ASTM F1085-2008a Standard Specification for Mattress and Box Springs for Use in Berths in Marine Vessels《海上船只铺位用床垫及包布床弹簧的标准规范》.pdf

《ASTM F1085-2008a Standard Specification for Mattress and Box Springs for Use in Berths in Marine Vessels《海上船只铺位用床垫及包布床弹簧的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F1085-2008a Standard Specification for Mattress and Box Springs for Use in Berths in Marine Vessels《海上船只铺位用床垫及包布床弹簧的标准规范》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 1085 08aAn American National StandardStandard Specification forMattress and Box Springs for Use in Berths in MarineVessels1This standard is issued under the fixed designation F 1085; the number immediately following the designation indicates the year oforiginal adoption or, in the cas

2、e of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification provides the requirements for mat-tresses and box springs that are for u

3、se in berths for officers,crew, and passengers in marine vessels. This shall be consid-ered a minimum standard.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses, in inch-pound units,are for information only.1.3 This standard is used to measure and d

4、escribe theresponse of materials, products, or assemblies to heat andflame under controlled conditions, but does not by itselfincorporate all factors required for fire-hazard or fire-riskassessment of the materials, products, or assemblies underactual fire conditions.1.4 This standard does not purpo

5、rt to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D 12

6、3 Terminology Relating to TextilesD 1424 Test Method for Tearing Strength of Fabrics byFalling-Pendulum Type (Elmendorf) ApparatusD 3574 Test Methods for Flexible Cellular MaterialsSlab,Bonded, and Molded Urethane FoamsD 3951 Practice for Commercial PackagingD 5034 Test Method for Breaking Strength

7、and Elongationof Textile Fabrics (Grab Test)D 6193 Practice for Stitches and SeamsD 6413 Test Method for Flame Resistance of Textiles (Ver-tical Test)E 162 Test Method for Surface Flammability of MaterialsUsing a Radiant Heat Energy SourceE 176 Terminology of Fire StandardsE 662 Test Method for Spec

8、ific Optical Density of SmokeGenerated by Solid MaterialsE 1354 Test Method for Heat and Visible Smoke ReleaseRates for Materials and Products Using an Oxygen Con-sumption CalorimeterE 1590 Test Method for Fire Testing of MattressesF 1566 Test Methods for Evaluation of Innersprings andBoxsprings2.2

9、ANSI Standards:3ANSI Z357.1-1981 American National Standard for Bed-ding Products and ComponentsANSI/ASQC Z1.4 Sampling Procedures and Tables for In-spection by Attributes2.3 California Bureau of Home Furnishings and ThermalInsulation Standard:CATechnical Bulletin 129, (CATB 129) Flammability TestPr

10、ocedure for Mattresses for Use in Public BuildingsOctober 199242.4 Federal Standards:Code of Federal Regulations Title 16, Vol 2, Part 16325Purchase DescriptionMattressInnerspring, Flame-Resistant, ShipboardNAVSEA 05L PD 4-02 (May2002)61This specification is under the jurisdiction of ASTM Committee

11、F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved Nov. 1, 2008. Published November 2008. Originallyapproved in 1988. Last previous edition approved in 2008 as F 1085 - 08.2For referenced ASTM standards,

12、visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New Y

13、ork, NY 10036, http:/www.ansi.org.4Available from California Bureau of Home Furnishings and Thermal Insula-tion, 3483 Orange Grove Ave., North Highlands, CA 95660.5Available from U.S. Government Printing Office Superintendent of Documents,732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401,

14、 http:/www.access.gpo.gov.6Available from Naval Sea Systems Command (NAVSEA), 1333 Isaac HullAve., SE, Washington, DC 20376, http:/www.navsea.navy.mil.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.2.5 NFPA Standard:NFPA 301 Code fo

15、r Safety to Life from Fire on MerchantVessels73. Terminology3.1 DefinitionsFor definitions of terms used in this speci-fication associated with textiles, see Terminology D 123. Fordefinitions of terms used in this specification associated withfire issues, see Terminology E 176.3.2 Definitions of Ter

16、ms Specific to This Standard:3.2.1 border, na material that forms the side panel thatsurrounds the perimeter of the mattress and defines its depth.3.2.2 box spring, na foundation for a mattress, consistingof wire spring elements mounted on a frame, generallyupholstered and covered on the top and sid

17、es with ticking, andon the bottom with a dust cover.3.2.3 box spring assembly, nan interconnection of coilsprings, border wire, and top wire assembly contained within abox spring.3.2.4 flaming droplets, nflaming molten or flaming lique-fied droplets which fall from the test specimen during the firet

18、est and continue to burn.3.2.5 flange, nstrip of material secured to the perimeter ofan upholstery panel to secure to the innerspring core.3.2.6 innerspring unit, nan interconnection of wire springelements other than mounting on a frame that forms a singleunit that can be incorporated into a mattres

19、s.3.2.7 insulator pad, none or more layers of a cushioningsystem between the upholstery and mattress core, whichconsist of foam or other cushioning or filling materials.3.2.8 mattress, nticking filled with a resilient materialused alone or in combination with other products intended orpromoted for s

20、leeping upon.3.2.9 mattress core, nthe main support system that maybe present in a mattress, such as springs, foam, or resilientfilling.3.2.10 mattress, innerspring, nany mattress containing aninnerspring unit.3.2.11 mattress, solid core, nany mattress containingpadding, but not an innerspring unit.

