ASTM D6659-2001(2007) Standard Practice for Sampling and Preparation of Wet Blue for Physical and Chemical Tests《物理和化学试验用湿铬鞣革的取样和制备的标准实施规程》.pdf

《ASTM D6659-2001(2007) Standard Practice for Sampling and Preparation of Wet Blue for Physical and Chemical Tests《物理和化学试验用湿铬鞣革的取样和制备的标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM D6659-2001(2007) Standard Practice for Sampling and Preparation of Wet Blue for Physical and Chemical Tests《物理和化学试验用湿铬鞣革的取样和制备的标准实施规程》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 6659 01 (Reapproved 2007)Standard Practice forSampling and Preparation of Wet Blue for Physical andChemical Tests1This standard is issued under the fixed designation D 6659; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revi

2、sion, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers the sampling and preparation of wetblue for physical and chemical tests. The p

3、roduct is groupedinto lots that are randomly sampled in such a manner as toproduce a representative sample of the lot. This sample may beused to determine compliance of the lot with applicablespecification requirements, and on the basis of results, the lotmay be accepted or rejected in its entirety.

4、1.2 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Terminology2

5、.1 Definitions:2.1.1 lot (or batch), nunits of products from a single type,grade, class, size, and composition, manufactured under essen-tially the same conditions and time.2.1.1.1 DiscussionWet blue in formed lots should beproduced from: (1) Units of product of similar size and type.(2) Chromium ta

6、nning material obtained from the same pro-ducer (or functionally equivalent). (3)Asingle product method.(4) Sequential production batches.2.1.2 unit, na piece of wet blue in the form in which it ispurchased, such as a single hide, skin, or any part thereof.3. Significance and Use3.1 The sampling pro

7、cedures described in this practice havebeen designed to ensure random sampling of wet blue forphysical and chemical tests. Wet blue is a natural product andas such is subject to extensive variability. The physical andchemical properties vary considerably depending on locationon the hide, side, or sk

8、in from which the test sample is taken.Random sampling of specimens from a predefined location andorientation minimizes test bias and variability. This practicedefines these parameters.4. Conditioning4.1 Chemical and physical tests of wet blue, unless other-wise specified in the applicable test meth

9、od, specification, orprocurement document, shall be performed under standardatmospheric conditions, which is 50 6 4% relative humidity ata temperature of 23 6 1 C (73.4 6 2 F). If testing conditionsvary from this standard the actual conditions must be includedin the report of all such tests.5. Sampl

10、ing Procedure5.1 Prior to sampling, identify the product properly as a lotor batch.5.2 Select units from locations scattered throughout the lot,not from the same portion of the lot, such as a single pallet,carton, layer, etc. Take without regard to quality.5.2.1 The number of samples taken depends o

11、n the reliabil-ity of the test results, the deviation of the properties, and theerror of the testing procedure. The number of samples takenmay be at the discretion of the user and the related test methodand should also be recorded on the test report. It is recom-mended that 12 samples be taken for e

12、very 50,000 square feetof hide or skin. These 12 shall be considered a lot, or batch.NOTE 1By reason of the high moisture content of wet blue, samplesshould be taken after the wringing operation and immediately sealed inairtight plastic wrap. Store in a cool place until used.5.3 The standard locatio

13、n for sampling wet blue is thekidney area (designated as TEST AREA “a”inFig. 1).Sampling in the belly or shoulder area is only applicable if thatis the end product being sold or purchased:5.3.1 SkinsCut the test piece to the size and shaperequired for the tests to be made, with one edge parallel to

14、and1 in. (25.4 mm) from the backbone line, beginning 3 in. (76mm) from the root of the tail. Pieces shall be cut from only oneside of the backbone of each skin. The test area for skinscorresponds to area a for cattlehides of Fig. 1.5.3.2 CattlehidesThe location and size of cutting shall beas follows

15、:1This practice is under the jurisdiction ofASTM Committee D31 on Leather andis the direct responsibility of Subcommittee D31.02 on Wet Blue.Current edition approved Sept. 1, 2007. Published September 2007. Originallyapproved in 2001. Last previous edition approved in 2001 as D6659-01.1Copyright AST

16、M International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.3.2.1 Hides, Sides, Crops, Backs, and BendsCut the testpiece to the size and shape required for the test to be made,with one edge parallel to and 2 in. (51 mm) from the backboneline beginning 5 in.

17、 (127 mm) from the root of the tail. In mostinstances, test piece “a” may be cut 8 in. (203 mm) by 8 in.(203 mm). Sample double bends, belting butts, and hides ononly one side of the backbone (see Fig. 1, test area “a”).5.3.2.2 BelliesCut out the test piece, X, 5 in. (127 mm)wide and 7 in. (178 mm)

18、long with one long edge parallel toand 1 in. (25.4 mm) from the belly line, DF,inFig. 1. Locatethe test cutting at the middle of the piece midway betweenpoints D and F.5.3.2.3 Double ShouldersCut out the test piece, Y,5by7in. (127 by 178 mm) with a long edge parallel to and 1 in. (25.4mm) from the s

19、houlder line, BE. Locate the test cutting at themiddle of the piece between B and E.5.3.2.4 Cut out each test specimen with its long dimensionperpendicular to the backbone line, unless otherwise specifiedin the corresponding test method.5.3.2.5 When several specimens are required from eachpiece, cut

20、 them out in the following order beginning at the endnearest the tail: tensile strength and elongation (dumbbell),breaking strength (grab), bursting strength, stitch tear, shrink-age temperature, tongue tear, stiffness.5.3.2.6 When cutting specimens for physical tests, areasselected must be free fro

21、m visual defects such as cuts,scratches, and other obvious flaws.6. Sampling Preparation6.1 Time is crucial in the preparation of wet blue forchemical analysis. The following dicing procedure should bedone in 2 min. or less for each individual sample to preventsignificant moisture loss.6.1.1 Samples

22、 must be cut on a non-porous, non-absorbinghard surface using a clean sharp cutting tool, preferably with anew razor or scalpel blade. Avoid excess pressure on thesample, which could force moisture out of the wet blue.6.1.2 Samples should be cut into 3 to 5 mm squares andleaving no original cut edge

23、s.6.1.3 Immediately place diced samples into an airtight glassor plastic container. This container must be large enough topermit preparation of a composite sample by freely mixing lotsamples, and yet having a minimum amount of airspace toprevent evaporation.6.1.4 Store at room temperature, away from

24、 heat or directlight.7. Keywords7.1 blue stock; chemical tests; lot; physical tests; sampling;unit; wet blueFIG. 1 Location of Test AreaD 6659 01 (2007)2ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. U

25、sers of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed eve

26、ry five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible techn

27、ical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D 6659 01 (2007)3