ASTM F1080-1993(2013) Standard Test Method for Determining the Consistency of Viscous Liquids Using a Consistometer《采用稠度计测定粘液稠度的标准试验方法》.pdf

《ASTM F1080-1993(2013) Standard Test Method for Determining the Consistency of Viscous Liquids Using a Consistometer《采用稠度计测定粘液稠度的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM F1080-1993(2013) Standard Test Method for Determining the Consistency of Viscous Liquids Using a Consistometer《采用稠度计测定粘液稠度的标准试验方法》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F1080 93 (Reapproved 2013)Standard Test Method forDetermining the Consistency of Viscous Liquids Using aConsistometer1This standard is issued under the fixed designation F1080; the number immediately following the designation indicates the year oforiginal adoption or, in the case of rev

2、ision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 This test met

3、hod describes a procedure for the determi-nation of the flow of a standard volume of a semisolid or thickliquid under its own weight.1.2 The values stated in SI units are to be regarded as thestandard. The values in parentheses are for information only.1.3 This standard does not purport to address a

4、ll of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Summary of Test Method2.1 A sample of the material to be te

5、sted is poured into areservoir and the distance of flow in a horizontal direction isread from a ruled track after a fixed time following thematerials release from the reservoir.3. Significance and Use3.1 This measurement of flow gives results that cannot bepredicted with viscosity measurements, due

6、to surface tensionand density effects. The measured flow, is related to flowperformance of viscous materials sprayed on aircraft surfacesor other large structures.4. Apparatus4.1 Consistometer constructed as described in Annex A1.4.2 Timing Device accurate to 61s.4.3 Mixer capable of 1600 r/min and

7、fitted with a 25-mm(1-in.) diameter three-bladed propeller.4.4 Beaker, 500-mL.5. Procedure5.1 Bring the material to be tested and the apparatus to thesame ambient temperature in the range from 20 to 25C (68 to77F).5.2 Agitate 250 mL of the material to be tested using themixer set at 1600 r/min, for

8、1 min 6 5 s, or until a vortex formsthat indicates all of the sample has been exposed to shear.Avoid aeration of the sample as this may cause evaporation ofsolvents.5.3 Place the consistometer on a level surface and adjust theleveling screws until the bubble is centered.5.4 Close the consistometer g

9、ate and set the trigger.5.5 Fill the consistometer reservoir with the material to betested (approximately 100 mL), and level the surface with aspatula or a straight edge.5.6 Start the test by simultaneously tripping the consistom-eter gate trigger and starting the timing device. At 5 min 6 1s (unles

10、s otherwise specified), read the distance the materialhas flowed. Average the result to the nearest 0.5 cm by takingthe maximum distance indicated in the center of the trough andadding this to the minimum distance at the edge of the troughand dividing the result by two.6. Report6.1 The report shall

11、include the following:6.1.1 Material name or reference, type and lot number.6.1.2 Average distance of flow to nearest 0.5 cm.6.1.3 Test temperature in C to 61C.6.1.4 Duration of test in minutes and seconds.7. Precision and Bias7.1 Precision:7.1.1 ReproducibilityViscous materials often vary in con-si

12、stency dependent upon age, temperature, and shear history.Caution shall be exercised between laboratories regarding thehistory of a sample.7.1.2 Duplicate results by the same operator on the samesample shall be within 0.5 cm.1This test method is under the jurisdiction of ASTM Committee F07 onAerospa

13、ce and Aircraft and is the direct responsibility of Subcommittee F07.07 onQualification Testing of Aircraft Cleaning Materials.Current edition approved Dec. 1, 2013. Published December 2013. Originallyapproved in 1987. Last previous edition approved in 2008 as F1080 93(2008).DOI: 10.1520/F1080-93R13

14、.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States17.2 BiasNo statement can be made regarding bias as thereare no absolute nor widely accepted standards for the propertymeasured by the consistometer.8. Keywords8.1 consistometer; liquids

15、; viscousANNEX(Mandatory Information)A1. CONSISTOMETERA1.1 Consistometer shown in Fig. A1.1. It consists of thefollowing parts constructed of stainless steel.A1.1.1 Reservoir, 4-cm high, 5-cm long, fitted with springstainless steel trap door on one side.A1.1.2 Stainless Steel Track with side walls (

16、24 cm long, 5cm wide) with ruled markings each12 cm.A1.1.3 Leveling Device, for proper leveling of track.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that

17、 determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapprov

18、ed or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you fee

19、l that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual repr

20、ints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).FIG. A1.1 ConsistometerF1080 93 (2013)2