ASTM E329-2013c 9595 Standard Specification for Agencies Engaged in Construction Inspection Testing or Special Inspection《施工检验 测试或专项检验从业机构的标准规范》.pdf

《ASTM E329-2013c 9595 Standard Specification for Agencies Engaged in Construction Inspection Testing or Special Inspection《施工检验 测试或专项检验从业机构的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM E329-2013c 9595 Standard Specification for Agencies Engaged in Construction Inspection Testing or Special Inspection《施工检验 测试或专项检验从业机构的标准规范》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E329 13c An American National StandardStandard Specification forAgencies Engaged in Construction Inspection, Testing, orSpecial Inspection1This standard is issued under the fixed designation E329; the number immediately following the designation indicates the year oforiginal adoption or

2、, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Sc

3、ope*1.1 This specification defines the minimum requirements foragencies engaged in:(a) Inspection of construction activities and materials usedin construction,(b) Testing of construction activities and materials used inconstruction, and(c) Special Inspection.1.2 Criteria are provided for assessing t

4、he competence of anagency to properly perform designated inspections, tests, orSpecial Inspection services. This specification establishes es-sential characteristics pertaining to the organization,management, personnel, facilities, quality systems,responsibilities, duties, inspection and testing met

5、hods,records, and reports of the agency. This specification may besupplemented by more specific criteria and requirements, ifrequired.1.2.1 This specification specifically addresses factors rel-evant to an agencys ability to produce precise, accurate testdata or determine the conformity of construct

6、ion activities andmaterials used in construction with regulations, codes,standards, and approved project plans and specifications con-taining the requirements against which the inspection or test, orboth, will be performed. Specific or general requirementsinclude:1.2.1.1 Facilities and management of

7、 the agency,1.2.1.2 Sufficiency and technical competency of personnel,1.2.1.3 Suitability, calibration, and maintenance ofequipment,1.2.1.4 Quality system, audit, and review,1.2.1.5 Responsibilities, duties, and authority of agencies,1.2.1.6 Validity and appropriateness of sampling, testing,and insp

8、ection methods and procedures,1.2.1.7 Management of records,1.2.1.8 Reporting, review, and transmission of test andinspection data or findings, and1.2.1.9 Specific requirements for identified fields (concrete,soil, etc.).1.3 This specification can be used as a basis to assess anagency and is intende

9、d for use in accrediting agencies, publicor private, engaged in inspection, testing, and Special Inspec-tion of construction activities and materials used in construc-tion. These services include but are not limited to reinforcedconcrete, precast concrete, structural steel erection, welding,bolting,

10、 soil and rock, foundations, masonry, sprayed fire-resistive materials, fire stops, exterior insulation and finishsystem (EIFS), and Special Cases. Building officials can useSpecification E329 to assess the competency of agencies in thefields covered by Specification E329.1.4 A certificate of accred

11、itation, including the scope ofaccreditation, is required to comply with this specification.1.5 The users of an accredited agency must review theagencys scope of accreditation to ensure the agency has beenaccredited for its technical competence to perform the specificinspections or tests requested b

12、y the user.1.6 This specification is not intended to:(a) circumvent or replace the agreement between theagency and the owner that should clearly define the responsi-bilities and authorities of the agency;(b) address design requirements that supersede applicablecodes, laws, and regulations; or(c) add

13、ress construction means, methods, techniques, orsequences.2. Referenced Documents2.1 ASTM Standards:2A880 Practice for Criteria for Use in Evaluation of Testing1This specification is under the jurisdiction of ASTM Committee E36 onAccreditation the data are used to evaluate ordetermine selected prope

14、rties or characteristics of the activitiesor materials.4. Significance and Use4.1 The inspection and testing of construction activities andthe materials used in construction are important elements inobtaining quality construction in general compliance with thecontract documents. An agency providing

15、constructioninspection, testing, or Special Inspection, must be selected withcare after a comprehensive evaluation of their competency toperform the services properly and in compliance with theapproved project plans and specifications.4.2 This specification provides minimum criteria for use inassess

16、ing the qualifications of construction inspection, testing,and Special Inspection agencies. The criteria may be supple-mented by more specific criteria and requirements for particu-lar classes of testing or types of inspection agencies. Anindividual user can also use it to judge the competency of an

