5. Materials and Manufacture5.1 FittingsThe fittings shall be made from one of thefollowing metals:5.1.1 Wrought CopperWrought

18、copper fittings shall bemade from material meeting the requirements of SpecificationB75or B88for one of the following coppers: copper UNSC10200, C10300, C10800, or C12200.5.1.2 Cast Copper AlloysCast copper alloy fittings shallbe made from material meeting the requirements of Specifica-tion B 584, c

19、opper alloy UNS C84400, C83800, or C89844 orSpecification B62, copper alloy UNS C83600, or StandardEN 1982, copper alloy EN Symbol CuSn4Zn6Pb3C.5.1.3 Machined BrassMachined brass fittings shall bemade from material meeting the requirements of SpecificationB 140/B 140M copper alloy UNS C31400, or Spe

20、cificationB 16/B 16M, copper alloy UNS C36000, or StandardEN 12164, copper alloy CW614N.5.1.4 Forged BrassForged brass fittings shall be madefrom material meeting the requirements of Specification B 283,copper alloy UNS C37700 or UNS C36500.5.1.5 Stainless SteelStainless steel fittings shall be made

21、from material meeting requirements of Specification A 312/A 312M, stainless steel alloy 304, 304L, 316 or 316L, (UNSS30400, S30403, S31600 or S31603), or Specification A 269,stainless steel alloy 304, 304L, 316, 316L (UNS S30400,S30403, S31600 or S31603), or Specification A 276, Stainlesssteel alloy

22、 304, 401L, 316, or 316L (UNS S30400, S30403,S31600 or S31603)5.2 Crimp RingsCrimp rings shall be made from copperUNS C10200 or C12200, and shall be black in color. The crimprings shall have a minimum allowable hardness of 35 and amaximum allowable hardness of 45 on the Rockwell 15T scalewhen measur

23、ed according to Test Methods E18.6. General Requirements6.1 The following sections of Specification F 877 constitutea part of this specification.6.1.1 Requirements,6.1.2 Test Methods, and6.1.3 Retest and Rejection.6.2 In addition, when a section with a title identical to thatreferenced in 6.1 appear

24、s in this specification, it containsadditional requirements that supplement those appearing inSpecification F 877.6.3 DimensionsAny randomly selected fitting or fittings,and crimp ring or crimp rings, shall be used to determinedimensions. Measurements shall be made in accordance withTest Method D 21

25、22, except when determining diameters,which is done by making measurements at four locationsspaced approximately 45 apart around the circumference.Inspection and gauging of solder joint ends shall be inaccordance with ASME B16.18, ASME B16.22, or MSSSP-104.6.4 GeneralAll performance tests shall be p

26、erformed onassemblies of fittings, crimp rings, and PEX tubing. Fittingsand crimp rings shall meet the material and dimensionalrequirements of this specification. PEX tubing shall meet therequirements of Specifications F 876 or F 877. Assembly oftest specimens shall be in accordance with 9.1.1. Use

27、separatesets of assemblies for each performance test requirement.7. Dimensions7.1 Dimensions and TolerancesThe dimensions and tol-erances of fittings and crimp rings shall be as shown in Fig. 1,Fig. 2, Fig. 3, and Fig. 4, when measured in accordance with6.3.7.1.1 AlignmentThe maximum angular variati

28、on of anyopening shall not exceed 1 off the true centerline axis.7.1.2 Fittings with Solder Joint EndsSolder joint endsshall be in accordance with ASME B16.22, ASME B16.18,orMSS SP-104.7.1.3 Tapered Threaded EndsFitting threads shall beright-hand conforming to ASME B1.20.1. They shall be taperthread

29、s (NPT).8. Workmanship, Finish, and Appearance8.1 The sealing surfaces of the insert shall be smooth andfree of foreign material. Fitting walls shall be free of cracks,holes, blisters, voids, foreign inclusions, or other defects thatare visible to the unaided eye and affect the wall integrity.9. Ass

30、embly9.1 Crimp JointsInsert fittings shall be joined to PEXtubing by the compression of a copper crimp ring around theouter circumference of the tubing, forcing the tubing materialinto annular spaces formed by ribs on the fitting. Insert fittingsand crimp rings shall meet the dimensional and materia

31、lrequirements of this standard. PEX tubing shall meet therequirements of Specifications F 876 or F 877. The dimensionsand out-of-roundness of the crimp ring, after it has beencrimped, shall be in accordance with Table 1.9.1.1 Crimping ProcedureThe crimping procedure shallbe as follows: slide the cri

32、mp ring onto the tubing, insert theribbed end of the fitting into the end of the tubing until thetubing contacts the shoulder of the fitting or tube stop. Thecrimp ring shall then be positioned on the tubing so the edge ofthe crimp ring is18 to14 in. (3.2 to 6.4 mm) from the end ofthe tube. The jaws

33、 of the crimping tool shall be centered overthe crimp ring and the tool shall be held so that the crimpingjaws are approximately perpendicular to the axis of the barb.The jaws of the crimping tool shall be closed around the crimpring, compressing the crimp ring onto the tubing. The crimpring shall n

34、ot be crimped more than once. Each crimp shall bechecked to determine conformance to the after-crimped dimen-sional requirements of Table 1 .F 1807 07a2SizeAOutsideDiameterof RibABMinimumIDDDistance toFirst RibBLMinimumInsertLengthAHMinimumRibHeightNumber ofRibsCWRibDWidthGRib SpacingTypicalT1Minimu

35、mWallET2MinimumWallERMinimumRadiusSMinimumAverageDiameterFMaximumFlash andMismatch,Total onCrest Di-ameterG,H38 in. 0.345 6 0.004 0.230 0.1800.224 0.625 0.013 2 0.030.05 0.1200.145 0.025 0.025 0.02 0.369 0.00512 in. 0.471 6 0.004 0.350 0.1800.224 0.625 0.013 2 0.030.05 0.1200.145 0.028 0.028 0.02 0.

