ASTM E803-1991(2008) 752 Standard Test Method for Determining the L D Ratio of Neutron Radiography Beams《中子射线照相束的长度直径比的标准测定方法》.pdf

《ASTM E803-1991(2008) 752 Standard Test Method for Determining the L D Ratio of Neutron Radiography Beams《中子射线照相束的长度直径比的标准测定方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM E803-1991(2008) 752 Standard Test Method for Determining the L D Ratio of Neutron Radiography Beams《中子射线照相束的长度直径比的标准测定方法》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E 803 91 (Reapproved 2008)Standard Test Method forDetermining the L/D Ratio of Neutron Radiography Beams1This standard is issued under the fixed designation E 803; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the ye

2、ar of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method defines an empirical technique for themeasurement of the effective collimation ratio, L/D, of n

3、eutronradiography beams. The technique is based upon analysis of aneutron radiographic image and is independent of measure-ments and calculations based on physical dimensions of thecollimator system. The values derived by this technique shouldbe more accurate than those based on physical measurement

4、s,particularly for poorly defined apertures.2. Referenced Documents2.1 ASTM Standards:2E 748 Practices for Thermal Neutron Radiography of Ma-terialsE 1316 Terminology for Nondestructive Examinations3. Summary of Test Method3.1 Determination of neutron beam L/D ratio using the NU(no umbra) technique3

5、is accomplished by radiographing theNU device with the neutron beam to be measured andsubsequently analyzing the radiograph by one of three meth-ods. Each of the three methods is based upon the determinationof that point at which the umbral shadow width reaches zero.See Fig. 1. A key feature of the

6、NU technique is that L/D canbe determined accurately without the need for expensiveinstrumentation. Neutron radiography practices are discussedin Practices E 748 and the terms are defined in TerminologyE 1316.4. Significance and Use4.1 The quality of a neutron radiographic image is depen-dent upon m

7、any factors. The L/D ratio is one of those factorsand constitutes a numerical definition of the geometry of theneutron beam. The L/D ratio required for a specific neutronradiographic examination is dependent upon the thickness ofthe specimen and the physical characteristics of the particularelement

8、of interest. Use of this test method allows theradiographer and the user to determine and periodically checkthe effective collimation ratio.5. Apparatus5.1 NU Device (see Figs. 2(a), 2(b), and 3) employs neutronabsorbing rods positioned at various distances from the imageplane. In practice this devi

9、ce consists of cadmium and nylonrods located in V-grooves accurately machined in the surface ofan aluminum channel section set at a 45 614 angle to the sidesupport plate. Near the image plane end the V-grooves aremachined on 0.283-cm centers. After 21 V grooves, countingone on the end, the grooves a

10、re machined on 0.707-cm centersto the source end. The 0.64-mm diameter cadmium and nylonrods are laid into the V-grooves and secured with neutrontransparent adhesive tape. The aluminum channel is supportedby side plates to maintain the 45 614 angle relative to theimage plane. While cadmium rods with

11、 diameters other than0.64 mm may be used, the exact rod diameter must be knownand the depth of the V grooves must be adjusted accordingly.5.2 A single A unit as shown in Fig. 2(b) is used for L/Dvalues expected to be less than 150. Alternately, a single A unitused with appropriate spacers may be use

12、d to accommodate awide range of L/D values.6. Procedure6.1 Place the NU device against the cassette with the finelyspaced rods nearest the cassette.6.2 Align the plane of the cassette perpendicular to the axisof the neutron beam.6.3 Expose the single-emulsion film and NU device for atime span that w

13、ill produce a nominal background film densityof 2.5 6 0.4.6.4 Process the exposed film in accordance with the manu-facturers recommendations.6.5 Analyze the resultant image in accordance with one ormore of the three methods outlined in Section 7.1This test method is under the jurisdiction of Committ

