ASTM F1345-2010a(2015) Standard Specification for Zinc-5% Aluminum-Mischmetal Alloy-Coated Steel Chain-Link Fence Fabric《锌-5 %铝-含铈的稀土元素合金涂覆钢连接链环栏栅织物的标准规格》.pdf

《ASTM F1345-2010a(2015) Standard Specification for Zinc-5% Aluminum-Mischmetal Alloy-Coated Steel Chain-Link Fence Fabric《锌-5 %铝-含铈的稀土元素合金涂覆钢连接链环栏栅织物的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM F1345-2010a(2015) Standard Specification for Zinc-5% Aluminum-Mischmetal Alloy-Coated Steel Chain-Link Fence Fabric《锌-5 %铝-含铈的稀土元素合金涂覆钢连接链环栏栅织物的标准规格》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F1345 10a (Reapproved 2015)Standard Specification forZinc-5 % Aluminum-Mischmetal Alloy-Coated Steel Chain-Link Fence Fabric1This standard is issued under the fixed designation F1345; the number immediately following the designation indicates the year oforiginal adoption or, in the case

2、 of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers zinc-5 % aluminum-mischmetal (Zn-5A1-MM) alloy-coated steel chain-

3、link fencefabric, Zn-5A1-MM alloy-coated, before weaving.1.2 The values stated in inch-pound units are to be regardedas the standard.2. Referenced Documents2.1 ASTM Standards:2A90/A90M Test Method for Weight Mass of Coating onIron and Steel Articles with Zinc or Zinc-Alloy CoatingsA491 Specification

4、 for Aluminum-Coated Steel Chain-LinkFence FabricA700 Guide for Packaging, Marking, and Loading Methodsfor Steel Products for ShipmentA817 Specification for Metallic-Coated Steel Wire forChain-Link Fence Fabric and Marcelled Tension Wire2.2 Federal Standard:Fed. Std. No. 123 Marking for Shipment, Ci

5、vil Agencies32.3 Military Standards:MIL-STD-129 Marking for Shipment and Storage3MIL-STD-163 Steel Mill Products, Preparation for Ship-ment and Storage33. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 chain link fence fabrica fencing material made fromsteel wire helically wound

6、 and interwoven in such a manner asto provide a continuous mesh without knots or ties except inthe form of knuckling, or of twisting the ends of the wires toform the selvage of the fabric.3.1.2 diamond countthe number of diamond openingsfrom one edge of the fabric to the other. The diamond count ofa

7、 given fabric shall begin at the first completed diamond at oneedge and continue to the unfinished half or full opening at theother edge.3.1.3 knucklinga term used to describe the type of selvageobtained by interlocking adjacent pairs of wire ends and thenbending the wire ends back into a loop. The

8、loop shall beclosed or nearly closed to a measurement less than the diameterof the wire.3.1.4 twistinga term used to describe the type of selvageobtained by twisting adjacent pairs of wire ends together in aclose helix of 112 machine turns, which is equivalent to threefull twists, and cutting the wi

9、re ends at an angle. The wire endsbeyond the twist shall be at least14 in. (6.4 mm) long. Thistype of selvage is not used on fabric with a mesh size of lessthan 2 in. (50.8 mm).4. Ordering Information4.1 Orders for chain-link fence fabric purchased to thisspecification shall include the following in

10、formation:4.1.1 Quantity (Section 13),4.1.2 Size of mesh (Section 7),4.1.3 Size of wire (Section 8),4.1.4 Height of fabric (Section 9),4.1.5 Diamond count, if specified (Section 6),4.1.6 Type of selvage (Section 10),4.1.7 Certification if required (Section 16),4.1.8 Class of Coating (Section 11), an

11、d4.1.9 ASTM designation and year of issue.4.2 All rolls of fencing accepted by the purchaser shall bebilled on the basis of the original footage of the rolls beforesampling, unless changed by contractual arrangement.NOTE 1A typical ordering description is as follows: 25 rolls, 50 fteach, chain-link

12、fence fabric, Zn-5A1-MM alloy-coated, 2 in. mesh, 0.148in. wire, 60 in. high, knuckled both selvages, class 2 coating toSpecification F1345.1This specification is under the jurisdiction of ASTM Committee F14 on Fencesand is the direct responsibility of Subcommittee F14.40 on Chain Link Fence andWire

13、 Accessories.Current edition approved March 1, 2015. Published March 2015. Originallyapproved in 1991. Last previous edition approved in 2010 as F1345 - 10A. DOI:10.1520/F1345-10AR15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.