36、495 0.00558 0.570 6 0.004 0.451 0.1800.224 0.625 0.013 2 0.030.05 0.1200.145 0.032 0.032 0.02 0.595 0.00534 in. 0.667 6 0.004 0.530 0.1800.224 0.625 0.013 2 0.030.05 0.1200.145 0.037 0.032 0.02 0.691 0.0051 in. 0.856 6 0.004 0.710 0.1800.224 0.795 0.015 3 0.030.05 0.1200.145 0.041 0.035 0.02 0.880 0

37、.005114 in. 1.045 6 0.004 0.870 0.130 mini-mum0.940 0.020 3 minimum 0.030.05 0.1200.145 0.045 0.041 0.02 1.069 0.005AMeasured from shoulder of rib to tube stop.BFitting shall be designed with sufficient overall dimensions to allow proper use of crimp tool without interference with previously complet

38、ed crimps on the same fitting.CLead chamfer area is not considered a rib.DRib sides may be angled.EApplies to entire fitting, not just insert area.FThe raised area serves as a tube stop for wrought copper fittings that do not have a shoulder.GThe maximum flash and mismatch at the root diameter betwe

39、en the ribs may not exceed 30 % of the rib height.HThe total flash and mismatch is assumed to be the difference between the dimensions X and Y (see Fig. 2). These dimensions may be measured with appropriatecalipers or micrometers. See Fig. 3 for a graphic definition of flash and mismatch created by

40、imperfection in die half interfaces.FIG. 1 Fitting Insert Dimensions and TolerancesFIG. 2 Flash and Mismatch Created by Imperfection in Die HalfInterfacesFIG. 3 Total Flash and MismatchF 1807 07a310. Product Marking10.1 Quality of MarkingThe marking shall be applied tothe fittings in such a manner t

41、hat it remains legible afterinstallation and inspection.10.2 Content of Marking:10.2.1 Marking on fittings shall include manufacturersname or trademark, or some other identifying mark, and if sizepermits, PEX or the ASTM standard number, or both.10.2.1.1 Where recessed marking is used on fittings, c

42、areshall be taken to see that the marking shall not cause cracks orreduce the wall thickness below the minimum specified.10.2.2 Marking on packaging shall include manufacturersname, fitting size, and ASTM F 1807.10.2.3 Marking on crimp rings shall include manufacturerstrademark, or some other identi

43、fying mark, and ASTM F1807.11. Quality Assurance11.1 When the product or product packing is marked withthe ASTM designation F 1807, the manufacturer affirms thatthe product was manufactured, inspected, sampled, and testedin accordance with this specification, and has been found tomeet its requiremen

44、ts.12. Keywords12.1 cold and hot water distribution; copper crimp rings;cross-linked polyethylene; metal insert fittings; PEXSizeAAverageOutside DiameterA,BBCWidthWall ThicknessBAverage WallC,D38 in. 0.630 6 0.003 0.058 6 0.0035 6 0.002 0.325 6 0.02012 in. 0.750 6 0.003 0.056 6 0.0035 6 0.002 0.325

45、6 0.02058 in. 0.875 6 0.003 0.054 6 0.0035 6 0.002 0.325 6 0.02034 in. 1.000 6 0.003 0.056 6 0.0035 6 0.002 0.325 6 0.0201 in. 1.250 6 0.003 0.049 6 0.0035 6 0.002 0.365 6 0.020114 in. 1.500 6 0.003 0.056 6 0.035 6 0.002 0.550 6 0.020AAll dimensions shall be measured with appropriate micrometers, su

46、ch as pin or ball micrometers for wall and outside diameter micrometers with flat anvils or verniercalipers shall be used to measure outside diameters and width of rings.BThe average measurement is obtained from measurements taken in at least two different circumferential positions which are equally

47、 spaced around the circumference.CThe average wall measurement is obtained from measurements taken in eight different positions which are equally spaced around the circumference.DThe maximum out-of-roundness of the crimp ring shall not inhibit assembly with the fitting and tubing. The crimp ring dim

48、ensions after crimping shall comply with Table1.FIG. 4 Copper Crimp Ring Dimensions Before CrimpingA ,B,C,DTABLE 1 Crimp Ring Dimensions After Crimping on Tube/FittingAssemblyNominal Tube SizeInsert End, in.Final Crimped OutsideDiameterA,BMinimum,in. (mm)Maximum, in. (mm)38 0.580 (14.7) 0.595 (15.1)

49、12 0.700 (17.8) 0.715 (18.2)58 0.815 (20.7) 0.830 (21.1)34 0.945 (24.0) 0.960 (24.4)1 1.175 (29.8) 1.190 (30.2)AFor all diameters except for the area of scoring caused by the crimping tool.BThe maximum out-of-roundness as measured by the difference between theminimum crimped outside diameter and the maximum crimped outside diametershall not exceed 0.006 in. (0.150 mm).F 1807 07a4SUPPLEMENTARY REQUIREMENTSThis requirement applies whenever a regulatory authority or user calls for product to be used toconvey, or be in c