14、ee E07 on NondestructiveTesting and is the direct responsibility of Subcommittee E07.05 on Radiology(Neutron) Method.Current edition approved July 1, 2008. Published September 2008. Originallyapproved in 1986. Last previous edition approved in 2002 as E 803 91 (2002).2For referenced ASTM standards,

15、visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Newacheck, R. L., and Underhill, P. E., “The NU Method for Determining L/DRatio Of Neutron R

16、adiography Facilities,” Aerotest Operations, Inc., Report A.O.77-27, June 1977.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.2(a) Support Channel Subassembly with Rod SpacingFIG. 1 Diagram of Zero Umbra Image ConfigurationNOTE 1Rod

17、s at “A” positions are 1 cm each side of center line (22 ea.)NOTE 2Rods at “B” positions are 2 cm each side of center line (9 ea.)NOTE 3Rods at “C” positions are 2.5 cm each side of center line (1 ea.)NOTE 4All dimensions from base line to reduce accumulative errorsNOTE 5Rod arrangement shown for si

18、ngle system device. For an add-on device, to form a double system, extend the 11 spaces for 7.78 cm to 19spaces for 13.43 cm and eliminate the close spacing (20 for 5.65 cm)NOTE 6Rods held tightly in position with one layer of transparent tapeE 803 91 (2008)22(b) L/D Apparatus Assembly7. Data Analys

19、is7.1 Visual AnalysisAvisual determination of the L/D ratiocan be made directly from the neutron radiograph. Whenobserving the individual rod images, the umbral image can berecognized as the “white” line along the center of the rodimage. This “white” line will decrease in width for the rodslocated f

20、arther and farther from the film. At some point theumbral images will disappear. Beyond this point a less intensewhite line will appear and increase in width with increasing roddistance. Use of a 5 to 10-power magnifier will aid indetermining the point at which the “white” line disappears andthen in

21、creases in width with a decreased intensity. Based on thevisual observation, determine the rod with zero umbral widthand then determine its distance (b) from the cassette. The L/Dratio is as follows:L/D 5b/rod diameter!7.2 Microdensitometric AnalysisThe second data analysismethod is based on a micro

22、densitometric scan across thecadmium rod images beginning with the “0” position rodnearest the film. A typical scan is shown in Fig. 4.Adensitometer aperture of 20 3 300 m and no horizontalexpansion is suggested for this method. The value of b isobtained from the intersection of a straight line orig

23、inatingfrom the tip (low film density) of the scan of the “0” rod anda curved line through the tips of the remaining wave forms asshown in Fig. 4. This method gives the best results for L/Dratios up to a few hundred. Higher L/D ratios cannot bedetermined by this method due to the inability to obtain

24、 a stablewave form for large values of b.7.3 Alternative Microdensitometric AnalysisThis methodalso uses scanning microdensitometric traces for L/D ratiodeterminations and is applicable for both high and low L/Dratios. For this method the recommended microdensitometerE 803 91 (2008)3settings are: 20

25、 3 300-m aperture and 503 (or more) chartrecording expansion. These settings will produce individualwave forms as shown in Fig. 5. At least two wave forms mustbe scanned, one near the film plane and one other near the pointwhere the umbra disappears. Care must be taken not to gobeyond the point wher

26、e the umbral image disappears. Mi-crodensitometer settings must remain the same for all scans.For L/D ratios above 100, the “0” centimetre rod image shouldnot be used because the unsharpness due to the film/conversionscreen combination overrides the unsharpness due to the L/Dratio. For the lower L/D

27、 ratios (under ;100), the simplifiedequation using X2and U0for the “0” rod image may be usedwith good results.7.3.1 To determine the value of b it is necessary to measurethe umbral image width for the two rods selected. Thisdimension is measured along a horizontal line (parallel tobackground) throug

28、h the average of the low-density scan of theindividual wave form. The desired dimension is the distancebetween the intersections of this horizontal line with linesdrawn through the two sides of the wave form. The measure-ment may be centimetres or inches and need not be convertedto the unmagnified v

