ASTM F1141 F1141M-2015 Standard Specification for Wall Coverings《墙壁覆层的标准规格》.pdf

《ASTM F1141 F1141M-2015 Standard Specification for Wall Coverings《墙壁覆层的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM F1141 F1141M-2015 Standard Specification for Wall Coverings《墙壁覆层的标准规格》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F1141 10F1141/F1141M 15Standard Specification forWall CoveringCoverings1This standard is issued under the fixed designation F1141;F1141/F1141M; the number immediately following the designation indicatesthe year of original adoption or, in the case of revision, the year of last revision.

2、 A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the performance, quality, packaging, and marking characteristics of flexible wall coveringcover-ings as a

3、finished product.products.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values givenstatedin parentheses are mathematical conversions to SI units that are provided for information only and are not considered each systemare not necessarily

4、 exact equivalents; therefore, each system shall be used independently of the other. Combining values from thetwo systems has the potential to result in non-conformance with the standard.2. Referenced Documents2.1 ASTM Standards:2F793 Classification of Wall Covering by Use Characteristics3. Terminol

5、ogy3.1 Definitions:3.1.1 wall coveringa flexible product designed to cover walls and ceilings for decorative or functional purposes, or both.3.2 Definitions of Terms Specific to This Standard:3.2.1 backing (substrate)material upon which facing (or an intermediate layer) is applied. Backing is that m

6、aterial which isadhered to the wall.3.2.2 biaspattern running off true horizontal or vertical plane.3.2.3 bolta continuous amount of packaged material containing the amount specified on the label.3.2.4 facingdecorative material which is applied to an intermediate layer or backing.3.2.5 finished prod

7、uctwall covering offered to a consumer for installation.3.2.6 intermediate layermaterial, if any, between the facing and the backing.3.2.7 lot (batch)the product from a continuous manufacturing run having the same appearance and characteristic frombeginning to end.3.2.8 pattern matchthe meeting of a

8、ll parts and colors of a pattern at the seams of adjacent strips.3.2.9 pattern repeatthe vertical distance between adjacent match points of a pattern.3.2.10 protective layerany material applied to the facing to enhance performance.3.2.11 registerthe designed meeting of all parts and colors of a patt

9、ern.3.2.12 runa unit of production which may include more than one lot.3.2.13 secondsfinished material not meeting the quality criteria in accordance with Classification required qualitycriteria.F793 and this specification.3.2.14 selvagean undecorated edge which must be trimmed away to allow for cor

10、rect pattern match or uniform continuity ofcolor.3.2.15 waste edgea decorated edge that must be trimmed away to allow for correct pattern match or uniformity of color.1 This specification is under the jurisdiction of ASTM Committee F15 on Consumer Products and is the direct responsibility of Subcomm

11、ittee F15.15 on Wallcoverings.Current edition approved April 1, 2010Dec. 1, 2015. Published May 2010January 2016. Originally approved in 1988. Last previous edition approved in 20092010 asF1141 93 (2009).F1141 10. DOI: 10.1520/F1141-10.10.1520/F1141_F1141M-15.2 For referencedASTM standards, visit th

12、eASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an

13、 indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to

14、 be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States13.2.16 Shading:3.2.16.1 color variation difference within the same lot of wall covering.3.2.16.2 luster variation difference in gloss level within th

15、e same lot of wall covering.3.2.16.3 texture variationdifference in embossing within the same lot of wall covering.3.2.17 split bolta bolt consisting of two or three separate lengths of material.4. Appearance4.1 There shall be no appreciable difference in shading except on those finished products in

16、 which natural decorativecharacteristics are being simulated. These variances must be clearly stated in writing at the point of purchase. To determine whetherthere is an appreciable difference, suspend three sequential 8-ft (2.4-m)2.4-m strips at eye level in a vertical position, as on thewall, unde

17、r illumination between 100 to 150 fc (10001000 to 1500 lx),lx, and view the strips from a distance between 4 and 8ft (1.21.2 and 2.4 m).m. An appreciable difference is one which is noticeable when one strip is compared with the others.5. Wall Preparation and Installation5.1 Basic and correct wall pr

18、eparation instructions, with particular attention to wall covering which requires special wallpreparation for its proper installation, shall be included in sample books and installation instructions.5.2 Installation instructions shall be in or with each bolt and be readily accessible to the installe

19、r. It shall be the manufacturersresponsibility to notify consumers of proper installation techniques when new products are introduced.5.3 The manufacturer shall recommend an adhesive, when necessary, and the products to be used for wall preparation.Recommendation for alternative adhesives and wall p

20、reparation products shall be included in the installation instructions.6. Physical Requirements6.1 Each finished product shall be uniform in physical properties, in accordance with Classification F793 and this specification.6.2 All facings and protective layers shall be adhered properly to backings

