ASTM E2699-2010 Standard Practice for Digital Imaging and Communication in Nondestructive Evaluation (DICONDE) for Digital Radiographic (DR) Test Methods《数字射线照相(DR)试验方法用无损评估(DICOND.pdf

《ASTM E2699-2010 Standard Practice for Digital Imaging and Communication in Nondestructive Evaluation (DICONDE) for Digital Radiographic (DR) Test Methods《数字射线照相(DR)试验方法用无损评估(DICOND.pdf》由会员分享，可在线阅读，更多相关《ASTM E2699-2010 Standard Practice for Digital Imaging and Communication in Nondestructive Evaluation (DICONDE) for Digital Radiographic (DR) Test Methods《数字射线照相(DR)试验方法用无损评估(DICOND.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E2699 10Standard Practice forDigital Imaging and Communication in NondestructiveEvaluation (DICONDE) for Digital Radiographic (DR) TestMethods1This standard is issued under the fixed designation E2699; the number immediately following the designation indicates the year oforiginal adopti

2、on or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice facilitates the interoperability of digitalX-ray imaging equ

3、ipment by specifying image data transferand archival methods in commonly accepted terms. Thisdocument is intended to be used in conjunction with PracticeE2339 on Digital Imaging and Communication in Nondestruc-tive Evaluation (DICONDE). Practice E2339 defines an indus-trial adaptation of the NEMA St

4、andards Publication titledDigital Imaging and Communications in Medicine (DICOM,see http:/medical.nema.org), an international standard forimage data acquisition, review, storage and archival storage.The goal of Practice E2339, commonly referred to as DI-CONDE, is to provide a standard that facilitat

5、es the display andanalysis of NDE results on any system conforming to theDICONDE standard. Toward that end, Practice E2339 providesa data dictionary and a set of information modules that areapplicable to all NDE modalities. This practice supplementsPractice E2339 by providing information object defi

6、nitions,information modules and a data dictionary that are specific todigital X-ray test methods.1.2 This practice has been developed to overcome the issuesthat arise when analyzing or archiving data from digital X-rayequipment test using proprietary data transfer and storagemethods. As digital tech

7、nologies evolve, data must remaindecipherable through the use of open, industry-wide methodsfor data transfer and archival storage. This practice defines amethod where all the digital X-ray technique parameters andtest results are communicated and stored in a standard mannerregardless of changes in

8、digital technology.1.3 This practice does not specify:1.3.1 A testing or validation procedure to assess an imple-mentations conformance to the standard.1.3.2 The implementation details of any features of thestandard on a device claiming conformance.1.3.3 The overall set of features and functions to

9、be ex-pected from a system implemented by integrating a group ofdevices each claiming DICONDE conformance.1.3.4 Although this practice contains no values that requireunits, it does describe methods to store and communicate datathat do require units to be properly interpreted. The SI unitsrequired by

10、 this practice are to be regarded as standard. Noother units of measurement are included in this standard.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety an

11、d health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2E1316 Terminology for Nondestructive ExaminationsE1475 Guide for Data Fields for Computerized Transfer ofDigital Radiological Examination DataE2339 Practice for Digit

12、al Imaging and Communication inNondestructive Evaluation (DICONDE)E2597 Practice for Manufacturing Characterization of Digi-tal Detector Arrays2.2 Other Standard:3DICOM National Electrical Manufacturers AssociationStandard for Digital Imaging and Communications inMedicine (DICOM), 20083. Terminology

13、3.1 Definitions:3.1.1 Nondestructive evaluation terms used in this practicecan be found in Standard Terminology for NondestructiveExaminations, E1316.1This practice is under the jurisdiction of ASTM Committee E07 on Nonde-structive Testing and is the direct responsibility of Subcommittee E07.11 on D

14、igitalImaging and Communication in Nondestructive Evaluation (DICONDE).Current edition approved June 1, 2010. Published June 2010. DOI:10.1520/E2699-10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMSta

15、ndards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from National Electrical Manufacturers Association (NEMA), 1300N. 17th St., Suite 1752, Rosslyn, VA 22209, http:/www.nema.org.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West

16、Conshohocken, PA 19428-2959, United States.3.1.2 DICONDE terms used in this practice are defined inPractice E2339.3.1.3 Digital detector array terms used in this practice aredefined in Practice E2597.4. Summary of Practice4.1 A fundamental principle of DICONDE is the use ofstandard definitions and a

17、ttribute formats for data communica-tion and storage. This means all systems that are DICONDEcompliant use a common data dictionary and common com-munication protocols. To further standardization, the elementsin the data dictionary are organized into common groupsreferred to as information modules.