29、alue.7.3.2 Using this dimension, determine the value of b asfollows (see Fig. 6):b 5 U1X1!/U12 U2! 1 X0where:U1= umbral width of a rod near the image plane,U2= umbral image width of a rod near the distance wherethe umbra disappears,X0= distance from the film to the rod chosen for U1, cm,andX1= dista

30、nce between the two rods chosen for analysis,cm.Since L/D =brod diameter , it is possible to determine L/Ddirectly as follows:L/D 5FU1X1U12 U21 X0G/ rod diameterFor low L/D ratios (2 cm), and becausematerials with very high neutron attenuation coefficients areavailable, a unique approach to L/D rati

31、o determination ispossible. If an opaque rod with a diameter much smaller thanthe source diameter is placed near the image plane, an umbralshadow will be cast as shown in Fig. X1.1.X1.2 For a given source diameter (D) and a given roddiameter (d), there will be a rod to image plane distance (b)where

32、the width of the umbral shadow on the image plane willequal zero. For this particular distance a simple formula can bedeveloped to determine L/D ratio:DXYZ is similar to DSTZTherefore:L/D 5 b/dwhere:L = source to film distance (Note X1.1),D = source size = XY in Fig. X1.1,b = object to film distance

33、, andd = object size = ST in Fig. X1.1.NOTE X1.1When b LB. Therefore L may also beconsidered Source to Object Distance. Thus, if the rod diameter is known,the L/D ratio can be calculated because the value of b can be determinedfrom a neutron radiograph of a system of rods.X2. ACCURACYX2.1 The NU met

34、hod for determining L/D ratios is particu-larly accurate in the normal range of L/D ratios used forneutron radiography, that is, 20 to 250. Major sources ofinaccuracy are (1) the variations in the cadmium rod diameter;(2) the variations of conversion screen to centerline of first roddistances; (3) t

35、he inherent unsharpness of the film/conversionscreen system; and (4) the effect of conversion screen gammaon the film density of the cadmium rods. (4) applies primarilyto the method of L/D determination using a 1:1 microdensito-meter scan of all rods.X2.2 Use of the linear regression analysis of ind

36、ividual rodumbral image measurements should provide accuracies of ;2to 3 % for L/D ratios up to 1000 assuming the cadmium rodFIG. 6 Diagrammatic Math ModelFIG. X1.1 Zero Umbra GeometryE 803 91 (2008)6diameter is accurately known. Any of the analysis techniquesutilizing microdensitometer scans should

37、 provide an accuracyof ;5 % for L/D ratios up to 250 and the visual observation isequally accurate when interpreted by a trained film reader.X2.3 The visual determination has certain limitations fixedby rod spacing. For example, if the umbral image is observedat 4 cm but is not visible in the 4.5-cm

38、 rod image, one can onlysay that the L/D lies between (4/0.064) and (4.5/0.064) or 62.5and 70.3. The accuracy is therefore limited to 12.5 %. Simi-larly at an L/D of 20, because the cadmium rods are spaced at0.2 cm, the best visual accuracy is limited to 16.7 % (between18.75 and 21.87 L/D).X2.4 The

39、accuracies noted above have been experimentallyverified by analysis of neutron radiographic images producedwith facilities having well defined geometrical configurations.The most significant point to be considered in the use of theNU method for determining L/D ratios is that the image is atrue indic

40、ator. If the values of L/D determined by the NUmethod disagree with the values determined by geometricalcalculations based on alleged source size and source to filmdistances, it is most probable that the NU method values aremore accurate. One should proceed to analyze the sourceconfiguration with pi

41、nhole techniques to locate source leakageor other problems should the values differ widely. The tech-nique has been found to be equally accurate for circular orsquare aperture configurations. In the case of a rectangular oroval shaped aperture, the NU device will indicate the L/D rationormal to the

42、rod direction. Two measurements are necessaryto characterize the source.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of

43、 any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments ar

44、e invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not rec

45、eived a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).E 803 91 (2008)7