ASTM F1345-1996(2003) Standard Specification for Zinc-5% Aluminum-Mischmetal Alloy-Coated Steel Chain-Link Fence Fabric《锌-5%铝-铈合金涂覆钢连接链环栏栅结构》.pdf

《ASTM F1345-1996(2003) Standard Specification for Zinc-5% Aluminum-Mischmetal Alloy-Coated Steel Chain-Link Fence Fabric《锌-5%铝-铈合金涂覆钢连接链环栏栅结构》.pdf》由会员分享，可在线阅读，更多相关《ASTM F1345-1996(2003) Standard Specification for Zinc-5% Aluminum-Mischmetal Alloy-Coated Steel Chain-Link Fence Fabric《锌-5%铝-铈合金涂覆钢连接链环栏栅结构》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 1345 96 (Reapproved 2003)Standard Specification forZinc-5 % Aluminum-Mischmetal Alloy-Coated Steel Chain-Link Fence Fabric1This standard is issued under the fixed designation F 1345; the number immediately following the designation indicates the year oforiginal adoption or, in the cas

2、e of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers zinc-5 % aluminum-mischmetal (Zn-5A1-MM) alloy-coated steel chai

3、n-link fencefabric, Zn-5A1-MM alloy-coated, before weaving.1.2 The values stated in inch-pound units are to be regardedas the standard.2. Referenced Documents2.1 ASTM Standards:A 90 Test Method for Weight of Coating on Zinc-Coated(Galvanized) Iron or Steel Articles2A 491 Specification for Aluminum-C

4、oated Steel Chain-Link Fence Fabric2A 700 Practices for Packaging, Marking and Loading Meth-ods for Steel Products for Domestic Shipment3A 817 Specification for Metallic-Coated Steel Wire forChain Link Fence Fabric22.2 Federal Standard:Fed. Std. No. 123 Marking for Shipment, Civil Agencies42.3 Milit

5、ary Standards:MIL-STD-129 Marking for Shipment and Storage4MIL-STD-163 Steel Mill Products, Preparation for Ship-ment and Storage43. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 chain link fence fabrica fencing material made fromsteel wire helically wound and interwoven in suc

6、h a manner asto provide a continuous mesh without knots or ties except inthe form of knuckling, or of twisting the ends of the wires toform the selvage of the fabric.3.1.2 diamond countthe number of diamond openingsfrom one edge of the fabric to the other. The diamond count ofa given fabric shall be

7、gin at the first completed diamond at oneedge and continue to the unfinished half or full opening at theother edge.3.1.3 knucklinga term used to describe the type of selvageobtained by interlocking adjacent pairs of wire ends and thenbending the wire ends back into a loop. The loop shall beclosed or

8、 nearly closed to a measurement less than the diameterof the wire.3.1.4 twistinga term used to describe the type of selvageobtained by twisting adjacent pairs of wire ends together in aclose helix of 112 machine turns, which is equivalent to threefull twists, and cutting the wire ends at an angle. T

9、he wire endsbeyond the twist shall be at least14 in. 6.4 mm long. Thistype of selvage is not used on fabric with a mesh size of lessthan 2 in. 50.8 mm.4. Ordering Information4.1 Orders for chain-link fence fabric purchased to thisspecification shall include the following information:4.1.1 Quantity (

10、Section 13),4.1.2 Size of mesh (Section 7),4.1.3 Size of wire (Section 8),4.1.4 Height of fabric (Section 9),4.1.5 Diamond count, if specified (Section 6),4.1.6 Type of selvage (Section 10),4.1.7 Certification if required (Section 16),4.1.8 Class of Coating (Section 11), and4.1.9 ASTM designation an

11、d year of issue.4.2 All rolls of fencing accepted by the purchaser shall bebilled on the basis of the original footage of the rolls beforesampling, unless changed by contractual arrangement.NOTE 1A typical ordering description is as follows: 25 rolls, 50 fteach, chain-link fence fabric, Zn-5A1-MM al

12、loy-coated, 2 in. mesh, 0.148in. wire, 60 in. high, knuckled both selvages, class 2 coating toSpecification F 1345.1This specification is under the jurisdiction of ASTM Committee F14 on Fencesand is the direct responsibility of Subcommittee F14.40 on Chain Link Fence andWire Accessories.Current edit