17、agency.4.3 The intent of this specification is to provide a standard-ized basis for requirements for a technically oriented construc-tion inspection, testing, or Special Inspection agency, withrespect to the agencys capability to objectively and compe-tently provide the specific services without pre

18、judice.4.4 Typically, assessing an agency involves the followingthree essential sequential phases:4.4.1 Submittal of basic information in accordance with thecriteria of this specification to the accreditation body by anagency desiring to be accredited to this specification,4.4.2 Assessment of the ag

19、ency-submitted information bythe accreditation body, andE329 13c34.4.3 On-site assessment of the agency by the accreditationbody.5. Organization and Management5.1 The agency shall be legally identifiable. It shall beorganized and shall operate in such a way that its facilities meetthe requirements o

20、f this specification.5.1.1 Main facilities, sub-facilities, and permanent site fa-cilities shall maintain personnel, equipment, procedures, anddocumentation as required in this specification. The managerfor the main facility may also be responsible for a sub-facilityor permanent site facility (see 6

21、.2.2 and 6.3.2). Main facilities,sub-facilities, and permanent site facilities shall be accreditedin accordance with 9.4.1 to perform the functions described in3.1.2.1 or 3.1.2.3 or 3.1.2.5 of this specification.5.1.2 Temporary site facilities offering a defined scope ofservices for a specific proje

22、ct, which are demonstrably underthe main facilitys or sub-facilitys technical direction andquality program, do not require separate accreditation. Agen-cies that use temporary site facilities for their projects shalldescribe the operation of these facilities in their qualitymanual.5.1.3 An endorseme

23、nt for the operation of temporary sitefacilities shall also be listed on the agencys accreditationcertificate.5.2 The agency shall:5.2.1 Have managerial personnel with the authority andresources needed to discharge their duties.5.2.2 Have arrangements to ensure that its personnel are freefrom any co

24、mmercial, financial, and other pressures includingtrade organization rules that might adversely affect theirindependence, their judgment, and the integrity of their ser-vices. A Special Inspection agency or its personnel shall not bedirectly involved in the manufacture, supply, installation, use,or

25、maintenance of the inspected items.5.2.3 Be organized in such a way that confidence in itsindependence of judgment and integrity is maintained at alltimes.5.2.4 Specify and document the responsibility, authority,qualifications, and interrelation of all personnel who manage,perform, or verify service

26、s affecting the quality of inspectionsor tests, or both.5.2.5 Provide supervision by persons qualified to performthe inspections and tests and to implement relevant procedures.They shall be qualified to evaluate the objective of theinspections or tests and the results. The ratio of supervisory tonon

27、-supervisory personnel shall be such as to ensure adequatesupervision.5.2.6 Have a technical manager (however named) who hasoverall responsibility for the technical operations.5.2.7 Have a quality manager (however named) who has theresponsibility for the quality system and its implementation.The qua

28、lity manager shall have direct access to the highestlevel of management at which decisions are made on agencypolicy or resources, and to the technical manager. In someagencies, the quality manager may also be the technicalmanager or deputy technical manager.5.2.8 Nominate deputies in case of absence

29、 of the technicalor quality manager.5.2.9 Where relevant, have documented policy and proce-dures to ensure the protection of clients confidential informa-tion and proprietary rights.5.2.10 Where appropriate, as determined by the agencysquality manual, participate in interlaboratory comparisons andpr

30、oficiency testing programs.6. Personnel6.1 General6.1.1 The agency shall have sufficient personnel having thenecessary education, training, technical knowledge, certifica-tion as appropriate, and experience for their assigned functions.6.1.2 The agency shall ensure that the training of itspersonnel

31、is kept up-to-date.6.1.3 Records of relevant certification, qualifications,training, skills, and experience of the technical personnel shallbe maintained by the agency.6.2 Construction Inspection and Testing Agency6.2.1 The following personnel requirements must be satis-fied by the agency when inspe

32、ction or testing services, or both,are being provided:6.2.2 The inspection and testing services of the agency thatprovides the quality control or quality assurance program, orboth, as related to construction activities or materials used inconstruction, shall be under the direction of a person charge

