ASTM E1096-1986(2018) 6250 Standard Specification for Laboratory Glass Separatory Funnels《实验室玻璃分液漏斗的标准规格》.pdf

《ASTM E1096-1986(2018) 6250 Standard Specification for Laboratory Glass Separatory Funnels《实验室玻璃分液漏斗的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM E1096-1986(2018) 6250 Standard Specification for Laboratory Glass Separatory Funnels《实验室玻璃分液漏斗的标准规格》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E1096 86 (Reapproved 2018)Standard Specification forLaboratory Glass Separatory Funnels1This standard is issued under the fixed designation E1096; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revisi

2、on. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.INTRODUCTIONSeparatory funnels are used in laboratories primarily for liquid extractions, and are intended tofacilitate the separation of two

3、 immiscible liquids of different densities into separate layers. Somefunnels are used to add reagent solution into a reaction vessel. They are, therefore, often provided witha tapered ground joint at the bottom of the delivery stem for joining to vessels having similarly taperedground necks. They ma

4、y also be provided with pressure equalizing side arms.1. Scope1.1 This specification provides standard dimensional re-quirements for glass separatory funnels for general laboratoryuse.1.2 This international standard was developed in accor-dance with internationally recognized principles on standard-

5、ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2E438 Specification for Glasses in Laboratory Appar

6、atusE671 Specification for Maximum Permissible Thermal Re-sidual Stress in Annealed Glass Laboratory ApparatusE675 Specification for Interchangeable Taper-Ground Stop-cocks And StoppersE676 Specification for Interchangeable Taper-Ground JointsE694 Specification for Laboratory Glass Volumetric Appa-r

7、atusE911 Specification for Glass Stopcocks with Polytetrafluo-roethylene (PTFE) Plugs3. Classification3.1 Separatory funnels shall be in the following types andsizes:3.1.1 Type 1ACylindrical shape with open top.3.1.1.1 Sizes60, 125, and 250 cm3.3.1.2 Type 1BCylindrical with stopper finish top.3.1.2.

8、1 Sizes60, 125, 250, 500, and 1000 cm3.3.1.3 Type 1CCylindrical with stopper finish top, gradu-ated.3.1.3.1 Sizes125, 250, 500, and 1000 cm3.3.1.4 Type 2Globe shape with stopper finish top.3.1.4.1 Sizes60, 125, 250, 500, 1000, 2000, and 4000 cm3.3.1.5 Type 3Globe shape, “French,” with stopper finish

9、top.3.1.5.1 Sizes125, 250, 500, and 1000 cm3.3.1.6 Type 4Pear shape, Squibb, with stopper finish top.3.1.6.1 Sizes20, 60, 125, 250, 500, 1000, 2000, and 4000cm3.NOTE 1The term millilitre (mL) is commonly used as a special namefor the cubic centimetre (cm3) and similarly the litre (L) for 1000 cubicc

10、entimetres, in accordance with the International System of Units (SI).4. Materials and Annealing4.1 Separatory funnels shall be made of borosilicate glassconforming to the requirement of Type 1, Class A of Specifi-cation E438.4.2 Maximum residual thermal stress shall be such as toconform to Specific

11、ation E671.5. Design5.1 Type 1 cylindrical separatory funnels shall have straightsides and comply with the dimensions given in Table 1. (Type1A stem length shall comply with Table 2.) See Fig. 1, Type1A; 1B; and 1C.5.2 Type 2 globe-shaped separatory funnels shall be roughlyglobular in shape and have

12、 dimensions complying with thosegiven in Table 2. See Fig. 2, Type 2.1This specification is under the jurisdiction of ASTM Committee E41 onLaboratory Apparatus and is the direct responsibility of Subcommittee E41.01 onLaboratory Ware and Supplies.Current edition approved Jan. 1, 2018. Published Janu

13、ary 2018. Originallyapproved in 1986. Last previous edition approved in 2011 as E1096 86 (2011)DOI: 10.1520/E1096-86R18.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer

14、 to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization establishe

15、d in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.15.3 Type 3 separatory funnels shall be like Type 2, however,a straight-walled portion shall be between the glo

16、be and thestopcock assembly and shall meet the dimensions listed inTable 2, except for stem length which shall have a maximumlength of 40 mm. See Fig. 2, Type 3.5.4 Type 4 Squibb separatory funnels shall be pear-shapedor conical-shaped and meet the requirements of Table 3. SeeFig. 2, Type 4.5.5 Type

17、 1 and 4 separatory funnels may be supplied with ataper-ground joint below the stopcock, (see Specification E676and Fig. 1C. Type 1 funnels with this feature may also havepressure equalizing tubes placed at the back or opposite side ofthe funnel when it is in the position of normal use with thehandl

