ASTM F1043-2006 Standard Specification for Strength and Protective Coatings on Steel Industrial Chain Link Fence Framework《金属工业链护栏框架强度和保护性涂层的标准规范》.pdf

《ASTM F1043-2006 Standard Specification for Strength and Protective Coatings on Steel Industrial Chain Link Fence Framework《金属工业链护栏框架强度和保护性涂层的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F1043-2006 Standard Specification for Strength and Protective Coatings on Steel Industrial Chain Link Fence Framework《金属工业链护栏框架强度和保护性涂层的标准规范》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 1043 06Standard Specification forStrength and Protective Coatings on Steel Industrial ChainLink Fence Framework1This standard is issued under the fixed designation F 1043; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revisi

2、on, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the strength and protectivecoating requirements for industrial steel chain

3、link fenceframework. Maximum allowable heights of framework andpost spacing are to be based on chain link fence fabric meshsize and gages, and specified wind loads. Post spacings are notto exceed 10 ft. (For additional information, see CLFMI GuideWLG2445.)1.1.1 Caution Regarding WindloadIf additives

4、 to thefence, such as windscreen, inserts, or signage are required, it isadvisable to use stronger framework and fittings, to reduce theon-center spacing of posts, or to add back bracing. Factors toconsider when determining windload include the type ofscreening material to be used, area of fence to

5、be covered andlocal wind conditions.1.2 Posts and rails may have any cross-sectional shapemeeting the requirements herein. The shapes may be formedand welded, cold formed, hot rolled, or extruded.1.3 The values in inch-pound units are to be regarded as thestandard. The values stated in SI units are

6、for informationpurposes only.NOTE 1For aluminum-alloy extruded structural pipe and tube pleaserefer to Specification B 429.2. Referenced Documents2.1 ASTM Standards:2A 90/A 90M Test Method for Weight Mass of Coating onIron and Steel Articles with Zinc or Zinc-Alloy CoatingsA 123/A 123M Specification

7、 for Zinc (Hot-Dip Galva-nized) Coatings on Iron and Steel ProductsA 653/A 653M Specification for Steel Sheet, Zinc-Coated(Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed)by the Hot-Dip ProcessA 875/A 875M Specification for Steel Sheet, Zinc-5 %Aluminum Alloy-Coated by the Hot-Dip ProcessA 1011/

8、A 1011M Specification for Steel, Sheet and Strip,Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy,High-Strength Low-Alloy with Improved Formability, andUltra-High StrengthB6 Specification for ZincB 429 Specification for Aluminum-Alloy Extruded Struc-tural Pipe and TubeB 750 Specification for

9、GALFAN (Zinc-5 % Aluminum-Mischmetal) Alloy in Ingot Form for Hot-Dip CoatingsD 1499 Practice for Filtered Open-Flame Carbon-Arc Ex-posures of PlasticsD 3359 Test Methods for Measuring Adhesion by Tape TestE 8 Test Methods for Tension Testing of Metallic MaterialsE 376 Practice for Measuring Coating

10、 Thickness byMagnetic-Field or Eddy-Current (Electromagnetic) Exami-nation MethodsF 552 Terminology Relating to Chain Link FencingF 934 Specification for Colors for Polymer-Coated ChainLink Fence MaterialsF 1083 Specification for Pipe, Steel, Hot-Dipped Zinc-Coated (Galvanized) Welded, for Fence Str

11、ucturesF 1553 Guide for Specifying Chain Link FenceG23 Practice for Operating Light-Exposure Apparatus(Carbon-Arc Type) With and Without Water for Exposureof Nonmetallic Materials (Discontinued 2001)3G26 Practice for Operating Light-Exposure Apparatus(Xenon-Arc Type) With and Without Water for Expos

12、ureof Nonmetallic Materials (Discontinued 2001)32.2 Other Documents:WLG2445 CLFMI Guide for the Selection of Line PostSpacings43. Terminology3.1 Definitions:3.1.1 postsvertical members of the fence.3.1.1.1 DiscussionEnd, corner, and pull posts are posts atwhich chain link fabric terminates. Gatepost

13、s are posts towhich gates are either attached or latched. Line posts are posts1This specification is under the jurisdiction of ASTM Committee F14 on Fencesand is the direct responsibility of Subcommittee F14.40 on Chain Link Fence andWire Accessories.Current edition approved Oct. 1, 2006. Published

14、October 2006. Originallyapproved in 1995. Last previous edition approved in 2004 as F 1043 - 04.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Docume