21、3.2.12 quilted, adjstitched with any thread or by fusionthrough the ticking and one or more layers of upholsterymaterial.3.2.13 tape edge, nseam or border edge of a mattress.3.2.14 ticking, nthe outermost layer of fabric or relatedmaterial that encloses the core and upholstery materials of amattress

22、 or mattress pad.4. Ordering Information4.1 Orders for items purchased under this specification shalldefine the following:4.1.1 MattressesQuantity, dimensional requirements, type(solid core or innerspring), and weight per each size.4.1.2 Box SpringsQuantity, dimensional requirements,and weight per e

23、ach size.4.1.3 Upholstery material selections are to be offered aschoices by the manufacturer or distributor to the purchaser. Theselection shall be of good quality suitable for commercial useand for use aboard U.S. Navy vessels.4.1.4 When first article of inspection is required, it shall bespelled

24、out in the paperwork.5. Materials and Manufacture5.1 Innerspring MattressThe essential components of aninnerspring mattress are: an innerspring core, cushioning,upholstery ticking (either quilted or with a smooth top, andpotentially including a flange), and a border. Optional compo-nents include var

25、ious insulating layers or pads, flanges, andtapes. All materials used shall meet the mechanical propertyand fire performance requirements of Table 1. All materialsused shall comply with appropriate commercial bedding indus-try standards of manufacture and durability. Any constructionof an innersprin

26、g mattress that is suitable for its intended useand that complies with the performance requirements shownherein shall be permitted to be used.5.1.1 Innerspring CoreThe innerspring core shall be con-structed from an all-wire carbon steel. The coils shall extendthe full length and width of the mattres

27、s. The coils shall bepermanently secured to provide long-term structural stability.Various core designs shall be permitted. The support propertiesof the innerspring core, in terms of firmness rating, durability,resistance to impact, firmness retention, and surface deforma-tion, shall be assessed by

28、Test Methods F 1566. The coils, orthe complete spring unit assembly, shall be given suitablethermal treatment to relieve residual stresses caused by coiling.5.1.2 Cushioning and Insulator LayersAn insulator padshall be placed over each sleeping surface of the innerspringcore to insulate the upholste

29、ry from the core. The variouscushioning layers shall be constructed of materials that meetthe performance requirements of Table 1.5.1.3 Ticking and Cover AssemblyThe cover constructionshall be suitable for the type of mattress construction used.Upholstery ticking materials shall be durable, per comm

30、onbedding industry practices. The ticking for each sleepingsurface shall be cut in one piece without fabric splices. Theticking for the mattress border shall be made of not more thantwo pieces of ticking, with the ends spliced and sewn togetherin a continuous manner leaving no gaps or voids in unifo

31、rmityand finish. The border assembly shall be secured to the top andbottom sleeping surfaces of the mattress, by automatic sewing,per common bedding industry practices.5.1.4 BorderThe ticking for the mattress border shall bemade of not more than two pieces of ticking, with the endsspliced and sewn t

32、ogether in a continuous manner leaving nogaps or voids in uniformity and finish. The border assemblyshall be secured to the top and bottom sleeping surfaces of themattress, by automatic sewing, per common bedding industrypractices.5.1.5 TapeA tape shall be permitted to be used to concealthe seams fo

33、rmed between the border, if present, and anupholstery panel. The tape shall be continuously stitched alongthe total length of each seam, with no gaps or voids betweenthe upholstery panel and border surfaces.7Available from National Fire Protection Association (NFPA), 1 BatterymarchPark, Quincy, MA 0

34、2169-7471, http:/www.nfpa.org.F 1085 08a25.1.6 Seam and StitchingThe seam and stitch types shallbe in accordance with Practice D 6193. All seams shall besecurely stitched. Seams shall not slip or pull out.5.1.7 MattressAll mattress components shall meet therequirements of Table 1, as appropriate. Th

35、e overall mattressshall meet the performance requirements of Table 2,asTABLE 1 Mattress Component RequirementsComponent Characteristic Requirement Test MethodUpholstery Ticking(and Flange, Tape, and Pocketing Materials, if used)(Notes 1 and 2)Initial FlammabilityChar Length #127 mm (5.0 in.) Test Me

36、thod D 6413After Flame #2.0 s Test Method D 6413No Flaming Droplets Test Method D 6413Flammability after 15 LaunderingsChar Length #127 mm (5.0 in.) Test Method D 6413After Flame #2.0 s Test Method D 6413No Flaming Droplets Test Method D 6413Other PropertiesTear Strength (Note 3) Warp: 1.6 kg (3.5 l

