ASTM D7121-2005(2012) 9767 Standard Test Method for Rubber PropertyResilience Using Schob Type Rebound Pendulum《用Schob型回弹摆锤测定橡胶回弹特性的标准试验方法》.pdf

《ASTM D7121-2005(2012) 9767 Standard Test Method for Rubber PropertyResilience Using Schob Type Rebound Pendulum《用Schob型回弹摆锤测定橡胶回弹特性的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM D7121-2005(2012) 9767 Standard Test Method for Rubber PropertyResilience Using Schob Type Rebound Pendulum《用Schob型回弹摆锤测定橡胶回弹特性的标准试验方法》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D7121 05 (Reapproved 2012)Standard Test Method forRubber PropertyResilience Using Schob Type ReboundPendulum1This standard is issued under the fixed designation D7121; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, th

2、e year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers a means of determining theresilience of rubber, within a range of impact strain and

3、strainrate, by means of the impacting and measuring apparatusconforming to the requirements described in this test method.1.2 This test method is applicable to thermoset rubbers andthermoplastic elastomers, the hardness of which, at the speci-fied test temperatures, lies between 30 and 85 IRHD (see

4、TestMethod D1415) or A/30 and A/85 (see Test Method D2240). Itmay also be applicable to some polyester, polyether foam, andplastic foam materials.1.3 All materials, instruments, or equipment used for thedetermination of mass, force, or dimension shall have trace-ability to the National Institute for

5、 Standards and Technology,or other internationally recognized organization parallel innature.1.4 The values stated in SI units are to be regarded asstandard. The values given in parentheses are for informationonly.1.5 This standard does not purport to address all of thesafety concerns, if any, assoc

6、iated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D832 Practice for Rubber Conditioning For Low Tempera-ture

7、 TestingD1349 Practice for RubberStandard Temperatures forTestingD1415 Test Method for Rubber PropertyInternationalHardnessD2240 Test Method for Rubber PropertyDurometerHardnessD3182 Practice for RubberMaterials, Equipment, andProcedures for Mixing Standard Compounds and Prepar-ing Standard Vulcaniz

8、ed SheetsD3183 Practice for RubberPreparation of Pieces for TestPurposes from ProductsD4483 Practice for Evaluating Precision for Test MethodStandards in the Rubber and Carbon Black ManufacturingIndustries3. Summary of Test Method3.1 This test method describes the determination of resil-ience, expre

9、ssed as percentage resilience or rebound resilience,by a Schob Type pendulum rebound device as a ratio betweenthe returned and applied energy when a spherically terminatedmass impacts a test specimen under the conditions specified inthis test method.3.2 Resilience of the materials described is infin

10、itely vari-able. It varies with temperature, strain rate (specifically relatedto the velocity of the indentor), and strain energy (specificallyrelated to the mass of the indentor, coupled with velocity).3.3 The variable factors, described and defined in this testmethod, will have effects on the outc

11、omes of test results.Repetitive tests, under the defined conditions, on comparablematerials, will provide meaningful, repeatable, and reproduc-ible data.4. Significance and Use4.1 The Schob Type rebound pendulum is designed tomeasure the percentage resilience of a rubber compound as anindication of

12、hysteretic energy loss that can also be defined bythe relationship between storage modulus and loss modulus.The percent rebound measured is inversely proportional to thehysteretic loss.1This test method is under the jurisdiction of ASTM Committee D11 on Rubberand is the direct responsibility of Subc

13、ommittee D11.14 on Time and Temperature-Dependent Physical Properties.Current edition approved May 1, 2012. Published July 2012. Originally approvedin 2005. Last previous edition approved in 2005 as D7121 05. DOI: 10.1520/D7121-05R12.2For referenced ASTM standards, visit the ASTM website, www.astm.o

14、rg, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4.1.1 Percen

15、tage resilience or rebound resilience are com-monly used in quality control testing of polymers and com-pounding chemicals.4.1.2 Rebound resilience is determined by a freely fallingpendulum hammer that is dropped from a given height thatimpacts a test specimen and imparts to it a certain amount ofen

