ASTM D6881 D6881M-2003(2008)e1 809 Standard Classification for Standard Plastics Industry Bulk Box Pallet Unit Size Classified By Bulk Density《按体积密度分类标准塑料工业容积箱／托盘单元尺寸分类》.pdf

《ASTM D6881 D6881M-2003(2008)e1 809 Standard Classification for Standard Plastics Industry Bulk Box Pallet Unit Size Classified By Bulk Density《按体积密度分类标准塑料工业容积箱／托盘单元尺寸分类》.pdf》由会员分享，可在线阅读，更多相关《ASTM D6881 D6881M-2003(2008)e1 809 Standard Classification for Standard Plastics Industry Bulk Box Pallet Unit Size Classified By Bulk Density《按体积密度分类标准塑料工业容积箱／托盘单元尺寸分类》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 6881/D 6881M 03 (Reapproved 2008)1Standard Classification forStandard Plastics Industry Bulk Box/Pallet Unit SizeClassified By Bulk Density1This standard is issued under the fixed designation D 6881/D 6881M; the number immediately following the designation indicates theyear of origina

2、l adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTEThe designation of this classification was editorially corrected to be D

3、6881/D 6881M in August 2008.INTRODUCTIONAn ad-hoc survey in 2000 showed about 40 different box sizes in use by the plastic resin industry;the purpose for this classification is to quantify a box/pallet unit size acceptable for this industry withinthe limits of the scope.1. Scope1.1 This classificati

4、on covers containers used to hold plasticresins with bulk density (Test Methods D 1895)of27to39lb/ft3(0.432 to 0.625 g/cm3).1.2 This classification does not apply to any plastic resinswith bulk density below 27 lb/ft3(0.432 g/cm3) or above39lb/ft3(0.625 g/cm3).1.3 This classification does not apply

5、to bulk boxes contain-ing hazardous materials.1.4 This classification does not address box/pallet unitiza-tion requirements.1.5 This classification does not address requirements ofplastic bag liners normally placed inside the corrugated bulkbox before filling with plastic resin.1.6 This classificati

6、on does not address tamping, shaking, orother compression methods of the resin filled bulk box tocondense entrained air and increase headspace in the bulk box.1.7 This classification does not address blocking and brac-ing or other shipping requirements normally associated withbulk box unit deliverie

7、s.1.8 This classification does not address filled bulk box/palletunit stack height.1.9 This classification does not address international ship-ping regulations of bulk box/pallet units.1.10 This classification does not address pallet openingsizes for pallet trucks.1.11 The values stated in either SI

8、 units or inch-pound unitsare to be regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.1.12 This standard do

9、es not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory requirements prior to use.1.13 This classification offers an

10、 organized collection ofinformation or a series of options and does not recommend aspecific course of action. This document cannot replace edu-cation or experience and should be used in conjunction withprofessional judgement. Not all aspects of this classificationmay be applicable in all circumstanc

11、es. This ASTM standard isnot intended to represent or replace the standard of care bywhich the adequacy of a given professional service must bejudged, nor should this document be applied without consid-eration of a projects many unique aspects. The word “stan-dard” in the title of this document mean

12、s only that thedocument has been approved through the ASTM consensusprocess.2. Referenced Documents2.1 ASTM Standards:2D 1895 Test Methods for Apparent Density, Bulk Factor,and Pourability of Plastic Materials3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 bulk box, plastic re

13、sin, na container used to enclose,protect, hold, and transport plastic resin, with net weights of1This classification is under the jurisdiction of ASTM Committee D10 onPackaging and is the direct responsibility of Subcommittee D10.12 on ShippingContainers, Crates, Pallets, Skids and Related Structur

14、es.Current edition approved Aug. 1, 2008. Published August 2008. Originallyapproved in 2003. Last previous edition approved in 2003 as D6881 03.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards v

15、olume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.about 1000 to 1600 lb (453.6 to 725.7 kg); it will havesemi-rigid sidewalls that resist bulging of the

16、 sidewall whenloaded, retain the approximate size of the empty assembledbox, and prevent collapse of the container during removal ofthe product.3.1.1.1 DiscussionNormally, the box is placed on a palletor skid, filled, and stacked one pallet load on the other for astack height selected by the user.3.

17、1.2 freeboard, namount of bulk box set back from palletedge on all sides to offset the bulge of the container when filledwith resin (typically 7 to 8 % of pallet dimension).3.1.3 pinwheeling, vwhen lengthwise loading vans orcontainers, the turning of a bulk box 90 and loading width-wise.3.1.4 plasti

18、c resin, norganic compounds produced bypolymerization that are flowable forms of filled or unfilledpowder, flake, chips, pellets, or granules originating fromeither virgin, compounded, regrind, or reclaim polymer.4. Significance and Use4.1 This standard classification will be used to:4.1.1 Standardi

19、ze the package size increasing availability,versatility, and acceptability of bulk box/pallet units.4.1.2 Lower transport package manufacturing costs.4.1.3 Lower cost/lb of packaged resin because of higher netweight/package.4.1.4 Reduce environmental impact of pallets and bulkboxes by reducing waste

20、.4.1.5 Support reuse of bulk boxes and pallets throughout thesupply chain.4.1.6 Optimize lifecycle package cost.4.1.7 Improve both inbound and outbound freight cost incomparison to non-optimal packaging.4.1.8 Lower inventory/storage cost of raw materials (needless on hand).4.1.9 Reduce warehouse spa