37、b) min;Filling: 1.6 kg (3.5 lb) minTest Method D 1424Breaking Strength (Note 3) Warp: 42.6 kg (94 lb) min;Filling: 26.3 kg (58 lb) minTest Method D 5034Border Ticking FlammabilityChar Length #38 mm (1.5 in.) Test Method D 6413After Flame #2.0 s Test Method D 6413No Flaming Droplets Test Method D 641

38、3DMAX50 Test Method E 662DMAXNo Flaming Droplets Test Method E 662Other PropertiesTear Strength Warp: 1.8 kg (4 lb) min;Filling: 1.8 kg (4 lb) minTest Method D 1424Breaking Strength Warp: 42.6 kg (94 lb) min;Filling: 22.7 kg (50 lb) minTest Method D 5034Cushioning and Insulator Layers FlammabilityCh

39、ar Length #127 mm (5.0 in.) Test Method D 6413After Flame #2.0 s Test Method D 6413No Flaming Droplets Test Method D 6413Flame Spread (Is)(Note 4 10 Test Method E 162DMAX(Note 4) 200 Test Method E 662DMAX(Note 4) No Flaming Droplets Test Method E 662Other PropertiesDry Heat Aging /Compression Force

40、DeflectionNo more than 20 % change incompression force deflectionTest Method D 3574,Methods C and KNOTE 1Only Molten and/or Flaming Droplets requirement applies to Tape.NOTE 2Only Initial Flammability requirements apply to Pocketing Material.NOTE 3Tear Strength and Breaking Strength apply only to Up

41、holstery Ticking.NOTE 4When materials are not identical on both sides, each side shall be tested as a different specimen.TABLE 2 Full Mattress RequirementsCharacteristics Requirement Test MethodFire Performance CharacteristicsMinimum a. Maximum Rate of Heat Release #100 kW Test Method E 1590b. Maxim

42、um Total Heat Release in first 10 min of test #25 MJ Test Method E 1590c. Maximum Mass Loss in the first 10 min of test #1.4 kg (3 lb) Test Method E 1590d. Class A Pass 16 CFR 1632Optional (US Navy Requirement) a. Maximum Rate of Heat Release #150 kW Annex A1b. Maximum Average Specific Extinction Ar

43、ea 300 m2/kg Annex A1c. No Flaming Droplets Annex A1Optional Screening Test Mass loss #15 % (based on initial mass) Annex A3Physical CharacteristicsDurability (Rollator Test) a. Firmness Rating of 330 N (75 lbf) 6 10 %, after 100 000 cycles Test Method F 1566, Section 7b. Permanent Deformation #20 %

44、 of depth Test Method F 1566, Section 7c. No Damage Test Method F 1566, Section 7Firmness Retention and Surface Deformation (Cornell Test) a. Accumulated Dimple #44.5 mm (1.75 in.) Test Method F 1566, Section 9b. Support Firmness Change #(+ 40 %) - (-15 %) Test Method F 1566, Section 9Dimensions See

45、 Section 6Weight See Section 6Visual CharacteristicsVisual Defects See section 6.5 ANSI/ASQC Z1.4F 1085 08a3discussed in Section 6. For dimensional requirements, see 6.6.5.1.7.1 Upholstery ticking, as well as any flange, tape, andpocketing materials used, shall exhibit a char length notexceeding 127

46、 mm (5.0 in.), an after flame period not exceed-ing 2.0 s, and shall not exhibit any molten or flaming droplets,or both, when tested in accordance with Test Method D 6413.The char length and after flame requirements shall not apply totape.5.1.7.2 Upholstery ticking, as well as any flange, tape, andp

47、ocketing materials used, shall exhibit a char length notexceeding 127 mm (5.0 in.), an after flame period not exceed-ing 2.0 s, and shall not exhibit any molten or flaming droplets,or both, when tested in accordance with Test Method D 6413,after having been subjected to 15 launderings. The char leng

48、thand after flame requirements shall not apply to tape.5.1.7.3 Border ticking materials shall exhibit a char lengthnot exceeding 38 mm (1.5 in.), an after flame period notexceeding 2.0 s, and shall not exhibit any molten or flamingdroplets, or both, when tested in accordance with Test MethodD 6413.

49、Border ticking materials shall also exhibit a maximumspecific optical density (DMAX) not exceeding 50, and shall notexhibit any molten or flaming droplets, or both, when tested inaccordance with Test Method E 662.5.1.7.4 Cushioning and insulator layer materials shall ex-hibit a char length not exceeding 127 mm (5.0 in.), an afterflame period not exceeding 2.0 s, and shall not exhibit anymolten or flaming droplets, or both, when tested in accordancewith Test Method D 6413. Cushioning and insulator layermaterials shall also exhibit a radiant panel