ASTM E1449-1992(2011) Standard Guide for Supercritical Fluid Chromatography Terms and Relationships《超临界液相色谱法术语和关系指南》.pdf

《ASTM E1449-1992(2011) Standard Guide for Supercritical Fluid Chromatography Terms and Relationships《超临界液相色谱法术语和关系指南》.pdf》由会员分享，可在线阅读，更多相关《ASTM E1449-1992(2011) Standard Guide for Supercritical Fluid Chromatography Terms and Relationships《超临界液相色谱法术语和关系指南》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E1449 92 (Reapproved 2011)Standard Guide forSupercritical Fluid Chromatography Terms andRelationships1This standard is issued under the fixed designation E1449; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year

2、of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This guide deals primarily with the terms and relation-ships used in supercritical fluid chromatography.1.2 Since m

3、any of the basic terms and definitions also applyto gas chromatography and liquid chromatography, this guideis using, whenever possible, symbols identical to PracticesE355 and E682.1.3 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstan

4、dard.2. Referenced Documents2.1 ASTM Standards:2E355 Practice for Gas Chromatography Terms and Rela-tionshipsE682 Practice for Liquid Chromatography Terms and Rela-tionships3. Names of Techniques3.1 Supercritical Fluid Chromatography, abbreviated asSFC, comprises all chromatographic methods in which

5、 boththe mobile phase is supercritical under the conditions ofanalysis and where the solvating properties of the fluid have ameasurable affect on the separation. Early work in the field wasperformed under a broader headingdense gas chromatogra-phy. Related work in the field uses subcritical or near-

6、criticalconditions to affect separation.3.2 Separation is achieved by differences in the distributionof the components of a sample between the mobile andstationary phases, causing them to move through the column atdifferent rates (differential migration).3.3 In supercritical fluid chromatography, th

7、e pressure maybe constant or changing during a chromatographic separation.3.3.1 Isobaric is a term used when the mobile phase is keptat constant pressure. This may be for a specified time intervalor for the entire chromatographic separation.3.3.2 Programmed Pressure Supercritical Fluid Chroma-tograp

8、hy is the version of the technique in which the columnpressure is changed with time during the passage of the samplecomponents through the separation column. Isobaric intervalsmay be included in the pressure program.3.4 In supercritical fluid chromatography, the temperaturemay be constant, or changi

9、ng during a chromatographicseparation.3.4.1 Isothermal Supercritical Fluid Chromatography isthe version of the technique in which the column temperatureis held constant during the passage of the sample componentsthrough the separation column.3.4.2 Programmed Temperature Supercritical Fluid Chro-mato

10、graphy is the version of the technique in which thecolumn temperature is changed with time during the passage ofthe sample components through the separation column. Iso-thermal intervals may be included in the temperature program.3.5 In supercritical fluid chromatography, the density maybe constant

11、or changing during the chromatographic separa-tion.3.5.1 Isoconfertic is a term used when the density of themobile phase is kept constant for a specified time or for theentire chromatographic separation.3.5.2 Programmed Density Supercritical Fluid Chromatog-raphy is the version of the technique in w

12、hich the columndensity is changed with time during the passage of the samplecomponents through the separation column. Isoconfertic inter-vals may be included in the density program.3.5.3 Flow Programming is a technique where the mobilephase linear velocity is changed during the chromatographicproced

13、ure. However, with fixed orifice restrictors, flow pro-gramming is more complex requiring an increase in pressure toeffect an increase in linear velocity.3.6 In supercritical fluid chromatography, the compositionof the mobile phase may be constant or changing during achromatographic separation.1This

14、 guide is under the jurisdiction of ASTM Committee E13 on MolecularSpectroscopy and Separation Science and is the direct responsibility of Subcom-mittee E13.19 on Separation Science.Current edition approved Nov. 1, 2011. Published December 2011. Originallyapproved in 1992. Last previous edition appr

15、oved in 2006 as E1449 92 (2006).DOI: 10.1520/E1449-92R11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Cop

16、yright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.6.1 The term Isocratic is used when the composition ofthe mobile phase is kept constant during a chromatographicseparation.3.6.2 The term Gradient Elution is used to specify thetechnique

17、when a deliberate change in the mobile phasecomposition is made during the chromatographic procedure.Isocratic intervals may be included in the gradient program.4. Apparatus4.1 PumpsThe function of the pumps is to deliver themobile phase at a controlled flow rate to the chromatographiccolumn.4.1.1 S

