ASTM F1085-2008 Standard Specification for Mattress and Box Springs for Use in Berths in Marine Vessels.pdf

《ASTM F1085-2008 Standard Specification for Mattress and Box Springs for Use in Berths in Marine Vessels.pdf》由会员分享，可在线阅读，更多相关《ASTM F1085-2008 Standard Specification for Mattress and Box Springs for Use in Berths in Marine Vessels.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 1085 08An American National StandardStandard Specification forMattress and Box Springs for Use in Berths in MarineVessels1This standard is issued under the fixed designation F 1085; the number immediately following the designation indicates the year oforiginal adoption or, in the case

2、 of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification provides the requirements for mat-tresses and box springs that are for us

3、e in berths for officers,crew, and passengers in marine vessels. This shall be consid-ered a minimum standard.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses, in inch-pound units,are for information only.1.3 This standard is used to measure and de

4、scribe theresponse of materials, products, or assemblies to heat andflame under controlled conditions, but does not by itselfincorporate all factors required for fire-hazard or fire-riskassessment of the materials, products, or assemblies underactual fire conditions.1.4 This standard does not purpor

5、t to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D 123

6、 Terminology Relating to TextilesD 1424 Test Method for Tearing Strength of Fabrics byFalling-Pendulum Type (Elmendorf) ApparatusD 3574 Test Methods for Flexible Cellular MaterialsSlab,Bonded, and Molded Urethane FoamsD 3951 Practice for Commercial PackagingD 5034 Test Method for Breaking Strength a

7、nd Elongationof Textile Fabrics (Grab Test)D 6193 Practice for Stitches and SeamsD 6413 Test Method for Flame Resistance of Textiles (Ver-tical Test)3E 162 Test Method for Surface Flammability of MaterialsUsing a Radiant Heat Energy SourceE 176 Terminology of Fire StandardsE 662 Test Method for Spec

8、ific Optical Density of SmokeGenerated by Solid MaterialsE 1354 Test Method for Heat and Visible Smoke ReleaseRates for Materials and Products Using an Oxygen Con-sumption CalorimeterE 1590 Test Method for Fire Testing of MattressesF 1566 Test Methods for Evaluation of Innersprings andBoxsprings2.2

9、ANSI Standards:4ANSI Z357.1-1981 American National Standard for Bed-ding Products and ComponentsANSI/ASQC Z1.4 Sampling Procedures and Tables for In-spection by Attributes2.3 California Bureau of Home Furnishings and ThermalInsulation Standard:CATechnical Bulletin 129, (CATB 129) Flammability TestPr

10、ocedure for Mattresses for Use in Public BuildingsOctober 199252.4 Federal Standards:Code of Federal Regulations Title 16, Vol 2, Part 16326Purchase DescriptionMattressInnerspring, Flame-Resistant, ShipboardNAVSEA 05L PD 4-02 (May2002)71This specification is under the jurisdiction of ASTM Committee

11、F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved May 1, 2008. Published June 2008. Originallyapproved in 1988. Last previous edition approved in 2003 as F 1085 - 03a(2007).2For referenced ASTM standards

12、, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn.4Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th

13、 Floor, New York, NY 10036, http:/www.ansi.org.5Available from California Bureau of Home Furnishings and Thermal Insula-tion, 3483 Orange Grove Ave., North Highlands, CA 95660.6Available from U.S. Government Printing Office Superintendent of Documents,732 N. Capitol St., NW, Mail Stop: SDE, Washingt

14、on, DC 20401, http:/www.access.gpo.gov.7Available from Naval Sea Systems Command (NAVSEA), 1333 Isaac HullAve., SE, Washington, DC 20376, http:/www.navsea.navy.mil.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.2.5 NFPA Standard:NFP

15、A 301 Code for Safety to Life from Fire on MerchantVessels83. Terminology3.1 DefinitionsFor definitions of terms used in this speci-fication associated with textiles, see Terminology D 123. Fordefinitions of terms used in this specification associated withfire issues, see Terminology E 176.3.2 Defin

16、itions of Terms Specific to This Standard:3.2.1 border, na material that forms the side panel thatsurrounds the perimeter of the mattress and defines its depth.3.2.2 box spring, na foundation for a mattress, consistingof wire spring elements mounted on a frame, generallyupholstered and covered on th

17、e top and sides with ticking, andon the bottom with a dust cover.3.2.3 box spring assembly, nan interconnection of coilsprings, border wire, and top wire assembly contained within abox spring.3.2.4 flaming droplets, nflaming molten or flaming lique-fied droplets which fall from the test specimen dur

18、ing the firetest and continue to burn.3.2.5 flange, nstrip of material secured to the perimeter ofan upholstery panel to secure to the innerspring core.3.2.6 innerspring unit, nan interconnection of wire springelements other than mounting on a frame that forms a singleunit that can be incorporated i

