ASTM D7128-2018 3125 Standard Guide for Using the Seismic-Reflection Method for Shallow Subsurface Investigation.pdf
《ASTM D7128-2018 3125 Standard Guide for Using the Seismic-Reflection Method for Shallow Subsurface Investigation.pdf》由会员分享,可在线阅读,更多相关《ASTM D7128-2018 3125 Standard Guide for Using the Seismic-Reflection Method for Shallow Subsurface Investigation.pdf(26页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D7128 18Standard Guide forUsing the Seismic-Reflection Method for ShallowSubsurface Investigation1This standard is issued under the fixed designation D7128; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of l
2、ast revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 Purpose and Application:1.1.1 This guide summarizes the technique, equipment, fieldprocedures, data processing, and int
3、erpretation methods for theassessment of shallow subsurface conditions using the seismic-reflection method.1.1.2 Seismic reflection measurements as described in thisguide are applicable in mapping shallow subsurface conditionsfor various uses including geologic (1), geotechnical, hydro-geologic (2),
4、 and environmental (3).2The seismic-reflectionmethod is used to map, detect, and delineate geologic condi-tions including the bedrock surface, confining layers(aquitards), faults, lithologic stratigraphy, voids, water table,fracture systems, and layer geometry (folds). The primaryapplication of the
5、seismic-reflection method is the mapping oflateral continuity of lithologic units and, in general, detectionof change in acoustic properties in the subsurface.1.1.3 This guide will focus on the seismic-reflection methodas it is applied to the near surface. Near-surface seismicreflection applications
6、 are based on the same principles asthose used for deeper seismic reflection surveying, but ac-cepted practices can differ in several respects. Near-surfaceseismic-reflection data are generally high-resolution (dominantfrequency above 80 Hz) and image depths from around6mtoas much as several hundred
7、 meters. Investigations shallowerthan 6 m have occasionally been undertaken, but these shouldbe considered experimental.1.2 Limitations:1.2.1 This guide provides an overview of the shallowseismic-reflection method, but it does not address the details ofseismic theory, field procedures, data processi
8、ng, or interpre-tation of the data. Numerous references are included for thatpurpose and are considered an essential part of this guide. It isrecommended that the user of the seismic-reflection method befamiliar with the relevant material in this guide, the referencescited in the text, and Guides D4
9、20, D653, D2845, D4428/D4428M, Practice D5088, Guides D5608, D5730, D5753,D6235, and D6429.1.2.2 This guide is limited to two-dimensional (2-D) shal-low seismic-reflection measurements made on land. Theseismic-reflection method can be adapted for a wide variety ofspecial uses: on land, within a bore
10、hole, on water, and in threedimensions (3-D). However, a discussion of these specializedadaptations of reflection measurements is not included in thisguide.1.2.3 This guide provides information to help understandthe concepts and application of the seismic-reflection methodto a wide range of geotechn
11、ical, engineering, and groundwaterproblems.1.2.4 The approaches suggested in this guide for theseismic-reflection method are commonly used, widelyaccepted, and proven; however, other approaches or modifica-tions to the seismic-reflection method that are technicallysound may be equally suited.1.2.5 T
12、echnical limitations of the seismic-reflection methodare discussed in 5.4.1.2.6 This guide discusses both compressional (P) and shear(S) wave reflection methods. Where applicable, the distinctionsbetween the two methods will be pointed out in this guide.1.3 This guide offers an organized collection
13、of informationor a series of options and does not recommend a specificcourse of action. This document cannot replace education orexperience and should be used in conjunction with professionaljudgment. Not all aspects of this guide may be applicable in allcircumstances. This guide is not intended to
14、represent orreplace the standard of care by which the adequacy of a givenprofessional service must be judged, nor should this documentbe applied without consideration for a projects many uniqueaspects. The word “Standard” in the title of this guide meansonly that the document has been approved throu
15、gh the ASTMconsensus process.1.4 The values stated in SI units are regarded as standard.The values given in parentheses are inch-pound units, whichare provided for information only and are not consideredstandard.1This guide is under the jurisdiction ofASTM Committee D18 on Soil and Rockand is the di
16、rect responsibility of Subcommittee D18.01 on Surface and SubsurfaceCharacterization.Current edition approved July 15, 2018. Published August 2018. Originallyapproved in 2005. Last previous edition approved in 2010 as D712805(2010).DOI: 10.1520/D7128-18.2The boldface numbers in parentheses refer to
17、the list of references at the end ofthis standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the
18、Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.11.5 Precautions:1.5.1 It is the responsibility of the user of this guide tofollow any precautions within the equipment
19、manufacturersrecommendations, establish appropriate health and safetypractices, and consider the safety and regulatory implicationswhen explosives or any high-energy (mechanical or chemical)sources are used.1.5.2 If the method is applied at sites with hazardousmaterials, operations, or equipment, it
20、 is the responsibility ofthe user of this guide to establish appropriate safety and healthpractices and determine the applicability of any regulationsprior to use.1.5.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of th
21、e user of this standard to establish appro-priate safety, health, and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization establishe
22、d in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:3D420 Guide for Site Characterization for Engineering De-sign and Con
23、struction PurposesD653 Terminology Relating to Soil, Rock, and ContainedFluidsD2845 Test Method for Laboratory Determination of PulseVelocities and Ultrasonic Elastic Constants of Rock(Withdrawn 2017)4D3740 Practice for Minimum Requirements for AgenciesEngaged in Testing and/or Inspection of Soil an
24、d Rock asUsed in Engineering Design and ConstructionD4428/D4428M Test Methods for Crosshole Seismic Test-ingD5088 Practice for Decontamination of Field EquipmentUsed at Waste SitesD5608 Practices for Decontamination of Sampling and NonSample Contacting Equipment Used at Low Level Radio-active Waste
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD712820183125STANDARDGUIDEFORUSINGTHESEISMICREFLECTIONMETHODFORSHALLOWSUBSURFACEINVESTIGATIONPDF

链接地址:http://www.mydoc123.com/p-524577.html