13、ion approved January 10, 2003. Published March 2003. Originallyapproved in 1991. Last previous edition approved in 1996 as F 1345 - 96.2Annual Book of ASTM Standards, Vol 01.06.3Annual Book of ASTM Standards, Vol 01.05.4Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700Robbi

14、ns Ave., Philadelphia, PA 19111-5094, Attn: NPODS.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5. Materials5.1 The wire from which the fabric is woven shall conformto all requirements of Specification A 817 for Type III coating,in

15、 the class of coating specified (Class 1 or Class 2).6. Weave6.1 The wire shall be woven throughout in the form ofapproximately uniform square mesh, having parallel sides andhorizontal and vertical diagonals of approximately uniformdimensions. The top and bottom of the fabric shall be knuckledor twi

16、sted as specified in Section 10.6.2 Typical diamond count for each standard height isshown in Table 1. Other diamond counts are permissibleprovided that they are consistent within a lot. The purchaserhas the option to specify the diamond count (4.1.5).7. Size of Mesh7.1 The size of mesh shall be as

17、indicated in Table 2.7.2 The permissible variation from the specified size ofmesh shall be 618 in. 63.2 mm for all mesh sizes except 1in., and 6116 in. 61.6 mm for 1 in. mesh size.7.3 The size of mesh shall be determined by measuring theminimum clear distance between the wires forming the parallelsi

18、des of the mesh and determined as the average of tworeadings taken at right angles to each other.8. Size of Wire8.1 Chain-link fabric shall be fabricated from wire diam-eters as listed in Specification A 817, with a permissiblevariation from the specified diameter of the coated wire of60.005 in. 60.

19、13 mm.9. Height of Fabric9.1 Chain-link fabric shall be furnished in the standardheights shown in Table 2. The height of fabric shall be theoverall dimension from ends of twists or knuckles. Thepermissible variation from the specified height shall be 61 in.625 mm for standard selvage.10. Selvage10.1

20、 Unless otherwise specified by the purchaser, fabricswith 2- or 218-in. 50- or 54-mm mesh, in heights 60 in. 1520mm and under shall be knuckled at both selvages. Fabric 72in. 1830 mm high and over shall be knuckled at one selvageand twisted at the other.10.2 The selvages of fabrics with meshes of le

21、ss than 2 in.50 mm shall be knuckled.NOTE 2Caution: Twisted selvages for fence fabric under 72 in. 1830mm in height are not recommended because of consumer safety consid-erations.11. Weight of Coating11.1 The weight of Zn-5A1-MM alloy coating on the fabricmay be ordered in two coating weight classes

22、 as follows, inaccordance with Specification A 817.11.1.1 Class 1The weight of Zn-5A1-MM alloy coatingshall not be less than 0.6 oz/ft2183 g/m2 of uncoated wiresurface.11.1.2 Class 2The weight of Zn-5A1-MM alloy coatingshall not be less than 1.0 oz/ft2305 g/m2 of uncoated wiresurface.11.2 The weight

23、 of coating shall be determined in accor-dance with Test Method A 90.12. Workmanship12.1 Chain-link fence fabric shall be produced by methodsrecognized as good commercial practices.12.2 Excessive roughness, blisters, and flaking shall benoted. These and other defects, if present to any considerablee

24、xtent, shall provide a basis for rejection.NOTE 3Rust formations on the cut ends of the wire at the fabricselvages are inherent characteristics of this material and do not warrantrejection of the fabric.13. Standard Length of Rolls13.1 The standard length of roll shall be 50 ft 15.24 m 61 % except a

25、s otherwise agreed upon at the time of purchase.TABLE 1 Typical Diamond CountANominal Di-ameterCoatedWire, in.Size ofMesh, in.Height of Fence Fabric, in.36 42 48 60 72 84 96 108 120 1440.192 2 1012 1212 1312 1712 2012 2412 2712 3112 3412 41210.148 2 1012 1212 1312 1712 2012 2412 2712 3112 3412 41120