19、nto a mattress.3.2.7 insulator pad, none or more layers of a cushioningsystem between the upholstery and mattress core, whichconsist of foam or other cushioning or filling materials.3.2.8 mattress, nticking filled with a resilient materialused alone or in combination with other products intended orp

20、romoted for sleeping upon.3.2.9 mattress core, nthe main support system that maybe present in a mattress, such as springs, foam, or resilientfilling.3.2.10 mattress, innerspring, nany mattress containing aninnerspring unit.3.2.11 mattress, solid core, nany mattress containingpadding, but not an inne

21、rspring unit.3.2.12 quilted, adjstitched with any thread or by fusionthrough the ticking and one or more layers of upholsterymaterial.3.2.13 tape edge, nseam or border edge of a mattress.3.2.14 ticking, nthe outermost layer of fabric or relatedmaterial that encloses the core and upholstery materials

22、 of amattress or mattress pad.4. Ordering Information4.1 Orders for items purchased under this specification shalldefine the following:4.1.1 MattressesQuantity, dimensional requirements, type(solid core or innerspring), and weight per each size.4.1.2 Box SpringsQuantity, dimensional requirements,and

23、 weight per each size.4.1.3 Upholstery material selections are to be offered aschoices by the manufacturer or distributor to the purchaser. Theselection shall be of good quality suitable for commercial useand for use aboard U.S. Navy vessels.4.1.4 When first article of inspection is required, it sha

24、ll bespelled out in the paperwork.5. Materials and Manufacture5.1 Innerspring MattressThe essential components of aninnerspring mattress are: an innerspring core, cushioning,upholstery ticking (either quilted or with a smooth top, andpotentially including a flange), and a border. Optional compo-nent

25、s include various insulating layers or pads, flanges, andtapes. All materials used shall meet the mechanical propertyand fire performance requirements of Table 1. All materialsused shall comply with appropriate commercial bedding indus-try standards of manufacture and durability. Any constructionof

26、an innerspring mattress that is suitable for its intended useand that complies with the performance requirements shownherein shall be permitted to be used.5.1.1 Innerspring CoreThe innerspring core shall be con-structed from an all-wire carbon steel. The coils shall extendthe full length and width o

27、f the mattress. The coils shall bepermanently secured to provide long-term structural stability.Various core designs shall be permitted. The support propertiesof the innerspring core, in terms of firmness rating, durability,resistance to impact, firmness retention, and surface deforma-tion, shall be

28、 assessed by Test Methods F 1566. The coils, orthe complete spring unit assembly, shall be given suitablethermal treatment to relieve residual stresses caused by coiling.5.1.2 Cushioning and Insulator LayersAn insulator padshall be placed over each sleeping surface of the innerspringcore to insulate

29、 the upholstery from the core. The variouscushioning layers shall be constructed of materials that meetthe performance requirements of Table 1.5.1.3 Ticking and Cover AssemblyThe cover constructionshall be suitable for the type of mattress construction used.Upholstery ticking materials shall be dura

30、ble, per commonbedding industry practices. The ticking for each sleepingsurface shall be cut in one piece without fabric splices. Theticking for the mattress border shall be made of not more thantwo pieces of ticking, with the ends spliced and sewn togetherin a continuous manner leaving no gaps or v

31、oids in uniformityand finish. The border assembly shall be secured to the top andbottom sleeping surfaces of the mattress, by automatic sewing,per common bedding industry practices.5.1.4 BorderThe ticking for the mattress border shall bemade of not more than two pieces of ticking, with the endssplic

32、ed and sewn together in a continuous manner leaving nogaps or voids in uniformity and finish. The border assemblyshall be secured to the top and bottom sleeping surfaces of themattress, by automatic sewing, per common bedding industrypractices.5.1.5 TapeA tape shall be permitted to be used to concea

33、lthe seams formed between the border, if present, and anupholstery panel. The tape shall be continuously stitched alongthe total length of each seam, with no gaps or voids betweenthe upholstery panel and border surfaces.8Available from National Fire Protection Association (NFPA), 1 BatterymarchPark,

34、 Quincy, MA 02169-7471, http:/www.nfpa.org.F10850825.1.6 Seam and StitchingThe seam and stitch types shallbe in accordance with Practice D 6193. All seams shall besecurely stitched. Seams shall not slip or pull out.5.1.7 MattressAll mattress components shall meet therequirements of Table 1, as appro

35、priate. The overall mattressshall meet the performance requirements of Table 2,asTABLE 1 Mattress Component RequirementsComponent Characteristic Requirement Test MethodUpholstery Ticking(and Flange, Tape, and Pocketing Materials, if used)(Notes 1 and 2)Initial FlammabilityChar Length #127 mm (5.0 in

36、.) Test Method D 6413After Flame #2.0 s Test Method D 6413No Flaming Droplets Test Method D 6413Flammability after 15 LaunderingsChar Length #127 mm (5.0 in.) Test Method D 6413After Flame #2.0 s Test Method D 6413No Flaming Droplets Test Method D 6413Other PropertiesTear Strength (Note 3) Warp: 1.6

