ASTM D6751-2010 5625 Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels《适合于中间馏分燃料的生物柴油燃料(B100)混合贮藏的标准规范》.pdf

《ASTM D6751-2010 5625 Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels《适合于中间馏分燃料的生物柴油燃料(B100)混合贮藏的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM D6751-2010 5625 Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels《适合于中间馏分燃料的生物柴油燃料(B100)混合贮藏的标准规范》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D6751 10Standard Specification forBiodiesel Fuel Blend Stock (B100) for Middle DistillateFuels1This standard is issued under the fixed designation D6751; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last

2、 revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers biodiesel (B100) Grades S15and S500 for use as a blend component with middle distillatefuels.1.

3、2 This specification prescribes the required properties ofdiesel fuels at the time and place of delivery. The specificationrequirements may be applied at other points in the productionand distribution system when provided by agreement betweenthe purchaser and the supplier.1.3 Nothing in this specifi

4、cation shall preclude observanceof federal, state, or local regulations which may be morerestrictive.NOTE 1The generation and dissipation of static electricity can createproblems in the handling of distillate fuel oils with which biodiesel maybe blended. For more information on the subject, see Guid

5、e D4865.1.4 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.4.1 ExceptionIn Annex A1, the values stated in SI unitsare to be regarded as the standard. The values given inparentheses are for information only.2. Referenced Docum

6、ents2.1 ASTM Standards:2D93 Test Methods for Flash Point by Pensky-MartensClosed Cup TesterD130 Test Method for Corrosiveness to Copper from Pe-troleum Products by Copper Strip TestD189 Test Method for Conradson Carbon Residue of Pe-troleum ProductsD445 Test Method for Kinematic Viscosity of Transpa

7、rentand Opaque Liquids (and Calculation of Dynamic Viscos-ity)D524 Test Method for Ramsbottom Carbon Residue ofPetroleum ProductsD613 Test Method for Cetane Number of Diesel Fuel OilD664 Test Method for Acid Number of Petroleum Productsby Potentiometric TitrationD874 Test Method for Sulfated Ash fro

8、m Lubricating Oilsand AdditivesD974 Test Method for Acid and Base Number by Color-Indicator TitrationD975 Specification for Diesel Fuel OilsD976 Test Method for Calculated Cetane Index of DistillateFuelsD1160 Test Method for Distillation of Petroleum Productsat Reduced PressureD1266 Test Method for

9、Sulfur in Petroleum Products(Lamp Method)D1796 Test Method for Water and Sediment in Fuel Oils bythe Centrifuge Method (Laboratory Procedure)D2274 Test Method for Oxidation Stability of DistillateFuel Oil (Accelerated Method)D2500 Test Method for Cloud Point of Petroleum ProductsD2622 Test Method fo

10、r Sulfur in Petroleum Products byWavelength Dispersive X-ray Fluorescence SpectrometryD2709 Test Method for Water and Sediment in MiddleDistillate Fuels by CentrifugeD2880 Specification for Gas Turbine Fuel OilsD3117 Test Method for Wax Appearance Point of DistillateFuels3D3120 Test Method for Trace

11、 Quantities of Sulfur in LightLiquid Petroleum Hydrocarbons by Oxidative Microcou-lometryD3242 Test Method for Acidity in Aviation Turbine FuelD3828 Test Methods for Flash Point by Small Scale ClosedCup TesterD4057 Practice for Manual Sampling of Petroleum andPetroleum Products1This specification is

12、 under the jurisdiction of ASTM Committee D02 onPetroleum Products and Lubricants and is the direct responsibility of SubcommitteeD02.E0 on Burner, Diesel, Non-Aviation Gas Turbine, and Marine Fuels.Current edition approved Aug. 1, 2010. Published October 2010. Originallyapproved in 1999 as PS 12199

13、. Adopted as a standard in 2002 as D675102. Lastprevious edition approved in 2009 as D675109a. DOI: 10.1520/D6751-10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to