26、.148 1 20 23 27 33 39 45 53 61 67 790.120 2 1012 1212 1412 1712 2012 24120.1200.1200.11313412182091223111227131233161239191245311253351261391267471279ASee Appendix X1 for SI equivalents.TABLE 2 Sizes of Wire and MeshASpecifiedDiameterofCoatedWire, in.Size,CoatedWireGageSize ofMesh, in.Height of Fenc

27、e Fabric, in.0.192 6 2 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.148 9 2 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.148 9 1 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.120 11 2 36, 42, 48, 60, 72, 84 .0.120 11 134 96,108, 120, 1440.120 11 1 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.113 1121218 36,4

28、2,48,60,72 ASee Appendix X1 for SI equivalents.F 1345 96 (2003)213.2 The length of roll shall be determined by unrolling aroll of fabric on a flat surface and exerting tension byappropriate means to remove all slack. The tension appliedshall not reduce the actual height of the fabric by more than116

29、in./ft 5.3 mm/m of height or by more than12 in. 12.7 mm,whichever is less.14. Sampling and Number of Tests14.1 One roll from every 50 rolls or fraction thereof in a lotshall be taken at random as a sample for test purposes. In nocase shall less than two samples be tested, except when the lotis less

30、than 10 rolls, only one roll shall be selected for thesample.14.2 Sample rolls selected shall be inspected for weave(Section 6), size of mesh (Section 7), diamond count (6.2), wiresize (Section 8), height of fabric (Section 9), selvage (Section10) and length (Section 13).14.3 If any specimen tested

31、fails to meet the requirements ofthis specification, the roll represented by the specimen shall berejected and two additional rolls shall be inspected, both ofwhich shall meet the requirements in every respect; otherwise,the lot represented by the samples may be rejected.15. Inspection15.1 Unless ot

32、herwise specified in the purchase order orcontract, the manufacturer is responsible for the performanceof all inspection and test requirements specified in this speci-fication. Except as otherwise specified in the purchase order orcontract, the manufacturer may use his own or any othersuitable facil

33、ities for the performance of the inspection and testrequirements unless disapproved by the purchaser at the timethe order is placed. The purchaser shall have the right toperform any of the inspection and tests set forth in thisspecification when such inspections and tests are deemednecessary to ensu

34、re that the material conforms to prescribedrequirements.16. Certification16.1 When specified in the purchase order or contract, aproducers or suppliers certification shall be furnished to thepurchaser that the material was manufactured, sampled, tested,and inspected in accordance with this specifica

35、tion and hasbeen found to meet the requirements. When specified in thepurchase order or contract a report of the test results shall befurnished.17. Packaging, Marking, and Loading17.1 Each length of chain-link fence fabric shall be tightlyrolled and firmly tied. Each roll shall carry a tag showing t

36、hetype of coating, the specified wire size, mesh size, the specifiedlength and height of fabric in the roll, Specification A 491, andthe name or mark of the manufacturer.17.2 Unless otherwise specified, packaging, marking andloading for shipment shall be in accordance with recommendedPractices A 700

37、.17.3 When specified in the contract or order, and for directprocurement by or direct shipment to the U.S. government,when Level A is specified, preservation, packaging, and pack-ing shall be in accordance with Level A requirements ofMIL-STD-163.17.4 When specified in the contract or order, and for

38、directprocurement by or direct shipment to the U.S. government,marking for shipment, in addition to the requirements specifiedin the contract or order, shall be in accordance with MIL-STD-129 for U.S. military agencies and in accordance with Fed. Std.No. 123 for civil agencies.APPENDIX(Nonmandatory

39、Information)X1. APPROXIMATE SI EQUIVALENTSTABLE X1.1 Approximate SI Equivalents for Tables 1 and 2Sizes of Wire and Mesh Height of Fence Fabricin. mm in. mm0.192 4.88 36 9100.148 3.76 42 10700.120 3.05 48 12200.113 2.87 60 15201 25 72 1830134 44 84 21302 50 96 2440218 54 108 2740120 3050144 3660F 13

40、45 96 (2003)3ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of suc

41、h rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for addit

42、ional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the

43、 ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F 1345 96 (2003)4