15、nt Summary page onthe ASTM website.3Withdrawn.4Available from Chain Link Fence Manufacturers Institute, 10015 Old ColumbiaRoad, Suite B-215, Columbia, MD 21046, http:/www.chainlinkinfo.org.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United Sta

16、tes.that occur in a line of fence in which the chain link fabricpasses and to which it is tied.3.1.2 railshorizontal members of the fence.3.1.2.1 DiscussionMay be top, bottom, intermediate orbrace rails.3.1.3 The dimensional terminology is shown in Fig. 1.3.1.4 The relationship of measured dimension

17、 (usedthroughout) to trade and industry usage is shown in Table 1.3.1.5 open sectionsnon-tubular framework sections (suchas H-posts, C-posts, roll-formed top rail, and terminal posts).3.1.6 polymer coatingsexamples of some polymer coat-ings are acrylic urethane, polyurethane, polyvinyl chloride(PVC)

18、, polyester, and polyolefin elastomer.3.1.7 See Terminology F 552 for definitions of other terms.4. Ordering Information4.1 Orders for steel fence framework purchased to thisspecification shall include the following information:4.1.1 Number of posts and rails by size and length,4.1.2 Type of outside

19、 and inside coating (Section 7) andclass of material,4.1.3 Color, if applicable, in accordance with SpecificationF 934,4.1.4 Material group (IA, IC, IC-L, II, II-L, III, III-L) (Table2),4.1.5 Certification, if required, and4.1.6 Exception(s) to this specification, or special require-ments, if any.NO

20、TE 2These details may be covered in whole or in any part byaccompanying the orders with design drawings and notations thereon.5. Strength Requirements5.1 It is the intent of this specification to permit thecontinuance of historically proved practice in the installation ofchain link fence systems, an

21、d to provide strength requirementsfor alternative shapes and materials. Two categories are de-scribed. Heavy industrial fence represents the most rigid andmechanically durable of the commonly installed framework.Light industrial/commercial fence, as provided herein, exhibitsapproximately 80 % of the

22、 load bearing capability of heavyindustrial fence. The summary requirements and options forheavy industrial fence are given in Table 3 and those of lightindustrial/commercial fence in Table 4.5.2 Historical PracticeExperience has shown that galva-nized steel performs satisfactorily as fence posts an

23、d rails iffurnished to the standard weight (Schedule 40) and nominalsizes listed in Specification F 1083. Therefore, fence posts andrails consisting of standard weight (Schedule 40) galvanizedFIG. 1 Definitions of Dimensional TermsTABLE 1 Size TerminologyTrade Size,in. mmDesignator,NPS Metric Actual

24、 Outside Diameterin. mm138 34.9 1 25 1.315 33.4158 41.3 114 32 1.660 42.22 50.8 112 40 1.900 48.3212 63.5 2 50 2.375 60.33 76.2 212 65 2.875 73.0312 88.9 3 80 3.500 88.94 101.6 312 90 4.000 101.6TABLE 2 Definitions of Fence Framework Materials DesignMaterial Description of MaterialGroup IARound Stee

25、l PipeSteel pipe shall be produced to conform to SpecificationF 1083, standard weight (Schedule 40).Group IC/IC-LRound Steel Pipe(Electric ResistanceWelded Pipe)Steel pipe shall be produced in accordance withcommercial standards. Minimum yield strength shall be50 000 psi 344 MPa. Such products shall

26、 include,without seeking to limit to, cold-formed and welded pipe.The minimum weight shall be not less than 90 % of thenominal weight.Group II/II-LRoll-Formed SteelShapes (C-Sections)Roll formed steel shapes shall be produced tocommercial standards. Minimum yield strength shall be50 000 psi 344 MPa,

27、 and 60 000 psi 413 MPa for the3.25 in. 3 2.50 in. line post sections. The minimumweight shall be not less than 90 % of the nominal weight.The formed lip shall be of the same thickness as the flatelements and shall project no less than13 the width ofthe flat element being stiffened. Group II product

28、s shallbe designated such that the strong axis is perpendicularto the line of fence.Group III/III-LHot-Rolled Shapes(H Beams)Hot-rolled shapes shall meet the specified criteria andexhibit a minimum yield strength of 50 000 psi 344MPa. The minimum weight shall be not less than 90 %of the nominal weig

