ASTM E2466-2006 Standard Test Method for Colorimetry of Teeth Using Digital Still Camera Technology《利用数字静态摄影机实现牙齿比色法的标准试验方法》.pdf

《ASTM E2466-2006 Standard Test Method for Colorimetry of Teeth Using Digital Still Camera Technology《利用数字静态摄影机实现牙齿比色法的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM E2466-2006 Standard Test Method for Colorimetry of Teeth Using Digital Still Camera Technology《利用数字静态摄影机实现牙齿比色法的标准试验方法》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E 2466 06Standard Test Method forColorimetry of Teeth Using Digital Still Camera Technology1This standard is issued under the fixed designation E 2466; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last r

2、evision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.INTRODUCTIONTooth color is an important parameter used to ascertain certain medical and esthetic information.CIE colorimetric values fo

3、r the teeth are derived from the native RGB signals generated by a digitalstill camera, DSC, by broadband measurement of the reflectance of teeth. The illumination angle is 45degrees and CIELAB colorimetric coordinates are computed using equations contained in PracticeE 308. This test method, E 2466

4、, specifies the procedure used for the measurement of tooth colorin-vivo and in-vitro with illumination at 45 degrees relative to the sample plane which is also thenormal of the mouth, under an approximate equal energy spectrum. This test method is appropriate foranterior and posterior teeth.1. Scop

5、e1.1 This test method covers the procedure, instrumentalrequirements, standardization procedures, material standards,measurement procedures, and parameters necessary to makeprecise measurements of in-vivo tooth color and tooth white-ness. In particular it is meant to measure the color of teeth insel

6、ected human subjects.1.2 Digital images are used to evaluate tooth color of bothposterior and anterior dentition (teeth). All other non-relevantparts, such as gums, spaces, etc., must be separated from themeasurement and the analysis.All localized discoloration; suchas stains, inclusions, etc., may

7、be separated from the measure-ment and the analysis.1.3 The broadband reflectance factors of teeth are measured.The colorimetric measurement is performed with a digital stillcamera while using an illuminator(s) that provides controlledillumination on the teeth. The measured data from a digitalimage

8、are captured using a DSC. This test method is particu-larly useful for the gamut of tooth color which is:1.3.1 CIE L* from 55 to 95,1.3.2 CIE a* from 3 to 12,1.3.3 CIE b* from 8 to 25 units.1.4 The wavelengths for this test method include thatportion of the visible spectrum from 400 to 700 nm.1.5 Da

9、ta acquired using this test method is for comparativepurposes used during clinical trials or other types of research.1.6 This test method is designed to encompass natural teeth,artificial teeth, restorations, and shade guides.NOTE 1This procedure may not be applicable for all types of dentalwork.1.7

10、 The apparatus, measurement procedure, data analysistechnique are generic, so that a specific apparatus, measure-ment procedure, or data analysis technique may not be ex-cluded.1.8 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonl

11、y.1.9 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and to determine theapplicability of regulatory limitations prior to use.2. Reference

12、d Documents2.1 ASTM Standards:2D 2244 Practice for Calculation of Color Tolerances andColor Differences from Instrumentally Measured ColorCoordinatesE 179 Guide for Selection of Geometric Conditions forMeasurement of Reflection and Transmission Properties ofMaterialsE 284 Terminology of AppearanceE

13、308 Practice for Computing the Colors of Objects byUsing the CIE SystemE 313 Practice for Calculating Yellowness and WhitenessIndices from Instrumentally Measured Color Coordinates1This test method is under the jurisdiction of ASTM Committee E12 on Colorand Appearance and is the direct responsibilit

14、y of Subcommittee E12.06 on ImageBased Color Measurement.Current edition approved Jan. 15, 2006. Published March 2006.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer t

15、o the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.E 1345 Practice for Reducing the Effect of Variability ofColor Measurement by Use of Multiple MeasurementsE 1767 Practice for Sp

16、ecifying the Geometries of Observa-tion and Measurement to Characterize the Appearance ofMaterials2.2 ISO Publications:3ISO 17321-1, Colour characterization of digital still cam-eras (DSCs) Part 1: Stimuli, metrology, and test proce-dures2.3 ISCC Publications:4Technical Report 2003-1 Guide to Materi

17、al Standards andTheir Use in Color Measurement3. Terminology3.1 Terms and definitions in Terminology E 284 are appli-cable to this test method.3.2 DefinitionsTerms included in this section are peculiarto this standard.3.2.1 angle of incidence, nu1and optional u2, the polarangle between the central r