16、ergy. A portion of that energy is returned by the specimen tothe pendulum and may be measured by the extent to which thependulum rebounds, whereby the restoring force is determinedby gravity.4.1.2.1 Since the energy of the pendulum is proportional tothe vertical component of the displacement of the

17、pendulum, itmay be expressed as 1 cos (of the angle of displacement) andpercentage rebound resilience. RB, commonly called percent-age rebound, is determined from the equation:RB 51 2 cos angle of rebound!1 2 cos original angle!3 100 (1)4.1.2.2 The rebound resilience may be calculated as:R 5hH(2)whe

18、re:h = apex height of the rebound, andH = initial height.4.1.2.3 The rebound resilience may also be determined bythe measurement of the angle of rebound a. From the reboundangle a, the rebound resilience in percent is obtained accordingto the following formula:R 5 1 2 cos a! 3 100 (3)5. Apparatus5.1

19、 Rebound resilience shall be measured by means of aSchob Type pendulum rebound device (see Fig. 1), which maybe described as a pendulum-like, one-degree-of-freedom, me-chanical oscillatory rebound device.5.1.1 The device shall consist of a pendulum rod terminat-ing in a hammer and hammer peen (spher

20、ical indentor)supported by a frame (see Fig. 2) so as to oscillate linearly orcircularly under the action of a restoring force, which may bedue to gravity or the elastic reactions of a torsion wire orsprings. It shall also incorporate a specimen holder and adevice by which to determine the outcome o

21、f the resiliencetest, either an analog scale with a pointer, or an equivalentdigital electronic display.5.2 The scale or display shall read either, or both, the angleof rebound and the horizontal rebound distance. The scale ordisplay may be graduated uniformly or be calibrated in units ofresilience.

22、5.3 The test specimen shall be securely held during me-chanical conditioning and rebound measurement.5.3.1 The surface against which the back of the test speci-men is applied shall be metallic, flat, and smoothly finished,vertical and perpendicular to the impact velocity direction.5.3.2 This flat fa

23、ce is a part of an anvil which shall, if free,have a mass of least 200 times the impacting mass.5.3.3 Any type of suitable holding device may be usedprovided that it gives rebound resilience values that deviate notmore than 0.2 (absolute rebound resilience) from those ob-tained with test specimens b

24、onded to a rigid back plate.5.3.3.1 Examples of suitable holding devices include suc-tion (by vacuum), mechanical clamping devices, and combi-nations of the two.5.3.3.2 No lateral restraint shall be applied to the testspecimen in order to allow it to bulge freely when impacted.5.4 If measurements ar

25、e to be carried out at a series oftemperatures different from the ambient temperature, the pen-dulum instrument shall be operated in accordance with Prac-tices D832 and D1349.5.4.1 The apparatus shall be checked for correct operation inthe range of temperatures used.5.4.2 Samples shall be conditione

26、d at temperature andremoved as quickly as possible to the tester (see 8.1.3).6. Test Specimens6.1 Test specimens shall be prepared in accordance withPractices D3182 and D3183 either by molding or by cutting.They shall be free of fabric or any other reinforcing materials.6.2 Test specimen size shall

27、be as described by the instru-ment manufacturer or as agreed upon by supplier and customer.6.3 The test specimens shall have flat, smooth, and parallelsurfaces, finished, if necessary, by buffing. If the impactedsurface is cohesive, the effect shall be minimized by dustingthe surface with talc or an

28、 equivalent material.6.3.1 Specimens may be prepared by plying samples cutfrom a standard test slab (see Practices D3182 and D3183).These samples shall be plied, without cementing, to thethickness required. Such plies shall be smooth, flat, and ofuniform thickness. The results obtained with these sp