21、and intermediate layers and the finished product shallbe of such quality that delamination does not occur during normal installation and use.6.3 Finished products shall not chip, peel, or flake during normal installation and use. (For test methods to determine conformitywith this requirement refer t

22、o Classification F793.)6.4 There shall be no more than a 18-in. (3.5-mm)3.5-mm variance in pattern match between two 8-ft (2.4-m)2.4-m stripsat midpoint.6.5 Wall The wall covering shall be free from all surface flaws, creases, splices, scratches, tears and dirt throughout its entirelength.6.6 Wall T

23、he wall covering shall be free of wrinkles which cannot be removed in the course of normal installation.6.7 Finished The finished product shall not shrink or expand after installation when installed in accordance with themanufacturers instructions.6.8 PretrimmedAny pretrimmed material shall be trimm

24、ed so that no contrasting backing color will show at the seam when twosheets are properly installed.6.9 Pretrimmed No pretrimmed material shall show no frayed or wavy edges.6.10 All elements of the pattern shall be in register.6.11 The design shall be set at an angle of 90 to the trimmed edge.6.12 S

25、plit bolts narrow goods shall have no piece shorter than 9 ft (2.7 m)2.7 m and shall have an area at least 10 % largerthan specified on the label. Three lengths are permitted in split bolts having an area exceeding 100 ft2 (9.39.3 m2). Widecommercial goods shall have no piece shorter than 3 yd (2.7

26、m)2.7 m and one-half linear yard larger than specified on the label.6.13 The finished product shall have the necessary characteristics to adhere the product to the wall when it is installed inaccordance with the manufacturers instructions. (For test methods to determine conformity with this requirem

27、ent refer toClassification F793.)7. Inspection and Testing7.1 Manufacturers The manufacturer shall be responsible for testing and inspection in accordance with this specification andClassification F793.7.2 The introduction of new products on the market shall be preceded by thorough testing by the ma

28、nufacturer underrepresentative field conditions. Manufacturers The manufacturer shall validate laboratory quality control tests against actual fieldconditions.F1141/F1141M 1528. Rejection and Review8.1 It is acceptable for the The installer or purchaser shall be entitled to reject any wall covering

29、that fails to conform to therequirements of this specification. Rejections shall be reported to the supplier promptly in person, by phone, or in writing, or anycombination thereof.by any appropriate means. In the event the supplier is unwilling or unable to satisfy the complainant, thematter shall b

30、e referred to the manufacturer. The inspection and test procedures contained in this specification shall be used todetermine the conformance of the product to the requirements of this specification. Each manufacturer who represents a productas conforming to this specification shall be permitted to u

31、se statistically based sampling plans that are appropriate for eachparticular manufacturing process, but shall keep such essential records as are necessary to document the claim that the requirementsof this specification have been met.8.2 Any portion of the item not meeting the required quality crit

32、eria in accordance with Classification F793 and thisspecification, and thus not conforming to this specification, shall be clearly marked as seconds if packaged for resale at retail.9. Certification9.1 When specified in the purchase order or contract, a manufacturers or suppliers certification shall

33、 be furnished to thepurchaser stating that samples representing each lot of the material have been manufactured, tested, and inspected in accordancewith this specification and the requirements have been met.10. Product Marking10.1 Finished products up to 42 in. (107 cm)1.07 m in width shall be label

34、ed with the following information: pattern number,lot (batch) run number, length, width, total area of material (excluding border), supplier name and address and type of materialwhen appropriate.10.2 Finished products exceeding 42 in. (107 cm)1.07 m in width shall be labeled with the following infor

35、mation: lot (batch),run, length, width, suppliers name and address and type of material when appropriate.10.3 On a wall covering where direction of hanging is ambiguous, the manufacturer shall indicate the proper direction on eachseparate length.10.4 Bolts classified as seconds shall be prominently

36、labeled as such.10.5 Murals shall be properly numbered for sequence of sheets. If a numbering sequence is not used, a precise layout diagramshall be provided.10.6 A split bolt shall be identified as such.11. Product Packaging and Shipment11.1 The finished products shall be packaged to prevent damage

37、 in shipment.11.2 Shrink wrapping shall not be so tight that it creates product damage.11.3 Each case shall not contain more than one split bolt.12. Catalog Information12.1 Sample books shall include the length, width and square footage of each packaged bolt.12.2 Each pattern shall be identified as

38、to proper match and repeat if any.12.3 Sample bookbooks shall state that the product conforms to this specification.F1141/F1141M 15313. Keywords13.1 backing (substrate); bias; bolt; facing; finished product; intermediate layer; lot (batch); pattern match; pattern repeat;protective layer; register; r

39、un; seconds; selvage; shading and waste edge; split bolt; wall coveringASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of

40、any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn.Your comments are

41、invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not recei

42、ved a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of

43、 this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 154