18、yringe Pumps have a piston that advances at acontrolled rate within a smooth cylinder to displace the mobilephase.4.1.2 Reciprocating Pumps have a single or dual chamberfrom which mobile phase is displaced by reciprocating pis-ton(s) or diaphragm(s).4.2 Sample Inlet Systems represent the means for i

19、ntroduc-ing samples into the columns.4.2.1 Direct Injection is a sample introduction techniquewhereby the entire volume of sample is swept onto the head ofthe analytical column. Its use is most prevalent in packedcolumn SFC.4.2.2 Split-Flow Injection introduces only a portion of thesample volume ont

20、o the analytical column so as to preventoverloading of the column in open tubular SFC. This isachieved by the use of a splitter tee or similar contrivance, suchthat the incoming slug of sample is divided between theanalytical column and a flow restrictor vented to waste. Theamount of sample deposite

21、d on the column is a function of theratio of the flow to the column versus the flow through thisrestrictor. This ratio can thus be adjusted for different samplesand column capacities.4.2.3 Timed-Split (Moving-Split) Injection achieves thesame end result as split-flow injection. The volume of samplei

22、ntroduced onto the column is governed by the rapid back-and-forth motion of an internal-loop sample rotor in a valve. Thetime interval between the two motions determines the volumeof sample injected, with shorter times delivering smallervolumes.4.2.4 On-Line Supercritical Extraction is a means of di

23、-rectly introducing a sample or portion of a sample into asupercritical fluid chromatograph. The sample is placed in anextraction cell and extracted with the supercritical fluid. Theextraction effluent containing the solutes of interest are ulti-mately transferred to the column by the action of swit

24、ching orsampling valves. This can be accomplished with or withoutsolute focusing (that is, using a suitable trap such as acryogenic trapping).4.3 Columns consist of tubes that contain the stationaryphase and through which the supercritical fluid mobile phaseflows.4.3.1 Packed Column Supercritical Fl

25、uid Chromatogra-phy uses an active solid or a liquid that is chemically bondedto a solid and packed into a column, generally stainless steel orfused silica; as the stationary phase.4.3.2 Wall-Coated Open-Tubular Supercritical Fluid Chro-matography uses a liquid that is chemically bonded to the wallo

26、f an open-tubular column as stationary phase. Fused silicatubing columns, internal diameter (i.d.) 100 m, may shatterat pressures employed in SFC.Ahigh degree of crosslinking isdesirable to reduce stationary phase solubility in the mobilephase.4.4 Restrictors are devices employed to maintain the pre

27、s-sure in the chromatographic system. The pressure of thesupercritical fluid is usually reduced to ambient after passagethrough the restrictor.The mobile phase flow rate is determinedby the restrictor dimensions or operation. The restrictor isplaced before some types of detectors (for example, flame

28、ionization, mass spectrometer) and after other types of detec-tors (for example, UV).4.4.1 A Linear Restrictor is a length of small i.d. tubing ofuniform bore. Linear restrictors are made of polyimidecoatedfused silica tubing, or stainless steel or other tubing of theappropriate diameter. The amount

29、 of restriction provided isdependent upon both the length and i.d. of the tubing.4.4.2 A Tapered Restrictor is a length of small i.d. tubingwhere one end has been reduced by drawing in a flame in thecase of fused silica tubing, or crimped in the case of metaltubing.4.4.3 An Integral Restrictor (1)3c

30、onsists of a length offused silica tubing with one end closed by heating with amicrotorch. This closed end is then ground until a hole with thedesired initial linear velocity is obtained.4.4.4 A Converging-Diverging Restrictor (2) has the wall ofthe tubing collapsed slightly near one end forming a c

31、onstric-tion. This constriction is similar to a venturi in profile and thepoint of smallest diameter is located about 1 to 2 mm from theend of the tubing.4.4.5 An Orifice is a type of restrictor which uses a metaldisk or diaphragm with an appropriately sized opening. Thistype normally requires an ad

32、apter or holder specifically de-signed to couple the device to a detector.4.4.6 A Porous Frit Restrictor4consists of a length of fusedsilica tubing containing a porous plug at one end.4.4.7 A Back Pressure Regulator consists of a diaphragmvalve which can be adjusted to control the pressure maintaine

33、don its inlet (instrument) side. The outlet discharge pressure isnominally one atmosphere.4.5 Detectors are devices that respond to the presence ofeluted solutes in the mobile phase emerging from the column.Ideally, the response should be proportional to the mass orconcentration of solute in the mob

34、ile phase. Detectors may bedivided either according to the type of measurement or theprinciple of detection.4.5.1 Differential Concentration Detectors measure theproportion of eluted sample component(s) in the mobile phasepassing through the detector. The peak area is inverselyproportional to the mo

