ASTM E329-2011b 8125 Standard Specification for Agencies Engaged in Construction Inspection Testing or Special Inspection《施工检验 测试或专项检验从业机构执业标准规格》.pdf

《ASTM E329-2011b 8125 Standard Specification for Agencies Engaged in Construction Inspection Testing or Special Inspection《施工检验 测试或专项检验从业机构执业标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM E329-2011b 8125 Standard Specification for Agencies Engaged in Construction Inspection Testing or Special Inspection《施工检验 测试或专项检验从业机构执业标准规格》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E329 11bAn American National StandardStandard Specification forAgencies Engaged in Construction Inspection, Testing, orSpecial Inspection1This standard is issued under the fixed designation E329; the number immediately following the designation indicates the year oforiginal adoption or,

2、 in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.

3、1 This specification defines the minimum requirements forinspection agency personnel or testing agency laboratoryagencies engaged in:a. Construction inspection of construction and materialsused in construction,b. Special Inspection, andc. Testing of construction and materials used in construc-tion.1

4、.2 Criteria are provided for evaluating the competence ofan agency to properly perform designated tests, inspections, orSpecial Inspection services. This specification establishes es-sential characteristics pertaining to the organization, manage-ment, personnel, facilities, quality systems, responsi

5、bilities,duties, test and inspection methods, records, and reports of theagency. This specification may be supplemented by morespecific criteria and requirements if required.1.2.1 This specification specifically addresses factors rel-evant to an agencys ability to produce precise, accurate testdata

6、or determine the conformity of construction and materialsused in construction with regulations, codes, standards, orspecifications containing the requirements against which thetest or inspection will be performed, or both. Specific orgeneral requirements include:1.2.1.1 Technical competency of perso

7、nnel,1.2.1.2 Validity and appropriateness of test and inspectionmethods and procedures,1.2.1.3 Traceability of measurements and calibrations tonational standards,1.2.1.4 Suitability, calibration, and maintenance of testequipment,1.2.1.5 Sampling, handling, and transportation of test items,1.2.1.6 Qu

8、ality assurance of test and inspection data,1.2.1.7 Reporting of test and inspection data or findings, and1.2.1.8 Non Conformance Report (NCR) management andrecords.1.3 This specification can be used as a basis to assess anagency and is intended for use in accrediting agencies, publicor private, eng

9、aged in construction inspection. Special inspec-tion or testing of construction and materials used in construc-tion. These inspection services include but are not limited toreinforced concrete, precast concrete, structural steel erection,welding, bolting, soil and rock, foundations, masonry, sprayed

10、fire-resistive materials, fire stops, exterior insulation and finishsystem (EIFS), and Special Cases. Building officials can useSpecification E329 as a tool in the qualification and establish-ment of competency of construction inspection, Special inspec-tion, and testing agencies in the fields cover

11、ed by SpecificationE329.1.4 A certificate of accreditation, including the scope ofaccreditation, is required to comply with this specification.1.5 The users of an accredited agency must review theagencys scope of accreditation to ensure the agency has beenaccredited for its technical competence to p

12、erform the specifictests or inspections requested by the user.2. Referenced Documents2.1 ASTM Standards:2A880 Practice for Criteria for Use in Evaluation of TestingLaboratories and Organizations for Examination and In-spection of Steel, Stainless Steel, and Related Alloys3C1077 Practice forAgencies

13、Testing Concrete and ConcreteAggregates for Use in Construction and Criteria forTesting Agency EvaluationC1093 Practice for Accreditation of Testing Agencies forMasonryD3666 Specification for Minimum Requirements for Agen-cies Testing and Inspecting Road and Paving MaterialsD3740 Practice for Minimu

14、m Requirements for Agencies1This specification is under the jurisdiction of ASTM Committee E36 onAccreditation the data are used to evaluate ordetermine selected properties or characteristics of the activitiesor materials.4. Significance and Use4.1 The testing and inspection of construction and them

15、aterials in construction is an important element in obtainingquality construction in general compliance to the contractdocuments. A construction inspection, Special Inspection ortesting agency, or both, must be selected with care after acomprehensive evaluation of their competency to perform theserv