14、 the standards Document Summary page onthe ASTM website.3Withdrawn. The last approved version of this historical standard is referencedon www.astm.org.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocke

15、n, PA 19428-2959, United States.D4177 Practice for Automatic Sampling of Petroleum andPetroleum ProductsD4294 Test Method for Sulfur in Petroleum and PetroleumProducts by Energy Dispersive X-ray Fluorescence Spec-trometryD4530 Test Method for Determination of Carbon Residue(Micro Method)D4737 Test M

16、ethod for Calculated Cetane Index by FourVariable EquationD4865 Guide for Generation and Dissipation of StaticElectricity in Petroleum Fuel SystemsD4951 Test Method for Determination of Additive Ele-ments in Lubricating Oils by Inductively Coupled PlasmaAtomic Emission SpectrometryD5452 Test Method

17、for Particulate Contamination in Avia-tion Fuels by Laboratory FiltrationD5453 Test Method for Determination of Total Sulfur inLight Hydrocarbons, Spark Ignition Engine Fuel, DieselEngine Fuel, and Engine Oil by Ultraviolet FluorescenceD5771 Test Method for Cloud Point of Petroleum Products(Optical

18、Detection Stepped Cooling Method)D5772 Test Method for Cloud Point of Petroleum Products(Linear Cooling Rate Method)D5773 Test Method for Cloud Point of Petroleum Products(Constant Cooling Rate Method)D6217 Test Method for Particulate Contamination inMiddle Distillate Fuels by Laboratory FiltrationD

19、6300 Practice for Determination of Precision and BiasData for Use in Test Methods for Petroleum Products andLubricantsD6450 Test Method for Flash Point by Continuously ClosedCup (CCCFP) TesterD6469 Guide for Microbial Contamination in Fuels andFuel SystemsD6584 Test Method for Determination of Total

20、 Monoglyc-eride, Total Diglyceride, Total Triglyceride, and Free andTotal Glycerin in B-100 Biodiesel Methyl Esters by GasChromatographyD6890 Test Method for Determination of Ignition Delayand Derived Cetane Number (DCN) of Diesel Fuel Oils byCombustion in a Constant Volume ChamberD7039 Test Method

21、for Sulfur in Gasoline and Diesel Fuelby Monochromatic Wavelength Dispersive X-ray Fluores-cence SpectrometryD7397 Test Method for Cloud Point of Petroleum Products(Miniaturized Optical Method)2.2 Government Standard:40 CFR Part 79 Registration of Fuels and Fuel AdditivesSection 211(b) Clean Air Act

22、42.3 Other Documents:UOP 389 Trace Metals in Oils by Wet Ashing and ICP-OES5UOP 39191 Trace Metals in Petroleum Products or Organ-ics by AAS5EN 14110 Fat and oil derivativesFatty acid methyl esters(FAME)Determination of methanol content6EN 14112 Fat and oil derivativesFatty acid methyl esters(FAME)D

23、etermination of oxidation stability (Acceler-ated oxidation test)6EN 14538 Fat and oil derivativesFatty acid methyl esters(FAME)Determination of Ca, K, Mg and Na content byoptical emission spectral analysis with inductivelycoupled plasma (ICP OES)6EN 15751 Automotive fuels - Fatty acid methyl ester(

24、FAME) fuel and blends with diesel fuel - Determinationof oxidation stability by accelerated oxidation method63. Terminology3.1 Definitions:3.1.1 biodiesel, nfuel comprised of mono-alkyl esters oflong chain fatty acids derived from vegetable oils or animalfats, designated B100.3.1.1.1 Discussionbiodi

25、esel, as defined above, is regis-tered with the U.S. EPA as a fuel and a fuel additive underSection 211(b) of the Clean Air Act. There is, however, otherusage of the term biodiesel in the marketplace. Due to its EPAregistration and the widespread commercial use of the termbiodiesel in the U.S. marke