18、e of the stopcock on the right. See Fig. 1B).5.6 All types except Type 1A shall have stoppers or betaper-ground to receive stoppers in accordance with Specifica-tions E675 or E676. Stoppers of suitable inert plastic materialmay be permitted as an alternative to glass but must alsocomply with Specifi

19、cation E675. All stoppers shall bear a sizeidentification.5.7 All types shall have stopcock assemblies. They shall bedesigned to permit smooth and precise control of outflow andto meet the permissible leakage rate requirements allowed inSpecification E675. Stopcocks shall be made of glass or fromsui

20、table inert plastic material such as polytetrafluoroethylene(PTFE) and must comply with Specification E911, or form aseal by having PTFE plug ends butt against a constriction in theglass shell.FIG. 1 Cylindrical Body FunnelsType 2 Type 3 Type 4FIG. 2 Globe and Squibb-Pear Shaped Body FunnelsTABLE 1

21、Cylindrical Body FunnelsNominal Capacity,mL 60 125 250 500 1000Body height, max 135 200 225 290 390(mm) (see Fig.1“L1”)Body diameter, 34 44 53 67 79max (mm)Body wall thick- 0.8 0.8 0.9 0.9 1.3ness, min (mm)Stem length, max 100 100 100 100 100(mm) (see Fig.1“S1”)Stem diameter, 12 12 12 12 12max (mm)S

22、tem wall thick- 1.5 1.5 1.5 1.5 1.5ness min (mm)Stopcock size 2 2 2 4 4Stopper size 16 22 22 27 27Stem taper- 14/20 24/40 24/40 24/40 .ground jointE1096 86 (2018)25.8 Delivery stems for Types 1B and C, 3, and 4 should havea bore wide enough to avoid formation of a liquid column, thatcould lead to un

23、satisfactory separation. Type 1A and Type 2funnel stems shall conform to stem dimensions of Table 2.Stem tip shall be at an angle of 30 or 45.6. Graduations6.1 Type 1C separatory funnels shall have a graduated scaleplaced centrally about the vertical axis of the funnel when it isin position of norma

24、l use with the handle of the stopcock on theright. See Table 4 for specifications. (For graduation patternand figuring see Specification E694.)6.1.1 The graduation marks may be figured in ascendingorder or in both ascending and descending order.6.1.2 Subdivision and numbering shall conform to Table

25、4.7. Markings7.1 Each separatory funnel shall be permanently markedwith the name or known trademark of the manufacturer, orboth, the nominal capacity, except for graduated cylindricalfunnels, and the symbol cm3, mL, or L.8. Keywords8.1 funnels; glass; separatoryASTM International takes no position r

26、especting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.Thi

27、s standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM Inte

28、rnational Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown

29、below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-95

30、55 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 2 Globe Shaped Body FunnelsNominal Capacity, (mL) 3

31、0 60 125 250 500 1000 2000 4000Body height, max (mm) (see Fig. 2 “L2”) 75 85 110 135 175 215 255 290Body diameter, max (mm) 50 55 70 90 110 140 170 210Body wall thickness, min (mm) 0.8 0.8 0.8 0.9 0.9 1.3 1.3 1.3Straight wall length, max (mm) (Type 3 only) (see Fig. 2 “S3”) 110 130 130 130 135 140 1

32、65 .Straight wall diameter, max (mm) (Type 3 only) 18 18 18 18 25 35 35 .Stem length, max (mm)A(see Fig. 2“ S2”) 180 180 180 180 180 180 135 135Stem diameter, max (mm) 12 12 12 12 12 12 14 15Stem wall thickness, min (mm) 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5Stopcock size 2 2 2 2 4 4 6 8Stopper size 16 16

33、22 22 27 27 38 38AType 3 50 mm max.TABLE 3 Squibb Pear Shaped Body FunnelsNominal Capacity, (mL) 30 60 125 250 500 1000 2000 4000Body height, max (mm) (see Fig. 2 “L4”) 85 140 160 200 225 255 340 480Body diameter, max (mm) 45 60 65 80 105 125 155 210Body wall thickness, min (mm) 0.8 0.8 0.8 0.9 0.9

34、1.0 1.3 1.3Stem length, max (mm) (see Fig. 2 “S4”) 75 75 75 75 75 75 75 75Stem diameter, max (mm) 12 12 12 12 12 12 14 15 or 19AStem wall thickness, min (mm) 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5Stopcock size 2 2 2 2 or 4 4 4 6 8 or 10AStopper size 9 or 13 16 22 22 27 27 38 38Stem taper-ground joint . . 14/20,19/22or 24/4024/40 24/40 24/40 . .TABLE 4 Graduated Cylindrical Body FunnelsNominal Capacity(mL)50 100 125 250 500 1000Subdivision (mL) 5 5 1 2 or 5 5 10Numbered at leastat every milli-litre10 10 10 20 or 50 50 100E1096 86 (2018)3