14、org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/www.dodssp.daps.mil.Copyright ASTM Internati

15、onal, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15. Materials5.1 The wire from which the fabric is woven shall conformto all requirements of Specification A817 for Type III coating,in the class of coating specified (Class 1 or Class 2).6. Weave6.1 The wire sh

16、all be woven throughout in the form ofapproximately uniform square mesh, having parallel sides andhorizontal and vertical diagonals of approximately uniformdimensions. The top and bottom of the fabric shall be knuckledor twisted as specified in Section 10.6.2 Typical diamond count for each standard

17、height isshown in Table 1. Other diamond counts are permissibleprovided that they are consistent within a lot. The purchaserhas the option to specify the diamond count (4.1.5).7. Size of Mesh7.1 The size of mesh shall be as indicated in Table 2.7.2 The permissible variation from the specified size o

18、fmesh shall be 618 in. (63.2 mm) for all mesh sizes except 1in., and 6116 in. (61.6 mm) for 1 in. mesh size and under.7.3 The size of mesh shall be determined by measuring theminimum clear distance between the wires forming the parallelsides of the mesh and determined as the average of tworeadings t

19、aken at right angles to each other.8. Size of Wire8.1 Chain-link fabric shall be fabricated from wire diam-eters as listed in Specification A817, with a permissiblevariation from the specified diameter of the coated wire of60.005 in. (60.13 mm).9. Height of Fabric9.1 Chain-link fabric shall be furni

20、shed in the standardheights shown in Table 2. The height of fabric shall be theoverall dimension from ends of twists or knuckles. Thepermissible variation from the specified height shall be 61 in.(625 mm) for standard selvage.10. Selvage10.1 Unless otherwise specified by the purchaser, fabricswith 2

21、- or 218-in. (50- or 54-mm) mesh, in heights 60 in. (1520mm) and under shall be knuckled at both selvages. Fabric 72in. (1830 mm) high and over shall be knuckled at one selvageand twisted at the other.10.2 The selvages of fabrics with meshes of less than 2 in.(50 mm) shall be knuckled.NOTE 2Caution:

22、 Twisted selvages for fence fabric under 72 in. (1830mm) in height are not recommended because of consumer safety consid-erations.11. Weight of Coating11.1 The weight of Zn-5A1-MM alloy coating on the fabricmay be ordered in two coating weight classes as follows, inaccordance with Specification A817

23、.11.1.1 Class 1The weight of Zn-5A1-MM alloy coatingshall not be less than 0.6 oz/ft2(183 g/m2) of uncoated wiresurface.TABLE 1 Typical Diamond CountANOTE 1Other diamond counts are permitted (see 6.2).NOTE 2For fabric heights over 144 in., see 6.2.NOTE 3Variations to knuckled or twisted selvage may

24、affect diamond count (see 6.2).Nominal Di-ameterCoatedWire, in.Size ofMesh, in.Height of Fence Fabric, in.36 42 48 60 72 84 96 108 120 1440.192 2 1012 1212 1312 1712 2012 2412 2712 3112 3412 41120.148 2 1012 1212 1312 1712 2012 2412 2712 3112 3412 41120.148 114 . . 23 29 35 41 46 52 58 700.148 20232

25、7333945536167790.120 2 1012 1212 1412 1712 2012 24120.120 134 3112 3512 3912 47120.120 202327333945536167790.113 218 912 1112 1312 1612 1912ASee Appendix X1 for SI equivalents and Fig. 1 for mesh sizes less than 1 in. (25.4 mm).TABLE 2 Sizes of Wire and MeshANOTE 1For fabrics heights over 144 in., s

26、ee 9.1.SpecifiedDiameterofCoatedWire, in.Size,CoatedWireGageSize ofMesh, in.Height of Fence Fabric, in.0.192 6 2 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.148 9 2 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.148 9 114 48,60,72,84,96,108, 120, 1440.148 9 1 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.14

27、8 912 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.120 11 2 36,42,48,60,72,84 .0.120 11 134 96,108, 120, 1440.120 11 114 48,60,72,84,96,108, 120, 1440.120 11 1 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.120 1138 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.120 1112 36, 42, 48, 60, 72, 84, 96, 108, 120,

28、1440.120 1158 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.113 1112 218 36,42,48,60,72 ASee Appendix X1 for SI equivalents. See Fig. 1 for mesh dimensions for38 in.,12in., and58 in. mesh.F1345 10a (2015)211.1.2 Class 2The weight of Zn-5A1-MM alloy coatingshall not be less than 1.0 oz/ft2(305 g/m2) of

29、uncoated wiresurface.11.2 The weight of coating shall be determined in accor-dance with Test Method A90/A90M.12. Workmanship12.1 Chain-link fence fabric shall be produced by methodsrecognized as good commercial practices. The zinc-5 %aluminium-mishcmetal before-weaving fabric shall be wovenusing pro