26、tplace, the term biodiesel will bemaintained for this specification.3.1.1.2 DiscussionBiodiesel is typically produced by areaction of a vegetable oil or animal fat with an alcohol such asmethanol or ethanol in the presence of a catalyst to yieldmono-alkyl esters and glycerin, which is removed. The f

27、inishedbiodiesel derives approximately 10 % of its mass from thereacted alcohol. The alcohol used in the reaction may or maynot come from renewable resources.3.1.2 biodiesel blend (BXX), nblend of biodiesel fuel withdiesel fuel oils.3.1.2.1 DiscussionIn the abbreviation BXX, the XX rep-resents the v

28、olume percentage of biodiesel fuel in the blend.3.1.3 biodiesel fuel, nsynonym for biodiesel.3.1.4 diesel fuel, nmiddle petroleum distillate fuel.3.1.5 free glycerin, na measure of the amount of glycerinremaining in the fuel.3.1.6 Grade S15 B100, na grade of biodiesel meetingASTM Specification D6751

29、 and having a sulfur specificationof 15 ppm maximum.3.1.7 Grade S500 B100, na grade of biodiesel meetingASTM Specification D6751 and having a sulfur specificationof 500 ppm maximum.3.1.8 middle distillate fuel, nkerosines and gas oils boil-ing between approximately 150C and 400C at normal atmo-spher

30、ic pressure and having a closed-cup flash point above38C.3.1.9 total glycerin, nthe sum of the free glycerin and theglycerin portion of any unreacted or partially reacted oil or fat.4Available from U.S. Government Printing Office Superintendent of Documents,732 N. Capitol St., NW, Mail Stop: SDE, Wa

31、shington, DC 20401.5Available from ASTM International, 100 Barr Harbor Drive, PO Box C700,West Conshohocken, PA. Visit theASTM website, www.astm.org, or contactASTMCustomer Service at serviceastm.org.6Available from the National CEN Members listed on the CEN website(www.cenorm.be) or from the CEN/TC

32、19 secretariat (astmnen.nl).D6751 1024. Requirements4.1 The biodiesel specified shall be mono-alkyl esters oflong chain fatty acids derived from vegetable oils and animalfats.4.2 Unless otherwise specified, samples for analysis shall betaken by the procedure described in Practices D4057 or D4177.4.3

33、 The biodiesel specified shall conform to the detailedrequirements shown in Table 1.NOTE 2A considerable amount of experience exists in the U.S. witha 20 % blend of biodiesel, primarily produced from soybean oil, with80 % diesel fuel (B20). Experience with biodiesel produced from animalfat and other

34、 oils is similar. Experience with B20 and lower blends in otherapplications is not as prevalent. Although biodiesel (B100) can be used,blends of over 20 % biodiesel with diesel fuel (B20) should be evaluatedon a case by case basis until further experience is available.NOTE 3The user should consult t

35、he equipment manufacturer orowners manual regarding the suitability of using biodiesel or biodieselblends in a particular engine or application.5. Test Methods5.1 The requirements enumerated in this specification shallbe determined in accordance with the following methods.5.1.1 Flash PointTest Metho

36、ds D93, except where othermethods are prescribed by law. Test Methods D3828 or D6450can also be used. The precision and bias of Test MethodsD3828 and D6450 with biodiesel is not known and is currentlyunder investigation. Test Methods D93 shall be the refereemethod.5.1.2 Water and SedimentTest Method

37、 D2709. TestMethod D1796 may also be used. Test Method D2709 shall bethe referee method. The precision and bias of these testmethods with biodiesel is not known and is currently underinvestigation.5.1.3 ViscosityTest Method D445.5.1.4 Sulfated AshTest Method D874.5.1.5 Oxidation StabilityTest Method

38、 EN 15751. TestMethod EN 14112 may also be used. See X1.18.1 for furtherinformation. Test Method EN 15751 shall be the referee testmethod.5.1.6 SulfurTest Method D5453. Test Method D7039 mayalso be used. Other test methods may also be suitable fordetermining up to 0.05 % (500 ppm) sulfur in biodiese

39、l fuelssuch as Test Methods D1266, D2622, D3120 and D4294 butmay provide falsely high results (see X1.5) although theirprecision and bias with biodiesel is unknown. Test MethodD5453 shall be the referee test method.5.1.7 CorrosionTest Method D130, 3 h test at 50C.5.1.8 Cetane NumberTest Method D613.