18、ay of the illuminator(s), I1and I2,and the Z axis which is normal to the camera. See Fig. A1.1.3.2.2 anterior teeth, nanterior teeth are the six upper andsix lower front teeth; the anterior teeth consist of incisors andcuspids (canines).3.2.3 bit depth, nthe number of digital bits used to storeinfor

19、mation contained in each pixel.3.2.3.1 DiscussionThe higher the depth, the more colorsare in an image. With 8 bit-per-channel color, there are a totalof 256 bits available for color representation in each of the R,G, B channels. RGB 8 bit-per-channel color is sometimescalled “24 bit color.”3.2.4 can

20、ine, nthe third tooth from the center of themouth towards the back of the mouth; these are the front teeththat have one rounded or pointed edge used for biting.3.2.5 facial surfaces, nof or toward the face, used todesignate the side of the tooth that is facing away from thetongue side.3.2.6 in-vitro

21、, adj or advin an artificial environmentoutside of the human body.3.2.7 in-vivo, adj or advwithin a living body; that is,measurements made of a living tooth in a living body.3.2.8 maxillary anterior teeth, nthe four front upperincisors and the canine teeth. See Fig. A1.5.3.2.9 native digital still c

22、amera spectral response function,nthe function relating scene radiance to image intensity of animaging system is called the digital still camera spectralresponse function.3.2.10 polarization, nthe orientation of the vibration pat-tern of light waves in a singular plane.3.2.11 polarizer filter, na co

23、mponent that blocks one ofthe two planes of vibration of an electromagnetic wave,producing linearly polarized light.3.2.11.1 DiscussionA polarizing filter can be used insunglasses to reduce glare.3.2.12 posterior teeth, nposterior teeth are the large teethin the back of the mouth.3.2.13 spatial whit

24、ening response, nthe evaluation ofcolor or color change used to determine unit dosing.4. Summary of Test Method4.1 This test method describes the procedures for broadbandreflectance measurement of teeth, in-vivo and in-vitro. Thestandardization of the instrumentation used to measure asubjects teeth

25、is defined. The basis for the selection ofspecimens and the measurement protocol given. The data fromthe reflectance measurements are converted to colorimetricvalues. The results are reported in terms of CIE tristimulusvalues, other colorimetric coordinate system values, and colo-rimetric indices.5.

26、 Significance and Use5.1 The light reflected from the facial anterior teeth can beused to calculate color coordinates. Monitored over time,changes in color can be observed. These data reveal informa-tion about the efficacy of a product, treatment study, orepidemiology of tooth color. For example, cl

27、inical studies ofconsumer tooth whitening systems evaluate the efficacy ofmanufacturers products.5.2 The change in color of the facial surfaces of anteriorteeth can be used to optimize the efficacy of tooth whiteningsystems. For example, the data can provide the answer thequestion: “What is the opti

28、mum percentage of whitening agentin a consumer tooth whitening system?”5.3 This procedure is suitable for use in research anddevelopment, marketing studies, comparative product analy-ses, and clinical trials.5.4 Prior research shows that a popular visual assessmentmethod of determining tooth color,

29、changes in tooth color, andwhiteness among clinicians yields less than desirable results(1-4). These assessment tools are designated “shade guides.”They consist of tooth-shaped, synthetic objects in the form ofteeth all of slightly different colors or different shades from oneanother. A “shade” is g

30、enerally regarded as a color slightlydifferent from a reference color (on a comparative basis). Thecolors of the synthetic teeth in these “shade guides” do notprogress linearly as observed visually or logically in a CIEcolorimetric coordinate system,5and they are metameric to realteeth.5.5 Transluce

31、ncyHuman teeth are translucent and thedegree of translucency varies widely between subjects. How-ever, translucency does not vary over the short term and is nottherefore a consideration in this test method.6. Interferences6.1 If the standard laboratory conditions listed in 6.2 changeduring the test

32、or from test to test by an appreciable amount,these conditions may cause interferences, and the accuracy and3Available from International Imaging Industry Association (I3A), 701Westchester Avenue, Suite 317W, White Plains, NY 10604, 914-285-4933,isotc42i3a.org.4Available from ISCC, Inter-Society Col

33、or Council, 11491 Sunset Hills Rd.,Reston, Va, 20190.5Available from University of Michigan, http:/www.lib.umich.edu/dentlib/Dental_tables/Colorshadguid.html.E2466062precision requirements of this test method may not beachieved. In some cases these effects may only be observedduring the performance

