ASTM E155-2015 red 4687 Standard Reference Radiographs for Inspection of Aluminum and Magnesium Castings《铝 镁铸件检验用标准参考射线照片》.pdf
《ASTM E155-2015 red 4687 Standard Reference Radiographs for Inspection of Aluminum and Magnesium Castings《铝 镁铸件检验用标准参考射线照片》.pdf》由会员分享,可在线阅读,更多相关《ASTM E155-2015 red 4687 Standard Reference Radiographs for Inspection of Aluminum and Magnesium Castings《铝 镁铸件检验用标准参考射线照片》.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: E155 14E155 15Standard Reference Radiographs forInspection of Aluminum and Magnesium Castings1This standard is issued under the fixed designation E155; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last r
2、evision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.These Reference Radiographs have been developed in cooperation with the Quality Control Committee and Aerospace Research andTesting Comm
3、ittee of the Aerospace Industries Association.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 These reference radiographs illustrate the types and degrees of discontinuities that may be found in aluminum-alloy andmagnesium-alloy castings. The casting
4、s illustrated are in thicknesses of 14 in. (6.35 mm) and 34 in. (19.1 mm). The referenceradiograph films are an adjunct to this document and must be purchased separately from ASTM International if needed.1.2 These film reference radiographs are not intended to illustrate the types and degrees of dis
5、continuities found inaluminum-alloy and magnesium-alloy castings when performing digital radiography. If performing digital radiography ofaluminum-alloy castings, refer to Digital Reference Image Standard E2422. If performing digital radiography of magnesium-alloycastings, refer to Digital Reference
6、 Image Standard E2869.1.3 This document may be used where no other applicable document exists, for other material thicknesses for which it has beenfound to be applicable and for which agreement has been reached between the purchaser and the manufacturer.1.4 From time to time, there may be minor chan
7、ges to the process for manufacturing of the reference radiograph adjunctmaterials. These changes could include changes in the films or processing chemicals used, changes in the dies or printing for thecardboard mats, etc.; however, in all cases, these changes are reviewed by the Illustration Monitor
8、ing Subcommittee and allreference radiographs are reviewed against a fixed prototype image to ensure that there are no changes to the acceptance levelrepresented by the reference radiographs. Therefore, the adjunct reference radiographs remain valid for use with this standardregardless of the date o
9、f production or the revision level of the text standard.1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information only and are not considered standard.1.6 This standard does
10、not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatorylimitations prior to use.NOTE 1Vol I: The set of reference radiog
11、raphs consists of 13 plates covering discontinuities in aluminum-alloy castings and 10 plates coveringdiscontinuities in magnesium-alloy castings. Each plate is held in an 812 by 11-in. (216 by 279-mm) cardboard frame and each plate illustrates eightgrades of severity for the discontinuity in approx
12、imately a 2 by 2-in. (51 by 51-mm) area. The cardboard frames are contained in a 1012 by 1112-in. (267by 292-mm) ring binder. The reference radiographs are not impacted by this revision. There have been no revisions to the adjunct reference radiographssince original issue. The adjunct reference radi
13、ographs of any issue remain valid and may be used to this standard.Vol. II: The set of reference radiographs consists of four plates covering discontinuities in magnesium-alloy castings only. Each plate is held in an 812by 11-in. (216 by 279-mm) cardboard frame and illustrates eight grades of severi
14、ty for the discontinuity (with the exception of discrete discontinuities,where only one example of each discontinuity is given).NOTE 2Reference radiographs applicable to aluminum and magnesium die castings up to 1 in. (25 mm) in thickness are contained in ReferenceRadiographs E505.2. Referenced Docu
15、ments2.1 ASTM Standards:2E94 Guide for Radiographic Examination1 These reference radiographs are under the jurisdiction of ASTM Committee E07 on Nondestructive Testing and are the direct responsibility of Subcommittee E07.02on Reference Radiological Images.Current edition approved Oct. 1, 2014Sept.
16、1, 2015. Published October 2014September 2015. Originally approved in 1960. Last previous edition approved in 20102014as E155 - 10.E155 - 14. DOI: 10.1520/E0155-14.10.1520/E0155-15.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org
17、. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit m
18、ay not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Har
19、bor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1E505 Reference Radiographs for Inspection of Aluminum and Magnesium Die CastingsE1316 Terminology for Nondestructive ExaminationsE2422 Digital Reference Images for Inspection of Aluminum CastingsE2869 Digital Reference Images fo
20、r Magnesium Castings2.2 ASTM Adjuncts:Reference Radiographs for Inspection of Aluminum and Magnesium Castings:Volume I, Aluminum and Magnesium Castings3Volume II, Magnesium Castings43. Terminology3.1 DefinitionsDefinitions of terms used in this standard may be found in Terminology E1316.3.2 Definiti
21、ons of Terms Specific to This Standard:3.2.1 The terms relating to discontinuities used in these reference radiographs are described based upon radiographicappearance.3.2.2 foreign materialsappear as isolated, irregular, or elongated variations of film density, not corresponding to variations inthic
22、kness of material, nor to cavities. They may be due to the presence of sand, slag, oxide or dross, or metal of different density.3.2.3 gas holesappear as round or elongated, smooth-edged dark spots, occurring individually, in clusters, or distributedthroughout the casting.3.2.4 gas porosityrepresent
23、ed by round or elongated dark spots corresponding to minute voids usually distributed through theentire casting.3.2.5 microshrinkage (feathery type)microshrinkage having an elongated appearance resembling feather-like streaks.3.2.6 microshrinkage (sponge type)microshrinkage having a spongelike appea
24、rance, and more massive and equiaxed than thefeathery type.3.2.7 reacted sand inclusionsappear on radiograph as “spotty segregation,” that is, sharply defined round light areas, about1 mm in diameter, and often with the rim lighter than the center. They are entrapped sand particles that underwent re
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTME1552015RED4687STANDARDREFERENCERADIOGRAPHSFORINSPECTIONOFALUMINUMANDMAGNESIUMCASTINGS 铸件 检验 标准 参考

链接地址:http://www.mydoc123.com/p-526987.html