30、ven industry procedures to ensure a smooth consistentsurface without penetrating to the substrate, except at theselvage cut ends, see Note 3.12.2 Excessive roughness, blisters, and flaking shall benoted. These and other defects, if present to any considerableextent, shall provide a basis for rejecti

31、on.NOTE 3Rust formations on the cut ends of the wire at the fabricselvages are inherent characteristics of this material and do not warrantrejection of the fabric.13. Standard Length of Rolls13.1 The standard length of roll shall be 50 ft (15.24 m) 61 % except as otherwise agreed upon at the time of

32、 purchase.13.2 The length of roll shall be determined by unrolling aroll of fabric on a flat surface and exerting tension byappropriate means to remove all slack. The tension appliedshall not reduce the actual height of the fabric by more than116in. ft (5.3 mm/m) of height or by more than12 in. (12.

33、7 mm),whichever is less.14. Sampling and Number of Tests14.1 One roll from every 50 rolls or fraction thereof in a lotshall be taken at random as a sample for test purposes. In nocase shall less than two samples be tested, except when the lotis less than 10 rolls, only one roll shall be selected for

34、 thesample.14.2 Sample rolls selected shall be inspected for weave(Section 6), size of mesh (Section 7), diamond count (6.2), wiresize (Section 8), height of fabric (Section 9), selvage (Section10) and length (Section 13).14.3 If any specimen tested fails to meet the requirements ofthis specificatio

35、n, the roll represented by the specimen shall berejected and two additional rolls shall be inspected, both ofwhich shall meet the requirements in every respect; otherwise,the lot represented by the samples may be rejected.15. Inspection15.1 Unless otherwise specified in the purchase order orcontract

36、, the manufacturer is responsible for the performanceof all inspection and test requirements specified in this speci-fication. Except as otherwise specified in the purchase order orcontract, the manufacturer may use his own or any othersuitable facilities for the performance of the inspection and te

37、strequirements unless disapproved by the purchaser at the timethe order is placed. The purchaser shall have the right toperform any of the inspection and tests set forth in thisspecification when such inspections and tests are deemednecessary to ensure that the material conforms to prescribedrequire

38、ments.16. Certification16.1 When specified in the purchase order or contract, aproducers or suppliers certification shall be furnished to thepurchaser that the material was manufactured, sampled, tested,and inspected in accordance with this specification and hasbeen found to meet the requirements. W

39、hen specified in thepurchase order or contract a report of the test results shall befurnished.17. Packaging, Marking, and Loading17.1 Each length of chain-link fence fabric shall be tightlyrolled and firmly tied. Each roll shall carry a tag showing thetype of coating, the specified wire size, mesh s

40、ize, the specifiedlength and height of fabric in the roll, Specification A491, andthe name or mark of the manufacturer.17.2 Unless otherwise specified, packaging, marking andloading for shipment shall be in accordance with recommendedPractices A700.17.3 When specified in the contract or order, and f

41、or directprocurement by or direct shipment to the U.S. government,when Level A is specified, preservation, packaging, and pack-ing shall be in accordance with Level A requirements ofMIL-STD-163.17.4 When specified in the contract or order, and for directprocurement by or direct shipment to the U.S.

42、government,marking for shipment, in addition to the requirements specifiedMesh Size, S Height, H Width, W38 in. mesh (10 mm)34 in. (19 mm)34 in. (19 mm)12 in. mesh (13 mm)1516 in. (24 mm)1516 in. (24 mm)58 in. mesh (16 mm) 118 in. (29 mm) 118 in. (29 mm)FIG. 1 Fence Fabric Mesh Dimensions for38 in.,

43、12 in., and58 in.F1345 10a (2015)3in the contract or order, shall be in accordance with MIL-STD-129 for U.S. military agencies and in accordance with Fed. Std.No. 123 for civil agencies.18. Keywords18.1 aluminum; chain link; coated steel; fence; mischmetalAPPENDIX(Nonmandatory Information)X1. APPROX

44、IMATE SI EQUIVALENTSTABLE X1.1 Approximate SI Equivalents for Tables 1 and 2Sizes of Wire and Mesh Height of Fence Fabricin. mm in. mm0.192 4.88 36 9100.148 3.76 42 10700.120 3.05 48 12200.113 2.87 60 15201 25 72 1830114 32 84 2130134 44 96 24402 50 108 2740218 54 120 3050144 3660ASTM International

45、takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own

46、 responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be add

47、ressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at

48、 the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 10a (2015)4