37、 kg (3.5 lb) min;Filling: 1.6 kg (3.5 lb) minTest Method D 1424Breaking Strength (Note 3) Warp: 42.6 kg (94 lb) min;Filling: 26.3 kg (58 lb) minTest Method D 5034Border Ticking FlammabilityChar Length #38 mm (1.5 in.) Test Method D 6413After Flame #2.0 s Test Method D 6413No Flaming Droplets Test Me

38、thod D 6413DMAX50 Test Method E 662DMAXNo Flaming Droplets Test Method E 662Other PropertiesTear Strength Warp: 1.8 kg (4 lb) min;Filling: 1.8 kg (4 lb) minTest Method D 1424Breaking Strength Warp: 42.6 kg (94 lb) min;Filling: 22.7 kg (50 lb) minTest Method D 5034Cushioning and Insulator Layers Flam

39、mabilityChar Length #127 mm (5.0 in.) Test Method D 6413After Flame #2.0 s Test Method D 6413No Flaming Droplets Test Method D 6413Flame Spread (Is)(Note 4 10 Test Method E 162DMAX(Note 4) 200 Test Method E 662DMAX(Note 4) No Flaming Droplets Test Method E 662Other PropertiesDry Heat Aging /Compress

40、ion Force DeflectionNo more than 20 % change incompression force deflectionTest Method D 3574,Methods C and KNOTE 1Only Molten and/or Flaming Droplets requirement applies to Tape.NOTE 2Only Initial Flammability requirements apply to Pocketing Material.NOTE 3Tear Strength and Breaking Strength apply

41、only to Upholstery Ticking.NOTE 4When materials are not identical on both sides, each side shall be tested as a different specimen.TABLE 2 Full Mattress RequirementsCharacteristics Requirement Test MethodFire Performance CharacteristicsMinimum a. Maximum Rate of Heat Release #100 kW Test Method E 15

42、90b. Maximum Total Heat Release in first 10 min of test #25 MJ Test Method E 1590c. Maximum Mass Loss in the first 10 min of test #1.4 kg (3 lb) Test Method E 1590d. Class A Pass 16 CFR 1632Optional (US Navy Requirement) a. Maximum Rate of Heat Release #150 kW Annex A1b. Maximum Average Specific Ext

43、inction Area 300 m2/kg Annex A1c. No Flaming Droplets Annex A1Physical CharacteristicsDurability (Rollator Test) a. Firmness Rating of 330 N (75 lbf) 6 10 %, after 100 000 cycles Test Method F 1566, Section 7b. Permanent Deformation #20 % of depth Test Method F 1566, Section 7c. No Damage Test Metho

44、d F 1566, Section 7Firmness Retention and Surface Deformation (Cornell Test) a. Accumulated Dimple #44.5 mm (1.75 in.) Test Method F 1566, Section 9b. Support Firmness Change #(+ 40 %) - (-15 %) Test Method F 1566, Section 9Dimensions See Section 6Weight See Section 6Visual CharacteristicsVisual Def

45、ects See section 6.5 ANSI/ASQC Z1.4F1085083discussed in Section 6. For dimensional requirements, see 6.6.5.1.7.1 Upholstery ticking, as well as any flange, tape, andpocketing materials used, shall exhibit a char length notexceeding 127 mm (5.0 in.), an after flame period not exceed-ing 2.0 s, and sh

46、all not exhibit any molten or flaming droplets,or both, when tested in accordance with Test Method D 6413.The char length and after flame requirements shall not apply totape.5.1.7.2 Upholstery ticking, as well as any flange, tape, andpocketing materials used, shall exhibit a char length notexceeding

47、 127 mm (5.0 in.), an after flame period not exceed-ing 2.0 s, and shall not exhibit any molten or flaming droplets,or both, when tested in accordance with Test Method D 6413,after having been subjected to 15 launderings. The char lengthand after flame requirements shall not apply to tape.5.1.7.3 Bo

48、rder ticking materials shall exhibit a char lengthnot exceeding 38 mm (1.5 in.), an after flame period notexceeding 2.0 s, and shall not exhibit any molten or flamingdroplets, or both, when tested in accordance with Test MethodD 6413. Border ticking materials shall also exhibit a maximumspecific opt

49、ical density (DMAX) not exceeding 50, and shall notexhibit any molten or flaming droplets, or both, when tested inaccordance with Test Method E 662.5.1.7.4 Cushioning and insulator layer materials shall ex-hibit a char length not exceeding 127 mm (5.0 in.), an afterflame period not exceeding 2.0 s, and shall not exhibit anymolten or flaming droplets, or both, when tested in accordancewith Test Method D 6413. Cushioning and insulator layermaterials shall also exhibit a radiant panel index (Is) notexceeding 10 when tested in accordance with Test Met