29、ecimensso prepared will not necessarily be identical with thoseobtained using a solid specimen of the same material and stateof cure.6.3.1.1 Plying of no more than three test specimens of thesame material may be used to obtain a greater thickness. It isnecessary that the surfaces of the test specime

30、ns be verysmooth, and lateral suction may help in ensuring their contact.6.3.1.2 Plying of test specimens introduces additional un-certainties, and shall be used only for comparative measure-ments.6.4 The test shall be performed no earlier than 16 h and nolater than 28 days beyond the time of vulcan

31、ization.6.5 The time between vulcanization and testing shall notexceed 120 days for finished articles.6.5.1 Alternatively, the time between vulcanization andtesting may be agreed upon between laboratories or customerand supplier.6.6 Samples and test specimens shall be protected from lightas complete

32、ly as possible during the interval between vulcani-zation and testing.6.7 If the test specimen is buffed, the interval betweenbuffing and testing shall not exceed 72 h.7. Tester Verification7.1 Since there are no absolute standards available for thistester, the instruments performance should be veri

33、fied on aregular basis:D7121 05 (2012)27.1.1 Follow manufacturers recommendations for physicalverification of the instrument.7.1.2 Obtain or produce one or two standard samples,preferably one with high (90 %) resilience and one with low(20 to 30 %) resilience. Test these samples normally to verifyin

34、strument performance.8. Test Conditions8.1 The standard laboratory temperature of 23 6 2C (73.46 3.6F) is the preferred temperature of the test.8.1.1 Tests may also be carried out at other temperatures asagreed upon between laboratories or customer and supplier.8.1.2 The temperature tolerance shall

35、not exceed 61C.8.1.3 When tests are conducted at temperatures other thanthat in 8.1, the sample should be conditioned for at least 30 minor until uniformity of temperature is reached, then removedquickly to the tester to reduce the temperature change beforetesting.9. Procedure9.1 After conditioning

36、and mounting the test specimen inthe holding device, carry out mechanical conditioning bysubjecting the test specimen to no fewer than three and not1 Bubble Level2 Release3 Pendulum Angle Adjusting Screw4 Pendulum Mass5 Hammer (indentor)6 Anvil7 Leveling Feet8 Anvil Positioning Screw9 Power Switch10

37、 Display11 Observation Window12 Specimen HolderFIG. 1 Typical Schob Type Pendulum Rebound ApparatusD7121 05 (2012)3more than seven successive impacts, so as to reach a practicallyconstant rebound amplitude.9.2 Immediately after the impacts for mechanical condition-ing, apply three more impacts at th

38、e same velocity to testspecimen and note the three rebound readings.9.3 Convert these three readings, if necessary (see Section4), to resilience values, expressed as a percentage. Theirmedian shall be taken as the rebound resilience of the testspecimen.9.4 Calculate the average of the values for the

39、 two (or more)test specimens.10. Test Report10.1 The test report shall include:10.2 Test Details:10.2.1 Full description of the sample and its origin, includ-ing vulcanization date,10.2.2 Dimensions of the test specimen,10.2.3 Compound details and curing conditions, if known,10.2.4 Preparation of te

40、st specimens, for example whethermolded or cut and if the specimens were plied,10.2.5 Any relevant facts about the pretest history of testspecimens,10.2.6 Apparatus employed, and10.2.7 Methodology used.10.3 Test Results:10.3.1 Number of test specimens tested, and10.3.2 Calculated mean value or rebou

41、nd resilience, inpercent, for the test specimens.11. Precision and Bias11.1 Precision and bias have not been determined. Aninterlaboratory test program (ITP) will be conducted within theallotted time.11.2 The standard definitions relative to precision and bias,as defined in Practice D4483, have been

42、 included for reference.12. Keywords12.1 impact; oscillatory device; pendulum rebound; re-bound; resilience; rubberASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly ad

43、vised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, eithe

44、r reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend.

45、If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Indiv

46、idual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).FIG. 2 Schematic Detail of the Schob DeviceD7121 05 (2012)4