29、ht.Group IVAlternate DesignAny suitable design can be delivered, provided it meetsthe strength and stiffness criteria of Table 3 (HeavyIndustrial) or Table 4 (Light Industrial/Commercial) andthe producer has supplied, in a form acceptable to thepurchaser, data that demonstrates conformance with thes

30、pecification. At the producers option the methods ineither Section 6 or 6.4 may be used.F 1043 062steel in the nominal sizes and weight per foot listed inSpecification F 1083 shall be considered in compliance withthis specification.5.2.1 Experience has also shown that several additionalproducts perf

31、ormed satisfactorily provided certain additionalrequirements are met. The nominal dimensions, minimumTABLE 3 Summary of Requirements for Heavy Industrial Fence FrameworkDescription Pipe Roll-Formed Hot-Formed Performance Criteria for Future ProductsMaterialIA IC II III IVSteel Steel Steel SteelRefer

32、enceSpecificationF 1083 A 653/A 653M,A 924/A 924M,A 1011/A 1011MA 1011/A 1011MGrade 50, OthersMinimumYieldStrength,psi MPa30 00020550 00034450 00034450 000344FrameworkSee Fig. 1 forDefinitions ofDimensional TermsSee Fig. 1 forDefinitions ofDimensional TermsSee Fig. 1 forDefinitions ofDimensional Ter

33、msBendingStrengthZ 3 YStiffnessE 3 IRail orBracesD = 1.660 in.42 mmT = 0.140 in.3.6 mm2.27 lb/ft3.38 kg/mD = 1.660 in.42 mmT = 0.111 in.2.8 mm1.84 lb/ft2.74 kg/mA = 1.625 in. 41.2 mmB = 1.25 in. 31.7 mmC = 0.375 in. 9.5 mmR = 0.1875 in. 4.76 mmT = 0.80 in. 2.0 mm1.35 lb/ft 2.01 kg/m7000 lbf/in.795 N

34、-m3 3 106lbf-in.28.6 kPa-m4Tmin= 0.075 in. 1.9 mmLine PostD = 1.900 in.48 mmT = 0.145 in.3.7 mm2.72 lb/ft4.05 kg/mD = 1.900 in.48 mmT = 0.120 in.3.0 mm2.28 lb/ft3.39 kg/mA = 1.875 in. 47.6 mmB = 1.625 in. 41.2 mmC = 0.5625 in. 14.3 mmR = 0.25 in. 6.4 mmT = 0.121 in. 3.1 mm2.40 lb/ft 3.39 kg/mTmin= 0

35、.105 in. 2.65 mm9800 lbf-in.1106 N-m7 3 106lbf-in.220 kPa-m4Line orTerminalPostD = 2.375 in.60 mmT = 0.154 in.3.9 mm3.65 lb/ft5.43 kg/mD = 2.375 in.60 mmT = 0.130 in.3.3 mm3.12 lb/ft4.64 kg/mA = 2.25 in. 57.2 mmB = 1.70 in. 43.2 mmC = 0.75 in. 19.1 mmR = 0.25 in. 6.4 mmT = 0.121 in. 3.1 mm2.78 lb/ft

36、 4.13 kg/m(Line Post Only)A = 2.25 in. 57.2 mmB = 1.70 in. 43.2 mmR = 0.25 in. 6.4 mma=10T = 0.125 in. 3.2 mm3.26 lb/ft 4.85 kg/m(Line Posts Only)16 800 lbf-in.1900 N-m16 3 106lbf-in.246 kPa-m4Line orTerminalPostD = 2.875 in.73 mmT = 0.203 in.5.2 mm5.79 lb/ft8.62 kg/mD = 2.875 in.73 mmT = 0.160 in.4

37、 mm4.64 lb/ft6.90 kg/mA = 3.25 in. 82.6 mmB = 2.50 in. 64.0 mmC = 1.00 in. 25.4 mmR = 0.25 in. 6.4 mmT = 0.130 in. 3.30 mm4.50 lb/ft 6.70 kg/m(60 000 min yield)(Line Post Only)Tmin= 0.125 in. 3.2 mm31 900 lbf-in.3606 N-m35 3 106lbf-in.2100 kPa-m4TerminalPostA = 3.50 in. 88.9 mmB = 1.50 in. 38.1 mmC

38、= 1.00 in. 25.4 mmR = 0.1875 in. 4.76 mmT = 0.135 in. 3.5 mm5.10 lb/ft 7.6 kg/m(Terminal Post Only)Tmin= 0.125 in. 3.2 mm31 900 lbf-in.3606 N-m35 3 106lbf-in2100 kPa-m4Line orTerminalPostD = 4.000 in.102 mmT = 0.226 in.5.7 mm9.11 lb/ft13.56 kg/mD=4.00in.102 mmT = 0.160 in.4.1 mm6.56 lb/ft9.76 kg.mTm