18、The data dictionary andinformation modules common to all NDE modalities aredefined in Practice E2339.4.2 The data dictionary and information modules specifiedin Practice E2339 do not cover the information storagerequirements for each individual modality (CT, DR, CR, UT,etc.). Additions to the data d

19、ictionary and information modulesare required to support the individual modalities. This practicecontains the additions to the DICONDE data dictionary andinformation modules necessary for digital X-ray inspection.4.3 The highest organizational level in the DICONDEinformation model is the information

20、 object definition (IOD).An information object definition is a collection of the infor-mation modules necessary to represent a set of test results froma specific modality. This practice contains information objectdefinitions for digital X-ray inspection.5. Significance and Use5.1 Personnel that are

21、responsible for the creation, transfer,and storage of digital X-ray test results will use this standard.This practice defines a set of information modules that alongwith Practice E2339 and the DICOM standard provide astandard means to organize digital X-ray test parameters andresults. The digital X-

22、ray test results may be displayed andanalyzed on any device that conforms to this standard. Person-nel wishing to view any digital X-ray inspection data storedaccording to Practice E2339 may use this document to helpthem decode and display the data contained in the DICONDE-compliant inspection recor

23、d.6. Information Object Definitions6.1 Digital X-ray Image IOD Description:6.1.1 The digital X-ray (DX) Image Information ObjectDefinition specifies an image that has been created by a directdigital X-ray imaging device for NDE purposes. To avoidduplication of relevant material from the DICOM standa

24、rd, theIOD definition will follow that for DX Images found in Part 3,section A.26 of the DICOM standard except as noted below inTable 1. Table 1 is not stand-alone and must be used inconjunction with Part 3, section A.26 of the DICOM standardto have a complete definition of the NDE DX informationobj

25、ect. This IOD will use the Service-Object Pair (SOP)Classes for the DX IOD as defined in Part 4 of the DICOMstandard.6.2 Digital X-ray Multi-Frame Image IOD Description:6.2.1 The digital X-ray (DX) Multi-frame (MF) ImageInformation Object Definition specifies an image that has beencreated by a direc

26、t digital X-ray imaging device for NDEpurposes. To avoid duplication of relevant material from theDICOM standard, the IOD definition will follow that forEnhanced X-ray Angiographic (Enhanced XA) Images foundin Part 3, section A.47 of the DICOM standard except as notedbelow in Table 2. Table 2 is not

27、 stand-alone and must be usedin conjunction with Part 3, section A.47 of the DICOMstandard to have a complete definition of the NDE DX-MFinformation object. This IOD will use the Service-Object Pair(SOP) Classes for the Enhanced XA IOD as defined in Part 4of the standard.7. Information Modules7.1 ND

28、E DX Detector Module:7.1.1 Table 3 specifies the Attributes that describe NDEDirect Digital X-ray (DX) Detectors.7.1.1.1 For NDE DX Images, Detector Type (0018,7004) isspecified to use the following defined terms.DIRECTSCINTILLATOR7.1.1.2 For NDE DX Images, Detector Configuration(0018,7005) is speci

29、fied to use the following defined terms.AREALINEAR7.2 NDE DX Calibration Data Module:7.2.1 Table 4 specifies the Attributes that describe NDEdirect digital X-ray calibration data.8. Keywords8.1 DICOM; DICONDE; direct digital X-ray; DX; digitaldata transmission; digital data storage; database; file f

30、ormatE2699 102TABLE 1 DX Image Information Object DefinitionDICOM Module DICONDE Module Reference UsageAPatient Component Practice E2339, Section 7 MSpecimen Identification Not ApplicableClinical Trial Subject Not ApplicableGeneral Study Component Study Practice E2339, Section 7 MPatient Study Not A

31、pplicableClinical Trial Study Not ApplicableGeneral Series Component Series Practice E2339, Section 7 MClinical Trial Series Not ApplicableGeneral Equipment NDE Equipment MContrast/Bolus Not ApplicableDX Anatomy Imaged Needed for DICOM compatibilityDX Detector NDE DX Detecto 7.1 MNDE Indication Prac

32、tice E2339, Section 7 UNDE Geometry Practice E2339, Section 7 UNDE DX Calibration 7.2 UDataAcquisition Content Needed for DICOM compatibilityADefinition of usage codes can be found in Part 3, section A.1.3 of the DICOM standard.TABLE 2 DX MF Image Information Object DefinitionDICOM Module DICONDE Mo

33、dule Reference UsageAPatient Component Practice E2339, Section 7 MSpecimen Identification Not ApplicableClinical Trial Subject Not ApplicableGeneral Study Component Study Practice E2339, Section 7 MPatient Study Not ApplicableClinical Trial Study Not ApplicableGeneral Series Component Series Practic

34、e E2339, Section 7 MClinical Trial Series Not ApplicableGeneral Equipment NDE Equipment Practice E2339, Section 7 MEnhanced Contrast/Bolus Not ApplicableAcquisition Context Needed for DICOMcompatibilityCardiac Synchronization Not ApplicableRespiratory Synchronization Not ApplicableX-Ray Detector NDE

