ASTM D7842 D7842M-2012 3750 Standard Test Method for Holding Strength of Tack and Prong Fastener Attached Buttons《粘性和爪紧紧固件连接按钮夹持强度的标准试验方法》.pdf

《ASTM D7842 D7842M-2012 3750 Standard Test Method for Holding Strength of Tack and Prong Fastener Attached Buttons《粘性和爪紧紧固件连接按钮夹持强度的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM D7842 D7842M-2012 3750 Standard Test Method for Holding Strength of Tack and Prong Fastener Attached Buttons《粘性和爪紧紧固件连接按钮夹持强度的标准试验方法》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D7842/D7842M 12Standard Test Method forHolding Strength of Tack and Prong Fastener AttachedButtons1This standard is issued under the fixed designation D7842/D7842M; the number immediately following the designation indicates theyear of original adoption or, in the case of revision, the y

2、ear of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of the holdingstrength of a tack and prong fastener attached button u

3、sing atensile testing machine.1.2 This test method is applicable to attached buttons ingarments or to be attached to fabrics intended for use in apparel(see Annex A1).1.3 UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard. Thevalues stated in each

4、 system may not be exact equivalents;therefore, each system shall be used independently of the other.Combining values from the two systems may result in non-conformance with the standard.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is t

5、heresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D76 Specification for Tensile Testing Machines for TextilesD123 Terminology Relating

6、to TextilesD1776 Practice for Conditioning and Testing Textiles2.2 Federal Document:316 CFR Parts 1500.48-1500.53 and 1501.4 Engineering TestManual for Childrens Toys3. Terminology3.1 Definitions:3.1.1 force, na physical influence exerted by one body onanother which produces acceleration of bodies t

7、hat are free tomove and deformation of bodies that are not free to move.3.1.2 holding strength, nin buttons, the force required toseparate the button from its attached mating part or separatefrom the fabric it is attached to, whichever shall fail first.3.1.3 tack attached button, nany button that is

8、 attached bya single post product (most commonly used to attach a nonmetal colleted button). (See Fig. 1.)3.1.4 prong fastener attached button, nany button that isattached by a product with 2 or more prongs (most commonlyused to attach a metal colleted button). (See Fig. 2.)3.1.5 For definitions of

9、other textile terms used in thisstandard, refer to Terminology D123.4. Summary of Test Method4.1 A specimen, consisting of a button and tack or prongfastener attached to a fabric, is mounted in a special test fixtureon a tensile testing machine. A force is applied perpendicularlyuntil the button sep

10、arates from the tack or prong fastener, or thefabric is torn. The peak force at separation is reported as theholding strength. If the fabric tears, the peak force at fabricfailure is recorded and the data is reported and considered as adifferent category to be reported separately from the holdingstr

11、ength of the fasteners.5. Significance and Use5.1 This test method may be used for acceptance testing ofcommercial shipments of garments with attached buttons.5.2 This test method may be used to determine the compat-ibility of tack attached buttons or prong fastener attachedbuttons to fabrics used i

12、n apparel. In which case, the buttonsare attached to the fabric in the manner in which they will beused and the combined units tested.6. Apparatus6.1 Tensile Testing Machine, CRE type, meeting Specifica-tion D76. (See Fig. 3.)6.1.1 Upper Test Fixture, Fig. 4, designed as not to malformthe button spe

13、cimen with interchangeable bottom plates to testa multitude of sizes of buttons.1This test method is under the jurisdiction of ASTM Committee D13 on Textilesand is the direct responsibility of Subcommittee D13.54 on Subassemblies.Current edition approved Dec. 1, 2012. Published December 2012. DOI:10

14、.1520/D7842-12.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from U.S. Government Printing Offic

15、e Superintendent of Documents,732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401, http:/www.access.gpo.gov.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States17. Sampling, Test Specimens, and Test Units7.1 Lot Sample:7.1.1 For a

16、cceptance testing, randomly select the number ofshipping cartons or other containers of garments as directed inan applicable material specification, contract or other agree-ment between the purchaser and the supplier. Consider thecartons or containers to be the primary sampling units.7.2 Laboratory

17、Sample:7.2.1 For acceptance testing, take necessary number ofgarments to obtain ten attachments. Button fly attachmentsshould be tested separately from waste band attached buttons.7.3 Test Specimens:7.3.1 Test ten specimens from each garment. A test speci-men consists of the button, fabric, and prod

