ASTM F1559-1994(2015) Standard Guide for Characteristics for Cervical Spine Immobilization Collar(s) (CSIC) 《颈椎固定颈托 (CSIC) 的标准特征指南》.pdf

《ASTM F1559-1994(2015) Standard Guide for Characteristics for Cervical Spine Immobilization Collar(s) (CSIC) 《颈椎固定颈托 (CSIC) 的标准特征指南》.pdf》由会员分享，可在线阅读，更多相关《ASTM F1559-1994(2015) Standard Guide for Characteristics for Cervical Spine Immobilization Collar(s) (CSIC) 《颈椎固定颈托 (CSIC) 的标准特征指南》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F1559 94 (Reapproved 2015)Standard Guide forCharacteristics for Cervical Spine Immobilization Collar(s)(CSIC)1This standard is issued under the fixed designation F1559; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, t

2、he year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.INTRODUCTIONThe objective of this guide is to begin to address the recognized need to support and immobilize thecompone

3、nts of the spine or spinal cord. Although this guide does not quantitatively addressperformance standards for this device, it does address the characteristics of the device(s) used toprovide support and immobilization of the components of the central nervous system for the patientsuspected of receiv

4、ing trauma to that body system.1. Scope1.1 This guide establishes minimum standards for devices,designated here as cervical spine immobilization collar(s)(CSIC), commonly referred to as cervical collars. The CSIC isused as the initial device for immobilization of the cervicalspine, of a patient by e

5、mergency medical service personnel.1.2 This guide does not identify specific degrees of limita-tion of motion achieved by placement of a CSIC on a patient.Definitive requirements for immobilization of the spine, and, inparticular, the degree of limitation associated with the use of aCSIC, have not b

6、een established in the medical literature.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulator

7、y limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2F1177 Terminology Relating to Emergency Medical Ser-vices2.2 Centers for Disease Control Standard:Guidelines for Prevention of Transmission of HIV and HBVto Healthcare and Public Safety Workers32.3 OSHA Standard:29 CFR 1910.1030 O

8、ccupational Exposure to BloodbornePathogens; Final Rule43. Terminology3.1 Definitions:3.1.1 retention systema retention system is an adjunct toor an integral part of the primary platform that allows thepatient to be securely attached to that platform used inwhatever configuration and size necessary

9、to accomplish thegoal, while still allowing reasonable and necessary access tothe patient.3.1.2 spinal immobilizationspinal immobilization shall re-fer to immobilization of the spine and its contiguous structures,the pelvis, and skull.3.1.3 spinethe spine shall include the cervical, thoracic,lumbar,

10、 and sacral vertebrae.3.2 Definitions of Terms Specific to This Standard:3.2.1 cervical spine immobilization collara device thatcan be applied and secured to a patient to support andimmobilize the cervical spine during immobilization andtransportation.1This guide is under the jurisdiction of ASTM Co

11、mmittee F30 on EmergencyMedical Services and is the direct responsibility of Subcommittee F30.01 on EMSEquipment.Current edition approved June 1, 2015. Published July 2015. Originally approvedin 1994. Last previous edition approved in 2007 as F1559 94(2007). DOI:10.1520/F1559-94R15.2For referenced A

12、STM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Centers for Disease Control spinal cord; spineASTM Internation

13、al takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their

14、own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be

15、addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards,

16、 at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 94 (2015)2