40、 Test MethodD6890 may also be used. Test Method D613 shall be thereferee method.5.1.9 Cloud PointTest Method D2500. Test MethodD5771, D5772, D5773,orD7397 may also be used. TestMethod D3117 may also be used because it is closely related.Test Method D2500 shall be the referee test method. Theprecisio

41、n and bias of Test Method D3117 for biodiesel is notknown and is currently under investigation.5.1.10 Acid NumberTest Method D664. Test MethodsD3242 or D974 may also be used. Test Method D664 shall bethe referee test method.TABLE 1 Detailed Requirements for Biodiesel (B100) (All Sulfur Levels)Proper

42、ty Test MethodAGrade S15LimitsGrade S500LimitsUnitsCalcium and Magnesium, combined EN 14538 5 max 5 max ppm (g/g)Flash point (closed cup) D93 93 min 93 min CAlcohol controlOne of the following must be met:1. Methanol content EN 14110 0.2 max 0.2 max mass %2. Flash point D93 130 min 130 min CWater an

43、d sediment D2709 0.050 max 0.050 max % volumeKinematic viscosity, 40C D445 1.9-6.0B1.96.0Bmm2/sSulfated ash D874 0.020 max 0.020 max % massSulfurCD5453 0.0015 max (15) 0.05 max (500) % mass (ppm)Copper strip corrosion D130 No. 3 max No. 3 maxCetane number D613 47 min 47 minCloud point D2500 ReportDR

44、eportDCCarbon residueED4530 0.050 max 0.050 max % massAcid number D664 0.50 max 0.50 max mg KOH/gCold soak filterability Annex A1 360 maxF360 maxFsecondsFree glycerin D6584 0.020 max 0.020 max % massTotal glycerin D6584 0.240 max 0.240 max % massPhosphorus content D4951 0.001 max 0.001 max % massDis

45、tillation temperature,Atmospheric equivalent temperature,90 % recoveredD1160 360 max 360 max CSodium and Potassium, combined EN 14538 5 max 5 max ppm (g/g)Oxidation stability EN 15751 3 minimum 3 minimum hoursAThe test methods indicated are the approved referee methods. Other acceptable methods are

46、indicated in 5.1.BSee X1.3.1. The 6.0 mm2/s upper viscosity limit is higher than petroleum based diesel fuel and should be taken into consideration when blending.COther sulfur limits can apply in selected areas in the United States and in other countries.DThe cloud point of biodiesel is generally hi

47、gher than petroleum based diesel fuel and should be taken into consideration when blending.ECarbon residue shall be run on the 100 % sample (see 5.1.11).FB100 intended for blending into diesel fuel that is expected to give satisfactory vehicle performance at fuel temperatures at or below 12C shall c

48、omply with a coldsoak filterability limit of 200 s maximum.D6751 1035.1.11 Carbon ResidueTest Method D4530. A100 %sample shall replace the 10 % residual, with percent residue inthe original sample reported using the 10 % residual calcula-tion (see X1.9.1). Test Methods D189 or D524 may also beused.

49、Test Method D4530 shall be the referee method.5.1.12 Total GlycerinTest Method D6584.5.1.13 Free GlycerinTest Method D6584.5.1.14 Phosphorus ContentTest Method D4951.5.1.15 Distillation Temperature, Reduced PressureTestMethod D1160.5.1.16 Calcium and Magnesium, combinedTest MethodEN 14538. Test Method UOP 389 may also be used. TestMethod EN 14538 shall be the referee test method.5.1.17 Sodium and Potassium, combinedTest MethodEN 14538. Test Method UOP 391 may also be used. TestMethod EN 14538 shall be the referee test metho