ASTM E2707-2015 Standard Test Method for Determining Fire Penetration of Exterior Wall Assemblies Using a Direct Flame Impingement Exposure《使用直接火焰接触暴露方法测定外墙组件火焰穿透性的标准试验方法》.pdf

《ASTM E2707-2015 Standard Test Method for Determining Fire Penetration of Exterior Wall Assemblies Using a Direct Flame Impingement Exposure《使用直接火焰接触暴露方法测定外墙组件火焰穿透性的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM E2707-2015 Standard Test Method for Determining Fire Penetration of Exterior Wall Assemblies Using a Direct Flame Impingement Exposure《使用直接火焰接触暴露方法测定外墙组件火焰穿透性的标准试验方法》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E2707 14E2707 15 An American National StandardStandard Test Method forDetermining Fire Penetration of Exterior Wall AssembliesUsing a Direct Flame Impingement Exposure1This standard is issued under the fixed designation E2707; the number immediately following the designation indicates t

2、he year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This fire-test-response standard prescribes a met

3、hod to assess the fire performance of a vertically oriented specimen exposedto direct flame impingement in a simulated external fire exposure potentially encountered in a Wildland Urban Interfacescenario.This test method provides data suitable for comparing the performance of materials, which are us

4、ed as the exposed surfaces ofexterior walls in construction applications.NOTE 1This test method closely follows the test procedure of California Office of State Marshal (SFM) Method 12-7A-1.21.2 This test method measures the ability of the wall system to resist fire penetration from the exterior int

5、o the wall cavity orunexposed side of the test assembly under the conditions of exposure.1.3 This test method provides data suitable for comparing the performance of vertically oriented materials, products orassemblies in exterior construction applications. The test specimen shall be tested in thick

6、nesses and configurations representativeof actual end product or system uses.1.4 Limitations of the test method are listed in Section 5.5.1.5 The system of units to be used in referee decisions is the SI system of units; see IEEE/ASTM SI-10 for further details. Theunits given in parentheses are for

7、information only.1.6 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame undercontrolled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials,products, or assemblies

8、 under actual fire conditions.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatorylimitations

9、prior to use.1.8 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting thesetests.2. Referenced Documents2.1 ASTM Standards:3D2898 Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire TestingD4442 Test Methods for

10、Direct Moisture Content Measurement of Wood and Wood-Based MaterialsD4444 Test Method for Laboratory Standardization and Calibration of Hand-Held Moisture MetersD6662 Specification for Polyolefin-Based Plastic Lumber Decking BoardsD7032 Specification for Establishing Performance Ratings for Wood-Pla

11、stic Composite Deck Boards and Guardrail Systems(Guards or Handrails)E176 Terminology of Fire StandardsE1354 Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen ConsumptionCalorimeter1 This test method is under the jurisdiction ofASTM Committee E05 on Fire

12、 Standards and is the direct responsibility of Subcommittee E05.14 on External Fire Exposures.Current edition approved July 15, 2014Oct. 1, 2015. Published August 2014November 2015. Originally approved in 2009. Last previous edition approved in 20092014as E270709.14. DOI: 10.1520/E2707-14.10.1520/E2

13、707-15.2 2007 California Building Code, Chapter 7A SFM, Materials and Construction Methods for Exterior Wildfire Exposure, Exterior Wall Siding and Sheathing, SFMStandard 12-7A-1.3 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org.

14、For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may

15、 not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbo

16、r Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1E1474 Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or CompositesUsing a Bench Scale Oxygen Consumption CalorimeterE1740 Test Method for Determining the Heat Release Rate and Ot

17、her Fire-Test-Response Characteristics of Wall Covering orCeiling Covering Composites Using a Cone CalorimeterE2102 Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant HeaterE2257 Test Method for Room Fire Test of Wall and Ceiling Materials and As

18、sembliesE2886 Test Method for Evaluating the Ability of Exterior Vents to Resist the Entry of Embers and Direct Flame ImpingementIEEE/ASTM SI-10 American National Standard for Use of the International System of Units (SI): The Modern Metric System2.2 ISO Standards:ISO 13943 Fire SafetyVocabulary43.

