ASTM E2631-2009(2015) Standard Practice for Physical Placement of an Entity-Controlled Supplemental Identification Label《实体控制补充识别标签的实际位置的标准实践规程》.pdf

《ASTM E2631-2009(2015) Standard Practice for Physical Placement of an Entity-Controlled Supplemental Identification Label《实体控制补充识别标签的实际位置的标准实践规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM E2631-2009(2015) Standard Practice for Physical Placement of an Entity-Controlled Supplemental Identification Label《实体控制补充识别标签的实际位置的标准实践规程》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E2631 09 (Reapproved 2015)Standard Practice forPhysical Placement of an Entity-Controlled SupplementalIdentification Label1This standard is issued under the fixed designation E2631; the number immediately following the designation indicates the year oforiginal adoption or, in the case o

2、f revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice is for supplemental identification labelsassigned by an entity and affixed to eq

3、uipment to permitcontrol.1.2 Identifying labels include, but are not limited to, remov-able tags, bands, and plates.1.3 This practice is not intended for material or manufac-turers warranties.1.4 This practice is not intended for original equipmentmanufacturers (OEMs) markings.1.5 The values stated

4、in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.6 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and he

5、alth practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2E2135 Terminology for Property and Asset ManagementE2279 Practice for Establishing the Guiding Principles ofProperty ManagementE2452 Practice for Equipment Management Pro

6、cess Matu-rity (EMPM) Model2.2 Federal Standard:3MIL STD 130 Standard Practice for Identification Markingof U.S. Military Property3. Terminology3.1 DefinitionsSee Terminology E2135 for definitionsrelated to property and asset management.3.1.1 impractical, adjunwise to implement or maintain inpractic

7、e.3.1.2 label, nan identifying or descriptive marker that isattached to an object.3.1.3 placement, nact of placing, adhering, or affixing alabel in a certain place or location.3.1.4 supplemental, advsomething added to provide fur-ther information.4. Summary of Practice4.1 The intent of this practice

8、 is to provide uniform guid-ance for the physical placement of a supplemental label onequipment in the possession or control of an entity.5. Significance and Use5.1 There is no consistent method for the physical place-ment of an identifying label on equipment in the possession ofan entity.5.2 This p

9、ractice is intended to expedite and improve thephysical inventory and self-assessment processes and otheroccasions in which the instant identification of equipment isneeded for purposes of control, management, or determiningownership, or a combination thereof.5.3 The further intent of this practice

10、is to reduce theadministrative costs associated with activities requiring equip-ment identification, that is, physical inventory, self-assessments, and audits and to supplement Practice E2279,Practice E2452, and MIL STD 130.6. Procedure6.1 When space allows, the label shall be physically placedon th

11、e equipment item so that it directly faces the user. Thelabel shall be consistently placed, that is, placed in the samelocation or approximate location, does not overlay the OEMmarking, and can be conveniently read. The placement andreading of the tag should not require movement or the propertynor d

12、isrupt any processing that it supports. (See Fig. 1.)1This practice is under the jurisdiction of ASTM Committee E53 on AssetManagement and is the direct responsibility of Subcommittee E53.01 on ProcessManagement.Current edition approved Jan. 1, 2015. Published January 2015. Originallyapproved in 200

13、9. Last previous edition approved in 2009 as E263109. DOI:10.1520/E2631-09R15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page on

14、the ASTM website.3Available from U.S. Government Publishing Office, 732 N. Capitol St., NW,Washington, DC 20401-0001, http:/www.gpo.gov.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States16.2 When space is insufficient, the label shall be

15、 physicallyplaced on the front right side of the equipment, or the rear forrack mounted equipment. The label shall be consistentlyplaced, that is, placed in the same location or approximatelocation, does not overlay the OEM marking, and can beconveniently read. (See Fig. 2.)6.3 If for any reason the

16、 supplemental label is necessary butphysically impractical, the same information should be affixedto a protective covering or by a temporary bond, such as a shoetag, and shall be contained in the equipment record. (See Fig.3.)6.3.1 If a supplemental label is necessary but physicallyimpractical to at

17、tach, the property system record used tocontrol the item shall be annotated appropriately, such as“labeling not practical” or similar language.6.4 The placement of the label will not interfere with theoperation of the equipment.7. Keywords7.1 entity; equipment; identification label; placement; tagFI

18、G. 1 Entity Identification Labels Facing the UserFIG. 2 Entity Identification Label Placed on Front Right Side ofthe EquipmentFIG. 3 Entity Identification Label Attached to ToolE2631 09 (2015)2ASTM International takes no position respecting the validity of any patent rights asserted in connection wi

19、th any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible tech

20、nical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful considerat

21、ion at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Ha

22、rbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 09 (2015)3