16、ices properly and in compliance with the applicablebuilding code.4.2 This specification provides basic minimum criteria foruse in evaluating the qualifications of technically orientedconstruction inspection, Special Inspection, or testing agency.The criteria may be supplemented by more specific crit

17、eria andrequirements for particular classes of testing or types ofinspection agencies. An individual user can also use it to judgethe competency of an agency.4.3 The intent of this specification is to provide a consensussystem standardized basis for requirements for a technicallyoriented constructio

18、n inspection, Special Inspection, or testingagency, with respect to the agencys capability to objectivelyand competently provide the specific services without preju-dice.4.4 Typically, assessing an agency involves the followingthree essential sequential phases:4.4.1 Submittal of basic information in

19、 accordance with thecriteria of this specification to the evaluator by an agencydesiring to be qualified to this specification,4.4.2 Assessing the agency-submitted information from theaccreditation body, and4.4.3 On-site assessment of the agency by the accreditationbody.5. Organization and Managemen

20、t5.1 The agency shall be legally identifiable. It shall beorganized and shall operate in such a way that its facilities meetthe requirements of this specification.5.1.1 Main facilities, sub-facilities, and permanent site fa-cilities shall maintain personnel, equipment, procedures, anddocumentation a

21、s required in this specification. The managerfor the main facility may also be responsible for a sub-facilityor permanent site facility (see 6.2.2 and 6.3.2). Main facilities,sub-facilities, and permanent site facilities shall be accreditedin accordance with 9.4.1 to perform the functions described

22、in3.1.2.1 or 3.1.2.2 or 3.1.2.4 of this specification.5.1.2 Temporary site facilities offering a defined scope ofservices for a specific project, which are demonstrably underthe main facilitys or sub-facilitys technical direction andE329 11b3quality program, do not require separate accreditation. Ag

23、en-cies that use temporary site facilities for their projects shalldescribe the operation of these facilities in their qualitymanual.5.1.3 An endorsement for the operation of temporary sitefacilities shall also be listed on the agencys accreditationcertificate.5.2 The agency shall:5.2.1 Have manager

24、ial personnel with the authority andresources needed to discharge their duties.5.2.2 Have arrangements to ensure that its personnel are freefrom any commercial, financial, and other pressures includingtrade organization rules that might adversely affect theirindependence of judgments and the integri

25、ty of their services.A Special Inspection agency or its personnel shall not bedirectly involved in the manufacture, supply, installation, use,or maintenance of the inspected items.5.2.3 Be organized in such a way that confidence in itsindependence of judgment and integrity is maintained at alltimes.

26、5.2.4 Specify and document the responsibility, authority,qualifications, and interrelation of all personnel who manage,perform, or verify services affecting the quality of inspectionsor tests, or both.5.2.5 Provide supervision by persons qualified to performthe inspections and tests and to implement

27、 relevant procedures.They shall be qualified to evaluate the objective of theinspections or tests and the results. The ratio of supervisory tonon-supervisory personnel shall be such as to ensure adequatesupervision.5.2.6 Have a technical manager (however named) who hasoverall responsibility for the

28、technical operations.5.2.7 Have a quality manager (however named) who has theresponsibility for the quality system and its implementation.The quality manager shall have direct access to the highestlevel of management at which decisions are made on agencypolicy or resources, and to the technical mana

29、ger. In someagencies, the quality manager may also be the technicalmanager or deputy technical manager.5.2.8 Nominate deputies in case of absence of the technicalor quality manager.5.2.9 Where relevant, have documented policy and proce-dures to ensure the protection of clients confidential informa-t

30、ion and proprietary rights.5.2.10 Where appropriate, as determined by the agencysquality manual, participate in interlaboratory comparisons andproficiency testing programs.6. Personnel6.1 General6.1.1 The agency shall have sufficient personnel having thenecessary education, training, technical knowl

31、edge, certifica-tion as appropriate, and experience for their assigned functions.6.1.2 The agency shall ensure that the training of itspersonnel is kept up-to-date.6.1.3 Records of relevant certification, qualifications, train-ing, skills, and experience of the technical personnel shall bemaintained

32、 by the agency.6.2 Construction Inspection and Testing Agency, or Both6.2.1 The following personnel requirements must be satis-fied by the agency when construction inspection or testingservices, or both, are being provided:6.2.2 The inspection and testing services of the agency, thatprovides the qua