34、of the test.6.2 Factors Effecting Test ResultsThe following factorsare known to affect the test results.6.2.1 Environmental:6.2.1.1 Extraneous RadiationExtraneous light from othersources and near-infrared (NIR) radiations must be shieldedfrom the test apparatus.6.2.1.2 VibrationsMechanical oscillati

35、ons that causecomponents of the apparatus to move independently from oneanother may cause errors in test results.6.2.1.3 Thermal ChangesTemperature changes occurringduring a test or differences in temperature between testinglocations may affect the reflectance factor of the standardiza-tion, calibra

36、tion, and verification plaques, and the apparatusspectral response function.6.2.1.4 Power Input FluctuationsLarge changes in theline frequency or supply voltage may cause the apparatus toreport erroneous results.6.2.2 RetractorsThe surface finish of the retractors affectsthe experimental test result

37、s. It has been determined that aneutral (clear) finish on the surface of the retractors mayintroduce a bias into the test results.6.3 StandardizationThe system must allow for successfulstandardization.6.4 Equipment OperationIf the system cannot be stan-dardized, a series of checks must be performed

38、(lighting,camera, etc.) to identify the reason. The component of thesystem in error will be adjusted or replaced to bring the systemback into calibration.6.5 Controlling Factors:6.5.1 These interferences may be eliminated and problemsavoided by controlling and regulating each factor within theconstr

39、aints of the allowable experimental error. The values andlimits for these factors are typically determined experimentally.7. Apparatus7.1 GeneralThe components described in this section aredescribed generically. The intention is not to exclude anycomponent from being used, or to exclude any type ofi

40、nstrument that may be available commercially. Between 4 and6 different components or component assemblies are requiredto accomplish the measurement.7.2 GeometryThe geometry of the system is 45:0 asdescribed in Practice E 1767 and Guide E 179. The DSCSystem Geometry (Coordinate System) and Angular Co

41、nven-tion are shown in Fig. A1.1.7.3 ComponentsA block diagram of these componentassemblies is shown diagrammatically in Fig. A1.2.7.3.1 Source Illumination AssemblyContains the sourceof illumination and associated optics to produce irradiance, E,on the sample over a specified spot area, designated

42、A. Thesource is broadband and continuous in nature. A diagrammaticrepresentation of the components of a typical Source Illumi-nation Assembly Unit is shown in Fig. A1.3.7.3.2 Source Beam(s)A collimated or slightly convergingbeam(s) focused on the sample plane. Since the shape andposition of the spec

43、imens being measured vary widely, a smallconvergence angle minimizes local variations in intensity. Twobeams located at 45 relative to the normal of the sample planeare required to examine posterior teeth (on each side of themouth) and to achieve the uniformity requirements.7.3.3 PositionTypically t

44、he Source Illumination Assem-blies are in a fixed position relative to the sample (Subject)holder and the DSC. Therefore, small variations in u areminimized. The angle u is the subtended angle between theSource Illumination Assembly Units and the DSC. Refer toFig. A1.1.7.3.4 Source Optical ElementsT

45、he optical elements mustcondition the radiation from the source so that it is spatiallyuniform within 610 %. The distance, d, from the DSC to thesample plane must be selected to maintain the uniformityrequirements. Refer to Fig. A1.6.7.3.5 Spectral Power DistributionThe exact spectral na-ture of the

46、 illuminator is immaterial for the measurement ofteeth and non-fluorescent specimens so long as the source isstable with time and has adequate energy at all wavelengths inthe region required for measurement.An approximation to D50provides an equal energy spectrum over the area of interest forDSCs. C

47、ommonly used light sources include incandescentlamps, either operated without filters or filtered to simulatestandard illuminants, flashed or continuous-wave xenon-arclamps and discrete pseudo-monochromatic sources, such aslight emitting diodes (LEDs).7.3.6 PolarizationThe linear polarizer provides

48、and con-trols the polarization state of the incident light. This polarizeron the illuminators plus a cross polarizer filter on the lenssystem of the DSC eliminates glare caused by reflection of thesubjects teeth during imaging. Wavelength range, extinctionratio, transmittance, and beam deviation are

49、 important param-eters and must be selected.7.3.7 Heat Rejection FiltersThese filters remove undes-ired near-infrared (NIR) radiation including heat that adverselyaffects the subject and provide spectral shaping of the spectralpower distribution of the source illumination.7.3.8 Selective Blue FiltersThese filters condition thespectral power distribution of the illumination so that thespectral power distribution is similar to an approximate equalenergy spectrum, such as illuminant D50.7.4 Sample Plane HolderThe sample plane holder pro-vides a