ASTM F1667-2017 Standard Specification for Driven Fasteners Nails Spikes and Staples《楔入式紧固件的标准规格 钉子 长钉和u形钉》.pdf
《ASTM F1667-2017 Standard Specification for Driven Fasteners Nails Spikes and Staples《楔入式紧固件的标准规格 钉子 长钉和u形钉》.pdf》由会员分享,可在线阅读,更多相关《ASTM F1667-2017 Standard Specification for Driven Fasteners Nails Spikes and Staples《楔入式紧固件的标准规格 钉子 长钉和u形钉》.pdf(54页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F1667 15F1667 17Standard Specification forDriven Fasteners: Nails, Spikes, and Staples1This standard is issued under the fixed designation F1667; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revisio
2、n. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.The Commercial and Government Entity (Cage) Code for AST
3、M: 81346.1. Scope*1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1.NOTE 1Fastener ductility information is presented in Table 2 and dimensional information in Tables 365.1.2 Fasteners described in this specification are driven by hand tool, power
4、 tool, or mechanical device in single or multiplestrikes and are positioned by hand, tool, or machine.1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in thisstandard.1.4 Fasteners in this specification are sold in bulk (loose) form
5、 and are collated for loading into the magazine of an applicationtool. Other than as covered in Section 9, Workmanship, cohering materials (including, but not limited to, plastic, adhesive bond,paper tape, plastic strip, plastic carrier, wire, etc.) and relative orientation of collated fasteners are
6、 not within the scope of thisstandard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatorylimi
7、tations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardizationestablished in the Decision on Principles for the Development of International Standards, Guides and Recommendations issuedby the World Trade Organization Tec
8、hnical Barriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2A153/A153M Specification for Zinc Coating (Hot-Dip) on Iron and Steel HardwareA510MA510/A510M Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel(Metric)Steel, and Alloy Steel (Wi
9、thdrawn 2011)A641/A641M Specification for ZincCoated (Galvanized) Carbon Steel WireB695 Specification for Coatings of Zinc Mechanically Deposited on Iron and SteelC514 Specification for Nails for the Application of Gypsum Board3F547 Terminology of Nails for Use with Wood and Wood-Base MaterialsF592
10、Terminology of Collated and Cohered Fasteners and Their Application Tools (Withdrawn 2017)4F680 Test Methods for NailsF1575 Test Method for Determining Bending Yield Moment of Nails3. Terminology3.1 DefinitionsThe definitions used in this specification are those of common commercial acceptance and u
11、sage and alsoappear in Terminologies F547 and F592.1 This specification is under the jurisdiction ofASTM Committee F16 on Fasteners and is the direct responsibility of Subcommittee F16.05 on Driven and Other Fasteners.Current edition approved Sept. 1, 2015March 1, 2017. Published October 2015April 2
12、017. Originally approved in 1995. Last previous edition approved in 20132015 asF1667 13.F1667 15. DOI: 10.1520/F1667-15.10.1520/F1667-17.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume in
13、formation, refer to the standards Document Summary page on the ASTM website.3 Additional material and dimensional tolerance for nails used in Gypsumboard are addressed in C514.4 The last approved version of this historical standard is referenced on www.astm.org.This document is not an ASTM standard
14、and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases onl
15、y the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1TABLE 1 Classificatio
16、n and Identification IndexType Style Style Identification TableINails (NL) 1. Brads BR 32. Barrel BL 43. Boat BTH/BTL 54. Box A BXA 6Box B BXB 75. Broom BM 86. Casing CN 97. Cooler CL 108. Sinker SK 119. Corker CK 1210. Common CMA 13Common CMC 14Common CMS 15Common CMM 1611. Concrete CTS/CTM 1712. D
17、ouble-headed DH 1813. Fine FN 1914. Finishing FH 2015. Flooring FL 2116. Lath LHF 22Lath LHH 2317. Masonry MR/MRH 2418. Pallet PL 2519. Gypsum wallboard GWS 26Gypsum wallboard GWM 2720. Roofing RFA 28Roofing RFS 29Roofing RFC 30Roofing RFL 31Roofing RFR 32Roofing RFD 33Roofing RFNS/RFND 3421. Shingl
18、e SHAD/SHAS 35Shingle SHSS/SHNSB 3622. Siding SDF/SDC/SDK 3723. Slating SLA/SLC/SLS 3824. Rubber heel RH 3925. Underlayment UL 4026. Square-barbed SB 4127. Masonry drive MD 4228. Escutcheon ES 4329. Glulam rivet GR 4430. Post frame PF 4531. Roof Sheathing RingShankRSRS 46IICut nails(CN)1. Common CM
19、472. Basket BK 483. Clout CL 494. Trunk TR 505. Cobblers CB 516. Extra-iron clinching EC 527. Hob HB 53IIISpikes(SP)1. Common CM 542. Gutter GRF/GRO 553. Round RDC/RDF 564. Barge and boat BB 57IVStaples(ST)1. Fence FN 582. Poultry netting PN 593. Flat top crown FC 60Flat top crown FCC 614. Round or
20、V crown RC 625. Preformed PC 636. Electrical RE 647. Preformed hoop PH 658. Cap STC 66TABLE 1 Classification and Identification IndexType Style Style Identification TableINails (NL) 1. Brads BR 3TABLE 1 ContinuedType Style Style Identification Table2. Barrel BL 43. Box A BXA 5Box B BXB 64. Broom BM
21、75. Casing CN 86. Cooler CL 97. Sinker SK 108. Corker CK 119. AluminumCommonCMA 12CopperCommonCMC 13SteelCommonCMS 14Power-toolDrivenCommonCMP 1510. Concrete CTS/CTM 1611. Double-headed(Duplex)DH 1712. Finish FH 1813. Flooring FL 1914. Lath LHF 20Lath LHH 2115. Masonry MR/MRH 2216. Pallet PL 2317. G
22、ypsum wallboard GWS 24Gypsum wallboard GWM 2518. AluminumRoofingRFA 26SteelRoofingRFS 27Copper-CladRoofingRFC 28UmbrellaHeadRoofingRFL 29SteelReinforcedRoofingRFR 30Cap NailHand DrivenRoofingMRH/PRH 31Cap NailPower-Tool DrivenRoofingMRP/PRP 32WasheredAluminumRoofingRFNS/RFND 33WasheredSteelRoofingRF
23、E 3419. Shingle SHAD/SHAS 35Steel Shingle SHSS/SHSR 3620 Siding SDF/SDC/SDK 3721. Slating SLA/SLC/SLS 3822. Rubber heel RH 3923. Underlayment UL 4024. Square-barbed SB 4125. Masonry drive MD 4226. Escutcheon ES 4327. Glulam rivet GR 4428. Post frameRing ShankPFRS 45Roof Sheathing RingShankRSRS 4629.
24、 MetalHardwareNailsMHS/MHR 47IICut nails(CN)1. Common CM 482. Basket BK 493. Clout CL 50IIISpikes(SP)1. Common CM 51F1667 1724. Classification4.1 The fasteners and their Table 1 classification are identified as follows:NOTE 2The identification of fasteners, classified by style and type (alpha indica
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF16672017STANDARDSPECIFICATIONFORDRIVENFASTENERSNAILSSPIKESANDSTAPLES 楔入式 紧固 标准 规格 钉子 长钉 PDF

链接地址:http://www.mydoc123.com/p-535362.html