19、Terminology3.1 DefinitionsFor definitions of terms used in this standard, see Terminology E176 and ISO 13943. In case of conflict, thedefinitions given in Terminology E176 shall prevail.3.2 Definitions of Terms Specific to This Standard:3.2.1 orientation, nthe vertical plane in which the exposed fac

20、e of the test specimen is located during testing.3.2.2 siding (cladding), nany material that constitutes the exposed exterior covering of an exterior wall and such material isapplied over sheathing or directly attached to the wall system.3.2.3 sheathing, nthe material placed on an exterior wall bene

21、ath cladding or siding and directly attached to the wall systemused over the wall framework and is attached directly to the wall framing members. Materials called sheathing that are not placedbeneath cladding or siding shall be classified as cladding or siding.3.2.4 sustained flaming, nflame on or o

22、ver the surface of a test specimen that lasts longer than a period of 4 s.4. Summary of Test Method4.1 This test method provides for the direct flame exposure of a wall specimen to a flame source centered at the base of a 1220by 2440 mm (4 by 8 ft) test assembly.4.2 This test method employs a gas bu

23、rner to produce a diffusion flame in contact with the test wall assembly.4.3 The gas burner produces a prescribed net rate of heat output of 150 kW (8535 BTU/min) for a period of 10 min, after whichthe flame exposure is terminated.4.4 The test method measures the ability of the wall system to resist

24、 fire penetration from the exterior to the unexposed sideof the test assembly under the conditions of exposure. Observations are made for the appearance of sustained flaming or glow onthe unexposed side or sustained glowing on the unexposed side, or both, at the end of a 60 min observation period.5.

25、 Significance and Use5.1 The test method described herein measures the ability of the exterior wall covering material or system to resist firepenetration from the exterior to the unexposed side of the wall assembly under the specified conditions of exposure.5.2 Representative joints and other charac

26、teristics of an assembly shall be included in a test specimen when these details arerepresentative of the construction of the end-use product(s).5.3 This test method is applicable to end-use product(s) not having an ideally planar external surface.5.4 The overall performance of the test specimen is

27、visually documented by full-color photographic records. Video taping ofthe complete fire test is an acceptable alternative to the photographic record. The use of infrared photography of the unexposedside of the test wall can be used to reveal development of increasing temperatures or persisting hot

28、spots.5.5 In this procedure, the specimens are subjected to a specific set of laboratory fire test exposure conditions. If different testconditions are substituted or the anticipated end-use conditions are changed, it is not known whether it is possible by use of thistest to predict changes in the p

29、erformance characteristics measured. Therefore, the results are strictly valid only for the fire testexposure conditions described in this procedure.6. Safety Precautions6.1 The test procedures involve high temperatures and combustion processes. Therefore, the potential exists for burns, ignitionof

30、extraneous objects or clothing, and for inhalation of combustion products.7. Apparatus7.1 Unless otherwise noted, dimensions in the following descriptions, shall be followed with a tolerance of 613 mm (0.5 in.).4 Available from International Organization for Standardization (ISO), 1, ch. de la Voie-

31、Creuse, Case postale 56, CH-1211, Geneva 20, Switzerland, http:/www.iso.ch.E2707 1527.2 Wall Assembly Holding FixtureThe test specimen support assembly shown in Fig. 1 is designed to permit rapid installationand removal of wall assemblies, and to prevent edge penetration of fire at the margins of th

32、e wall assembly. It includes a sturdyframe assembly to hold the specimen and a simulated soffit that is non-combustible. The frame assembly permits a 1220 by 2440mm (4 by 8 ft) prefabricated wall section to be inserted from the rear and to seal in such a way that protects the edges from fire.Side sh

33、ields are situated near the vertical edges and to within 304 mm (12 in.) of the top of the test wall assembly as shown inFig. 1 to aid in minimizing extraneous drafts to the surface of the assembly.7.3 Burner DetailsThe ignition source for the test shall be a gas diffusion burner with a nominal 100

34、mm wide by 1000 mmlong (4 in. wide by 39 in. long) porous top surface of a refractory material, as shown in Fig. 2. With the exception of top surfacedimensions, the essential configuration of the burner is comparable to the burner design described in Test Method E2257.7.4 The burner enclosure shall