35、 DX Detector 7.1 MNDE Indication E2339, Section 7 UNDE Geometry Practice E2339, Section 7 UNDE DX Calibration 7.2 UDataADefinition of usage codes can be found in Part 3, section A.1.3 of the DICOM standard.E2699 103TABLE 3 NDE DX Detector Module AttributesAttribute Name DICOM Tag DICONDE Tag VR VM T

36、ypeADescriptionDetector Type (0018,7004) CS 1 2 The type of detector used to acquire projection data.Detector Configuration (0018,7005) CS 1 3 The physical configuration of the detector.Detector Description (0018,7006) LT 1 3 Free-text description of the detector.Detector Mode (0018,700A) LT 1 3 Tex

37、t description of the operating mode of the detector.Detector ID (0018,7008) SH 1 3 The ID or serial number of the detector used to acquire projectiondata.Date of Last Detector Calibration (0018,700C) DA 1-n 3 Date of the last calibration for the equipment.Time of Last Detector Calibration (0018,700E

38、) TM 1-n 3 Time of the last calibration for the equipment.Detector Active Time (0018,7014) DS 1 3 Time in msec that the detector is active during acquisition of thisdata.Detector Activation Offset from Exposure (0018,7016) DS 1 3 Offset time in msec that the detector becomes active after the X-raybe

39、am is turned on during the acquisition of this data. May benegative.Detector Binning (0018,701A) DS 2 3 Number of active detectors used to generate a single pixel.Specified as the number of row detectors per pixel followed by thenumber of column detectors.Internal Detector Frame Time (0009,XX11) DS

40、1 3 The time in msec that the detector is acquiring an image.Number of Frames Integrated (0009,XX12) DS 1 3 The number of frames integrated to form an image.Detector Manufacturers Name (0018,702A) LO 1 3 Name of the manufacturer of the detector component of theacquisition system.Detector Manufacture

41、rs Model Number (0018,702B) LO 1 3 Model number of the detector component of the acquisition system.Detector Conditions Nominal Flag (0018,7000) CS 1 3 A flag that indicates whether or not the detector is operating withinnormal tolerances during data acquisition. This flag is intended toindicate whe

42、ther there has been some compromise of the diagnosticquality of the data due to some operating condition (for example,overheating).Sensitivity (0018,6000) DS 1 3 Detector sensitivity in manufacturer specific units.BField of View Shape (0018,1147) CS 1 3 Shape of the Field of View, that is, the image

43、 pixels.Field of View Dimension(s) (0018,1149) IS 1-2 3 Dimensions in mm of the Field of View.Field of View Origin (0018,7030) DS 2 1C Required if the Field of View has been rotated or flipped. Offset ofthe Top Left Hand Corner (TLHC) of arectangle circumscribing theField of View before rotation or

44、flipping, from the TLHC of thephysical detector area measured in physical detector pixels as a rowoffset followed by a column offset.Field of View Rotation (0018,7032) DS 1 1C Required if the Field of View has been rotated. Clockwise rotation indegrees of the Field of View relative to the physical d

45、etector.Field of View Horizontal Flip (0018,7034) CS 1 1C Required if the Field of View has been rotated. Whether or not ahorizontal flip has been applied to the Field of View after rotationrelative to the physical detector as described in the Field of ViewRotation.Imager Pixel Spacing (0018,1164) D

46、S 2 1 Physical distance measured at the front plane of the detectorhousing between the center of each image pixel specified by anumeric pair row spacing value followed by a column spacingvalue in mm.Detector Element Physical Size (0018,7020) DS 2 3 Physical dimensions of each detector element in mm

47、that comprisesthe detector matrix. Expressed as the rowdimension followed by thecolumn dimension.Detector Element Spacing (0018,7022) DS 2 3 Physical distance between the center of each detector element,specified by a numeric pair row spacing value in mm followed bycolumn spacing value in mm.Detecto

48、r Active Shape (0018,7024) CS 1 3 Shape of the active area.Detector Active Dimension(s) (0018,7026) DS 1-2 3 Dimension(s) in mm of the active area.Detector Active Origin (0018,7028) DS 2 3 Offset of the TLHC of a rectangle circumscribing the active detectorarea from the TLHC of a rectangle circumscr

49、ibing the physicaldetector area, measures in physical detector pixels as a row offsetfollowed by a column offset.Detector Temperature Sequence (0009,XX20) SQ 1 3 Sequence that contains detector temperature information.Sensor Name (0009,XX22) DS 1 3 The name of the sensor.Horizontal Offset (0009,XX24) DS 1 3 The horizontal offset in mm from the left position of the detector.Vertical Offset (0009,XX26) DS 1 3 The vertical offset in mm from the top position of the detector.Temperature (0009,XX28) DS 1 3 Temperature in Celsius of the sensor.ADefinition of type codes can be foun