39、in= 0.145 in. 3.7 mm71 800 lbf-in.8114 N-m100 3 106lbf-in.2288 kPa-m4Line orTerminalPostD = 6.625 in.168 mmT = 0.280 in.7.11 mm18.97 lb/ft28.3 kg/mTmin= 0.270 in. 6.9 mm255 000 lbf-in.28 811 N-m800 3 106lbf-in.22300 kPa-m4A = outside dimensionB = outside dimensionC = lipD = outside diameterR = radiu

40、s at surface (max)a = flange taper (degree of angle)T = thickness (wall)See Fig. 1 fordrawings ofshapes.Y = yield strength, minZ = section modulusI = moment of inertiaE = modulus of elasticityF 1043 063yield strength (Y), and nominal weight/ft are also listed inTables 3 and 4. These satisfactory des

41、igns are classified inaccordance with products and special requirements as de-scribed in Table 2.6. Strength Calculations6.1 The strength of a structural member can generally bepredicted from established engineering principles. The intentof this section is to provide criteria by which alternate desi

42、gnscan be judged to provide adequate strength without prematurefailure by local buckling. Accordingly, the criteria of 6.2 and6.3 shall be satisfied even though, in general, only one willgovern a particular design.6.2 The elastic bending strength equals the yield strengthtimes the section modulus of

43、 the entire cross section.6.2.1 The yield strength may be considered to be either: (1)the minimum specified yield strength for material used to forma part, or (2) the value determined from tension tests performedin accordance with Test Method E 8. The specimen may be cuteither from material before f

44、orming or from the part afterfabrication.6.3 Accepted engineering practice indicates that the fullbending strength of a structure can be realized if the additionaldimensional restrictions shown below are satisfied.6.3.1 For circular shapes the ratio of the diameter to thethickness may not exceed 0.1

45、 E/Y.6.3.2 For cross-sectional shapes composed of flat elements,the ratio of width to thickness for elements supported alongtwo parallel edges may not exceed 1.2 (E/Y)1/2, and ratio ofTABLE 4 Summary of Requirements for Light Industrial/Commercial Fence FrameworkDescription Pipe Roll-Formed Hot-Form

46、ed Performance Criteria for Future ProductsMaterialIC-L II-L III-L IVSteel Steel SteelReferenceSpecificationA 653/A 653M,A 924/A 924M,A 1011/A 1011MA 1011/A 1011MGrade 50, OthersMinimumYield Strength,psi MPa50 00034450 00034450 000344FrameworkSee Fig. 1 forDefinitions ofDimensional TermsSee Fig. 1 f

47、orDefinitions ofDimensional TermsSee Fig. 1 forDefinitions ofDimensional TermsBending StrengthZ 3 YStiffnessE 3 IRail orBracesD = 1.660 in.42 mmT = 0.085 in.2.16 mm1.43 lb/ft2.12 kg/mA = 1.625 in. 41.2 mmB = 1.25 in. 31.7 mmC = 0.375 in. 9.5 mmR = 0.1875 in. 4.76 mmT = 0.080 in. 2.0 mm1.35 lb/ft 2.0

48、1 kg/m7000 lbf-in.795 N-m3 3 106lbf-in.28.6 kPa-m4Tmin= 0.075 in. 1.9 mmLine PostD = 1.900 in.48 mmT = 0.090 in.2.3 mm1.74 lb/ft2.59 kg/mA = 1.875 in. 47.6 mmB = 1.625 in. 41.2 mmC = 0.5625 in. 14.3 mmR = 0.25 in. 6.4 mmT = 0.105 in. 2.67 mm1.85 lb/ft 2.75 kg/m9800 lbf-in.1106 N-m6 3 106lbf-in.220 kPa-m4Tmin= 0.085 in. 2.15 mmLine orTerminalPostD = 2.375 in.60 mmT = 0.095 in.2.4 mm2.31 lb/ft3.44 kg/mA = 1.875 in. 47.6 mmB = 1.625 in. 41.2 mmC = 0.5625 in. 14.3 mmR = 0.25 in. 6.4 mmT = 0.121 in. 3.1 mm2.40 lb/ft 3.57 kg/m(Line Post Only)16 800 lbf-in.1900 N-m1