33、dwith engineering managerial responsibility. The person shall bea licensed/registered design professional and a full-time em-ployee of that agency. The person shall have at least five yearsexperience in inspection and testing of construction activitiesand materials used in construction. The organiza

34、tion mayconsist of one or more separate facilities providing inspectionor testing services or both. A licensed/registered design pro-fessional may have engineering managerial responsibility forone or more facilities within the organization.6.2.3 When a producers or manufacturers laboratory onlyserve

35、s as a quality control laboratory and does not producetests for acceptance, payment, or the official record, therequirement for a registered professional is waived. However,the laboratory function of the organization shall be supervisedby a quality control manager. The quality control manager shallh

36、ave at least five years experience in testing of that particularconstruction material, and be a full time employee of theorganization. The quality control manager will have the au-thority to make changes in production to ensure that qualitymaterial is produced. He may serve as the quality controlman

37、ager for several materials production facilities. The qualitycontrol manager shall have the certifications appropriate to thetesting of the materials supervised.6.2.4 A laboratory supervisor shall have at least three yearsexperience performing tests in relevant construction activitiesand materials u

38、sed in construction. This person shall be able todemonstrate either by oral or written examination, or both,their ability to perform the tests normally required in themanner stipulated under ASTM or other governing test proce-dures and shall be capable of evaluating the test results in termsE329 13c

39、4of specification compliance. Certification by qualified national,regional, or state authorities as appropriate to the services isrequired.6.2.5 A field supervisor shall have at least three yearsinspection experience in the type of services being supervised.This person shall be able to demonstrate,

40、either by oral orwritten examination, or both, their ability to perform correctlythe required duties and shall be capable of evaluating theinspection or test results in terms of specification compliance.Certification by qualified national, regional, or state authoritiesas appropriate to the services

41、 is required.6.2.6 Inspector or TechnicianThis person shall have suf-ficient education and on-the-job training or trade schooltraining to properly perform the inspection or test to which theperson is assigned. This person must be able to demonstratecompetence for the test or inspection that is being

42、 conductedeither by oral or written examination, or both. Certification asappropriate for the services being performed, or certification byother qualified national authorities as appropriate to theservice, shall be considered as one means of documentingcompetency. The inspector or technician shall w

43、ork under thedirect supervision of personnel meeting the requirements of6.2.4 or 6.2.5.6.2.7 It is satisfactory for a person to fill one or more of thelevels of management, supervision, inspector, or technicianpositions in accordance with 6.2.2, 6.2.3, 6.2.4, and 6.2.5,provided the person qualifies

44、for the highest level worked. It isalso recognized that frequently some tests and inspections areconducted at small field or peripheral locations; it is not theintent of this specification that the supervisory personnel bedirectly present at such locations at all times. If the qualifiedperson in 6.2

45、.2 performs as a supervisor, they do not have tocomply with the certification requirements.6.3 Special Inspection Agency6.3.1 The following personnel requirements must be satis-fied by an agency that provides Special Inspection services:6.3.2 The Special Inspection services of the agency shall beund

46、er the direction of a registered design professional and afull-time employee of that agency. The person shall have atleast two years experience in Special Inspections. The organi-zation can consist of one or more separate facilities providingSpecial Inspection. A registered design professional can h

47、avemanagerial responsibility for one or more facilities within theorganization as defined by Section 5.6.3.3 The qualifications of the field supervisor shall bedetermined by the applicable building official. If no require-ments have been set forth, the field supervisor of SpecialInspection shall hav

48、e at least two years Special Inspectionexperience in the type of work being supervised. This personshall be certified in the areas he or she is supervising.6.3.4 The qualifications of the Special Inspector shall bedetermined by the applicable building official. If no require-ments have been set fort

49、h, the Special Inspector shall becertified by a third party. This certification exam shall include;a written examination that shall include; reading plans as aperformance element. The examination shall demonstrate thecandidates ability to correctly perform the required duties andevaluate the inspection results for specification and codecompliance.6.3.5 The registered design professional according to 6.3.2,in addition to the requirements of 6.3.4 shall document theexperience and job training of each Special Inspector beingsupervised. The Special Inspection agency shall mainta