18、uct (tack or prongfastener) used to attach button to fabric. The locations of thespecimens must allow for secure clamping in the fixtures. Extratests may need to be performed if fabric fails before reachingeither the force specification agreed upon by the purchaser andsupplier or 69 N 15.5 lb. If th

19、e fabric fails before reaching 69N, it is recommended to try a thicker application (more layersof fabric) if possible, until ten tested specimens have no fabricfailures.8. Preparation of Apparatus8.1 Preparation:8.1.1 Set up and verify the tensile testing machine accordingto the manufacturers instru

20、ctions and 8.1.2-8.1.4.8.1.2 Attach the upper fixture to the testing machine andcheck the alignment.8.1.3 Select a force range for separation to occur between 10and 90 % of full scale force.8.1.4 Set the loading rate for 300 6 10 mm/min 12.0 6 0.5in./min.9. Calibration and Standardization9.1 Testing

21、 equipment should be calibrated on a regularbasis as recommended by manufacturers instructions.10. Conditioning10.1 Condition the specimens by bringing them from thedry side to approximate moisture equilibrium for testing in thestandard atmosphere for testing textiles as directed in PracticeD1776.11

22、. Procedure11.1 The attached button is placed in the test fixture. Thetest fixture is clamped to the top jaws of the Tensile Testingmachine and the fabric is clamped to the bottom jaws. (See Fig.5.)11.2 Initiate the test by applying force to the machine untilthe button disengages from the fastener o

23、r the fabric tears.11.3 Record the force to disengage the button from thefastener as the holding force to the nearest 0.1 N 0.5 lbf.12. Calculation or Interpretation of Results12.1 If the fabric tears before the fastener and buttondisengage, record the specimen as failing. The value of thefabric fai

24、lure specimen is recorded separate from the recordingof the values of the fastener holding strength.13. Report13.1 State that the tests were made as directed in TestMethod D7842. Describe the material or product beingsampled and the method of sampling used. Describe thematerial and end product.13.2

25、Report the following information:13.2.1 Type of testing machine and load range used.13.2.2 Individual and average results.13.2.3 Note of any fabric or tack/fastener failure besideresults with FF for fabric and T/F for tack/fastener. Disregardfabric failures. Use photos if needed to show the differen

26、cebetween fabric failure and tack/fastener failure.13.2.4 Report the units of force in newtons (N) or poundsforce lbf.13.2.5 Report thickness of fabric using compressed founda-tion thickness.14. Precision and Bias14.1 The value for holding strength of a button, either tackattached or prong attached,

27、 in garments can only be defined bya test method. Within this limitation, Test Method D7842 hasno known biases.15. Keywords15.1 button; prong fastener; strength; tackFIG. 1 Tack AttachedFIG. 2 Prong Fastener AttachedD7842/D7842M 122FIG. 3 Tensile Test Machine and Clamped Test SpecimenFIG. 4 Upper Te

28、st FixtureD7842/D7842M 123ANNEX(Mandatory Information)A1. SELECTION OF BUTTON (TACK OR PRONG ATTACHED) FOR USE IN GARMENTSA1.1 Button (Tack or Prong attached) and FabricA1.1.1 ButtonSize appropriate to the type of fabric to beused in the garment. Some fabrics may require Tack attachmentand some may

29、require Prong attachment.A1.1.2 FabricFor which the particular button is beingassessed for suitability.A1.1.3 Interliner FabricAs needed in garment construc-tion.A1.2 Number of SpecimensA1.2.1 Test until ten buttons have passed the specifiedrequirement by the purchaser and supplier or 69 N 15.5 lb.A

30、1.3 Preparation of Setup SpecimensA1.3.1 Use fabric supplied by the purchaser or supplier withthe same thickness as the actual garment that the button isbeing applied. If an interliner is to be in the area of the garmentin which the button is to be used, be sure to include betweenthe fabrics. Please

31、 note that some garments may be processedbefore or after the attachment of the button. Chemicals used toprocess the garment could affect the results of this test.A1.3.2 Attach the buttons to the manufacturers instruc-tions. Additional equipment may be needed to attach thebuttons or the supplier or p

32、urchaser may attach the buttonsusing their equipment.A1.4 TestingA1.4.1 Test the specimens as directed in Section 11.A1.5 ReportA1.5.1 Report the applicable information as stated in Sec-tion 13.FIG. 5 Specimen Clamping ConfigurationD7842/D7842M 124ASTM International takes no position respecting the

33、validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is

34、subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Head

35、quarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This sta

36、ndard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D7842/D7842M 125