35、bile phase flow rate.3The boldface numbers in parentheses refer to a list of references at the end ofthis standard.4Cortez, H., Pfeiffer, C., Richter, B., and Stevens, T. U. S., Patent No. 4 793 920,1988.E1449 92 (2011)24.5.2 Differential Mass Detectors measure the instanta-neous mass of a component

36、 within the detector per unit time(g/s). The area under the curve is independent of the mobilephase flow rate.5. Reagents5.1 Supercritical Fluid is a fluid state of a substance inter-mediate between a gas and a liquid. A supercritical fluid maybe defined from the accompanying phase diagram (Fig. 1).

37、 Thesupercritical fluid region is defined by temperatures andpressures, both above the critical values. A subcritical fluid (orliquid) is a compound that would usually be a gas at ambienttemperature but is held as a liquid by the application ofpressure below its supercritical point.5.1.1 The Critica

38、l Temperature is the temperature abovewhich a substance cannot be liquefied or condensed no matterhow great the applied pressure.5.1.2 The Critical Pressure is the pressure that would justsuffice to liquefy the fluid at its critical temperature.5.1.3 The Reduced Pressure is the ratio of the workingp

39、ressure to the critical pressure of the substance.5.1.4 The Reduced Temperature is the ratio of the workingtemperature to the critical temperature of the substance.5.1.5 The Density of a supercritical fluid (the weight per unitvolume of the fluid) in chromatographic separations is calcu-lated from a

40、n empirical equation of state.5.2 A Modifier or co-solvent is a substance added to asupercritical fluid to enhance its solvent strength, usually byincreasing the polarity of the mobile phase, or binding to activesites on a stationary phase.5.3 The Stationary Phase is composed of the active immo-bile

41、 materials within the column that selectively retard thepassage of sample components. Inert materials that merelyprovide physical support or occupy space within the columnsare not part of the stationary phase.NOTE 1Extremely porous stationary phases may exhibit exclusionphenomenon in addition to ads

42、orptive interactions.5.3.1 An Interactive Solid is a stationary phase material withbulk homogeneity where the surface effects separation byadsorptive interactions. Examples are silica and alumina.5.3.2 A Bonded Phase is a stationary phase that has beencovalently attached to a solid support. The samp

43、le componentspartition between the stationary and mobile phases whichresults in separation. Octadecylsilyl groups bonded to silica gelparticles and polydimethylsiloxane (or dimethyl polysiloxane)bonded to deactivated fused silica column wall representexamples for packed column and open tubular colum

44、n phases,respectively.5.4 The Solid Support is the inert material that holds thestationary phase in intimate contact with the mobile phase. Itmay consist of porous or impenetrable particles or granules orthe interior wall of the column itself, or a combination of these.5.5 The Column Packing consist

45、s of all the material used tofill packed columns, including the solid support and the bondedphase or the interactive solid.5.6 Solutes are the sample components that are introducedinto the chromatographic system and are transported by themobile phase and elute through the column. Some solutes maybe

46、unretained.6. Readout6.1 A Chromatogram is a plot of detector response againsttime or effluent volume. Idealized chromatograms obtainedwith a differential detector for an unretained substance and oneother component are shown in Fig. 2.6.2 The definitions in 6.2.1-6.2.6 apply to chromatogramsobtained

47、 directly by means of differential detectors or indi-rectly by differentiating the response of integral detectors.6.2.1 ABaseline is that portion of a chromatogram where nodetectable sample components emerge from the column.6.2.2 A Peak is that portion of a chromatogram where asingle detectable comp

48、onent, or two or more unresolveddetectable components, elute from the column.6.2.3 The Peak Base,CDinFig. 2, is the interpolation of thebaseline between the extremities of a peak.6.2.4 The Peak Area, CHFEGJD in Fig. 2, is the areaenclosed between the peak and the peak base.6.2.5 Peak Height,EBinFig.

49、 2, is the perpendiculardistance measured in the direction of detector response, fromthe peak base to peak maximum.6.2.6 Peak Widths represent retention dimensions parallelto the baseline. Peak width at base or base width, KL in Fig. 2,is the retention dimension of the peak base intercepted by thetangents drawn to the inflection points on both sides of thepeak. Peak width at half height, HJ in Fig. 2, is the retentiondimension drawn at 50 % of peak height parallel to the peakFIG. 1 Phase Diagram FIG. 2 Typical ChromatogramE1449 92 (2011)3base. The peak width at inflection poin