33、lity control or quality assurance program, orboth, as related to construction or materials used in construc-tion, shall be under the direction of a person charged withengineering managerial responsibility. The person shall be alicensed/registered design professional and a full-time em-ployee of that

34、 agency. The person shall have at least five yearsexperience in testing and inspection of construction materials.The organization may consist of one or more separate facilitiesproviding inspection or testing services or both. A licensed/registered design professional may have engineering manage-rial

35、 responsibility for one or more facilities within the organi-zation.6.2.3 When a producers or manufacturers laboratory onlyserves as a quality control laboratory and does not producetests for acceptance, payment, or the official record, therequirement for a registered professional is waived. However

36、,the laboratory function of the organization shall be supervisedby a quality control manager. The quality control manager shallhave at least five years experience in testing of that particularconstruction material, and be a full time employee of theorganization. The quality control manager will have

37、 the au-thority to make changes in production to ensure that qualitymaterial is produced. He may serve as the quality controlmanager for several materials production facilities. The qualitycontrol manager shall have the certifications appropriate to thetesting of the materials supervised.6.2.4 A lab

38、oratory supervisor shall have at least three yearsexperience performing tests on relevant construction materials.This person shall be able to demonstrate either by oral orwritten examination, or both, their ability to perform the testsnormally required in the manner stipulated under ASTM orother gov

39、erning test procedures and shall be capable ofevaluating the test results in terms of specification compliance.Certification by qualified national, regional, or state authoritiesas appropriate to the services is required.6.2.5 A field supervisor shall have at least three yearsinspection experience i

40、n the type of services being supervised.This person shall be able to demonstrate, either by oral orwritten examination, or both, their ability to perform correctlythe required duties and shall be capable of evaluating theinspection or test results in terms of specification compliance.Certification b

41、y qualified national, regional, or state authoritiesas appropriate to the services is required.6.2.6 Inspector or TechnicianThis person shall have suf-ficient education and on-the-job training or trade schooltraining to properly perform the test or inspection to which theperson is assigned. This per

42、son must be able to demonstratecompetence for the test or inspection which is being conductedeither by oral or written examination, or both. Certification asappropriate for the services being performed, or certification byother qualified national authorities as appropriate to the work,shall be consi

43、dered as one means of documenting competency.E329 11b4The inspector or technician shall work under the directsupervision of personnel meeting the requirements of 6.2.4 or6.2.5.6.2.7 It is satisfactory for a person to fill one or more of thelevels of management, supervision, inspector, or technicianp

44、ositions in accordance with 6.2.2, 6.2.3, 6.2.4, and 6.2.5,provided the person qualifies for the highest level worked. It isalso recognized that frequently some tests and inspections areconducted at small field or peripheral locations; it is not theintent of this specification that the supervisory p

45、ersonnel bedirectly present at such locations at all times. If the qualifiedperson in 6.2.2 performs as a supervisor, they do not have tocomply with the certification requirements.6.3 Special Inspection Agency6.3.1 The following personnel requirements must be satis-fied by an agency that provides Sp

46、ecial Inspection services:6.3.2 The Special Inspection services of the agency shall beunder the direction of a licensed/registered design professionaland a full-time employee of that agency. The person shall haveat least two years experience in Special Inspections. Theorganization can consist of one

47、 or more separate facilitiesproviding Special Inspection. A licensed/registered designprofessional can have engineering managerial responsibilityfor one or more facilities within the organization as defined bySection 5.6.3.3 The qualifications of the field supervisor shall bedetermined by the applic

48、able building official. If no require-ments have been set forth, the following shall apply:6.3.3.1 Afield supervisor of Special Inspection shall have atleast two years Special Inspection experience in the type ofwork being supervised. This person shall be certified in theareas he or she is supervisi

49、ng.6.3.3.2 The qualifications of the Special Inspector shall bedetermined by the local building official. If no requirementshave been set forth, the following shall apply:6.3.3.3 ASpecial Inspector shall be certified by a third party.This certification exam shall include; a written examinationwhich shall include reading plans as a performance element.The examination shall demonstrate the candidates ability tocorrectly perform the required duties and evaluate the inspec-tion results for specification and code compliance.6.3.3.4 The licensed/registered design professional acco