21、ce for resin storage.4.1.10 Reduce forklift trips (carrying higher weight).4.1.11 Promote multi-industry usage of common footprintboxes and pallets (examples are the automotive and chemicaldrum industry).4.1.12 Guide the first-time resin packager as to a successfulbulk box/pallet unit now in use in

22、the resin industry.4.1.13 Optimize net product weight in truckload trailer vansand oversea containers.4.2 This standard classification will be used by:4.2.1 Resin producers/converters/compounders/customersto compare with their current practice.4.2.2 Bulk box manufacturers to recommend a provencost-e

23、ffective package for plastic resins in the targeted bulkdensity range.4.2.3 Pallet manufacturers as a common bulk box footprintpallet for the targeted bulk density ranges used by the plasticresin industry.4.2.4 Box liner manufacturers to size their liners to aspecified volume dimension.4.2.5 Warehou

24、ses to provide space layout plans based ondimensions of the standard box/pallet unit.5. Basis of Classification5.1 The bulk box will contain about 1000 to 1600 lb (453.6to 725.7 kg) of plastic resins with typical bulk densities of 27to 39 lb/ft3(0.432 to 0.625 g/cm3).5.2 Minimum performance of the b

25、ulk box pallet unitduring pack out, storage, and transit will be specified by theuser.5.3 Total height of box, cap, and pallet (container height)equals 44 634-in. (1118 6 19 mm).5.4 Total width of pallet (container footprint width) equals45 614-in. (1143 6 6.35 mm).5.5 Total length of pallet (contai

26、ner footprint length) equals48 614-in. (1219 6 6.35 mm).5.6 Bulk box “freeboard” on all sides of the pallet will bespecified by the user.5.7 Corrugated fiberboard bulk boxes are normally used inthis application; the octagon-shaped box is preferred becauseof the superior strength/capacity weight over

27、 rectangular cor-rugated boxes.5.8 Wooden pallets are typically used in this application butmay be of other materials of construction; the required foot-print will allow the user an option to choose either four- ortwo-way entry.5.9 The eight corners of the octagon bulk box must besupported on top an

28、d on the bottom by the pallet; box cornersmust align top and bottom on deck boards of wooden pallets.6. Test Method and Retest6.1 The bulk density performance properties enumerated inthis classification may be estimated with Test Methods D 1895.7. Ordering Information7.1 The purchaser should select

29、the preferred permittedoptions and include the following information in procurementdocuments:7.1.1 Standard title, number, and date.7.1.2 Bulk density of the plastic resin to be packaged.7.1.3 Expected gross weight of packed out box and pallet.7.1.4 Form for deliveryassembled or knocked down.7.1.5 U

30、nitization requirements.7.1.6 Liner or bag requirements.7.1.7 Stacking, environmental, and shelf life requirements.7.1.8 Graphic requirements.7.1.9 Transport package requirements.8. Keywords8.1 bulk box; bulk package; containers by bulk density;paperboard containers; plastic resin; resin package; re

31、turnablebox system; transport packageD 6881/D 6881M 03 (2008)12ANNEX(Mandatory Information)A1. BULK BOX STANDARD CLASSIFICATION SUMMARYA1.1 Criteria in setting dimension limits include:A1.1.1 The height requirement is to insure that the doublestack container (normal fork truck load) will enter the o

32、ceancontainer that has an opening of 90 in. (2286 mm) at thecontainer entrance door.A1.1.2 The width requirement is to insure two containerswill fit side by side in truck vans and ocean containers withadequate space for fork truck loading. Inside ocean containerwidth equals 92 in. (2337 mm).A1.1.3 T

33、he width requirement is to insure the bulk box orpallet/skid may be suitable for use in multi-industry applica-tions (for example, the automotive and chemical drum indus-tries).A1.1.4 The length requirement is to insure the bulk box orpallet/skid may be suitable for use in multi-industry applica-tio

34、ns (for example, the automotive and chemical drum indus-tries).A1.1.5 The weight requirement is based on the volume ofthe bulk box and bulk density of the plastic resin.APPENDIX(Nonmandatory Information)X1. GENERAL USE AND GUIDANCEX1.1 The size requirements are based on being able to loadocean freig

35、ht containers as well as truck load vans using palletswith a two-way entry (no “pinwheeling” of the load isnecessary). User may specify pallets with four-way entry.X1.2 Since the box will be used by a wide variety of userswith different storage and transit requirements, each user mayutilize their ow

36、n performance standards and specifications.X1.3 Organizations that may be interested in this standardinclude:X1.3.1 Society of Plastic Engineers.X1.3.2 National Wooden Pallet and Container Association.X1.3.3 Technical Association of the Pulp and Paper Indus-try.X1.3.4 American Plastics CouncilAmeric

37、an ChemicalCouncil.X1.3.5 Society of Plastics Industries.D 6881/D 6881M 03 (2008)13Top, Length and Width ViewFIG. X1.1 Example of Bulk Box/Pallet Unit (Not to Scale)D 6881/D 6881M 03 (2008)14ASTM International takes no position respecting the validity of any patent rights asserted in connection with

38、 any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible techni

39、cal committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideratio

40、n at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harb

41、or Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).End ViewThree high stack of boxes and pallets showing deck board placement. See Fig. X1.1 for example of Width view.FIG. X1.2 Drawing 2 (Not to Scale)D 6881/D 6881M 03 (2008)15