35、be positioned so that it is centered relative to the width of the test wall. The distance from thebottom of the test specimen to the top surface of the burner shall be 300 6 50 mm (12 6 2 in.). The bottom of the test specimenshall be protected from burner fire exposure by the placement of a 1220 mm

36、(4 ft) wide thermal barrier consisting of nominal 19mm (0.75 in.) cement board (or equivalent) between the burner enclosure and the test specimen. The burner enclosure shall be incontact with the protective barrier. The thermal barrier shall be positioned so that the top edge extends 76 6 25 mm (3 6

37、 1 in.)above the top edge of the burner, and fastened to the base of the wall in such a manner to prevent obstruction of the burner flamecaused by distortion away from the surface of the wall. Any gaps between the top edge of the thermal barrier and the test wallsurface shall be filled with ceramic

38、wool, or equivalent, prior to the test.7.5 Natural gas, methane or propane shall be supplied to the burner through a metered control system. The gas supply to theburner shall produce a net heat output of 150 6 8 kW (8535 6 454 Btu/min) throughout the flame exposure.7.6 The burner shall be ignited by

39、 a pilot burner or a remotely controlled spark igniter.7.7 Moisture MeterMoisture meters used to determine the moisture content of wood products for compliance with 8.8.4.2shall be calibrated as described in Test Method D4444.8. Test Specimen8.1 Test specimens dimensions shall be 1220 mm (4 ft) wide

40、 by 2440 mm (8 ft) high. The test specimen shall be representativeof the end-use wall assembly except as specified in 8.3 and 8.4. The test specimen shall be mounted in the steel frame holdingfixture assembly as shown in Fig. 1.FIG. 1 Test FixtureE2707 1538.2 The test specimen shall incorporate join

41、t detail(s) representative of actual installation.8.3 For wall assemblies without internal cavity spaces, the entire wall assembly shall constitute the test specimen to be tested.The wall assembly shall be constructed in accordance with manufacturers specifications or building code requirements, or

42、both,where applicable. Other components of the wall assembly, such as building felt and sheathing, are employed to conform to themanufacturers specifications or building codes, or both.8.4 For wall assemblies with internal cavity spaces, the materials on what would be considered the interior (unexpo

43、sed) sideof the wall assembly shall be omitted from the test specimen. Materials such as insulation normally installed within the cavity spaceshall be omitted from the test specimen. The wall assembly used as the test specimen shall include the structural support elementsand any sheathing, weather b

44、arrier and cladding attached to the exterior surface of the structural support elements.8.5 For wall assemblies composed of layered materials, such as sheathing, siding (cladding) and underlayment, the installationof such layered materials shall be in accordance with manufacturers instructions, or i

45、n the absence of such instructions, applicablebuilding code requirements. In the absence of manufacturers specifications, the wall assembly shall include the followingminimum components: nominal 2 by 4 studs spaced 410 mm (16 in.) on center, and the desired exterior siding material. If sheathingis u

46、sed, tests shall be run on typical 7/16 in. oriented strandboard (OSB) of Exposure 1 rating.Where specified by the manufacturer,sheathing material and installation shall be in accordance with the manufacturers instructions. The sheathing shall have onevertical seam on a selected stud with a 3 mm (0.

47、125 in.) gap. The type, thickness, and installation method of any sheathing shallbe included in the report.8.6 Protect the vertical and horizontal edges of the test specimen with 12-mm ceramic wool blanket (or equivalent) to eliminatethe gap between the holder and the test specimen and prevent unwan

48、ted edge effects caused by heat transfer to the edges of thetest specimen through the sample holder.8.7 ReplicatesThree matched test specimen assemblies shall be tested.8.8 Accelerated Aging/Weathering and Pre-test Conditioning of Test Material:8.8.1 When it is anticipated that a regulatory or other

49、 agency will require pre-test accelerated aging/weathering of the samples,the manufacturer shall have the option to conduct such weathering. Weathering shall be conducted as specified by the regulatoryagency or applicable methods as specified for the product. The process shall evaluate the potential for the fire test responsecharacteristics as measured in this test method to deteriorate due to accelerated aging/weathering of the wall material. Details ofthe weathering method used, or reference to a standard test method, shall be included in the report (see