ASTM D6405-1999(2009) 752 Standard Practice for Extraction of Tannins from Raw and Spent Materials《从原材料和用过的材料中提取单宁的标准实施规程》.pdf
《ASTM D6405-1999(2009) 752 Standard Practice for Extraction of Tannins from Raw and Spent Materials《从原材料和用过的材料中提取单宁的标准实施规程》.pdf》由会员分享,可在线阅读,更多相关《ASTM D6405-1999(2009) 752 Standard Practice for Extraction of Tannins from Raw and Spent Materials《从原材料和用过的材料中提取单宁的标准实施规程》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D 6405 99 (Reapproved 2009)Standard Practice forExtraction of Tannins from Raw and Spent Materials1This standard is issued under the fixed designation D 6405; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of
2、 last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers extracting the tannin from raw andspent materials. The water extract obtained by this method isu
3、sed to determine the tannin content of the original material.Analysis for total solids, soluble solids, and soluble non-tannins of the water extract from a material provides theinformation necessary to calculate the extractable tannin con-tent of that material. The types of materials typically analy
4、zedby this practice are products of plants such as woods, barks,leaves, nuts, fruits, roots, etc. and any of a wide variety ofby-products (spent materials) from industrial processes utiliz-ing plant products.1.2 The values stated in SI units are to be regarded as thestandard. The inch-pound units gi
5、ven in parentheses are forinformation only.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulato
6、ry limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D 1517 Terminology Relating to LeatherD 4903 Test Method for Total Solids and Water in VegetableTanning Material ExtractsD 4904 Practice for Cooling of Analytical SolutionsD 6401 Test Method for Determining Non-Tannins andTannin
7、in Extracts of Vegetable Tanning MaterialsD 6402 Test Method for Determining Soluble Solids andInsolubles in Extracts of Vegetable Tanning MaterialsD 6403 Test Method for Determining Moisture in Raw andSpent MaterialsD 6404 Practice for Sampling Vegetable Materials Contain-ing Tannin2.2 ALCA Methods
8、:A5 Extraction of Raw and Spent Materials33. Terminology3.1 Definitions:3.1.1 For definitions of general leather and tanning termsused in this practice refer to Terminology D 1517.3.1.2 raw materialany of the various parts of plants thatare used as a source of vegetable tannins.3.1.3 spent materialp
9、lant tissue by-products from indus-trial processes which may contain significant quantities ofvegetable tannins.3.1.4 tanninan astringent substance found in the variousparts of plants such as bark, wood, leaves, nuts, fruits, roots,etc.3.1.5 vegetable tanninsmixtures of substances (naturalproducts)
10、obtained from plant tissues by water extractionwhich have the chemical and physical properties necessary toconvert animal hides and skins into leather.4. Summary of Practice4.1 The sample of material to be analyzed for tannin contentis first brought to moisture equilibrium with the laboratoryatmosph
11、ere (that is, wet materials such as spent materials arefirst dried under ambient laboratory conditions) and thenground sufficiently to pass through a sieve. This ground sampleis then extracted with water in a steam-jacketed extractor.5. Significance and Use5.1 This practice provides a standard proce
12、dure for obtain-ing the water-soluble materials (including tannins) from anymaterial that can be prepared for and charged to the steam-jacketed extractor. The extraction solutions are then analyzedaccording to Test Methods D 4903, D 6401, and D 6402.6. Apparatus and Reagents6.1 Sieve, with circular
13、openings 1.27 cm (0.50 in.) indiameter.6.2 Sieve, with circular openings of 2 mm diameter (U.S.Std. Sieve Series No. 10).1This practice is under the jurisdiction of ASTM Committee D31 on Leather.This test method has been adapted from and is a replacement for Method A5 of theOfficial Methods of the A
14、merican Leather Chemists Association.Current edition approved April 1, 2009. Published July 2009. Originallyapproved in 1999. Last previous edition approved in 2004 as D 6405 99 (2004).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceast
15、m.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Official Methods of the American Leather Chemists Association. Availablefrom the American Leather Chemists Association, University of Cincinnati, P.O.Box 210014, Cincinnati, O
16、H 45221-0014.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.6.3 Glass Rods, soft glass stirring rods with rounded,fire-polished ends.6.4 Borosilicate Glass Wool, made of soft, pliable fibers.6.5 Steam-Jacketed, Borosilicate Glass Ex
17、traction Appara-tus, as described in Fig. 1. This apparatus may need to bespecial ordered and custom built by a laboratory glass-blowingmanufacturer.6.6 Tubing, flexible, chemical and heat resistant tubing ofappropriate size and length to fit onto the outlet tubes of theextractor apparatus. The tubi
18、ng from the extraction chamberoutlet must fit into the receiving flask.6.7 Clamps, Hoffman or similar type for use on the tubingextensions from the extractor outlets.6.8 Wiley Mill, or similar grinder.6.9 Balance, analytical balance which will weigh up to 100g with an accuracy of 6 0.1 mg (6 0.0001
19、g).6.10 Formaldehyde, 40 % solution.6.11 Toluene, assay $ 99.5 %6.12 Volumetric Flask, 1-L capacity for spent materials or2-L capacity for raw materials. ClassAflasks with a bulb in theneck (M.C.A. type) are especially suitable for this work.7. Preparation of Sample7.1 All of the sample, drawn as di
20、rected in Practice D 6404,shall first be ground in a rough grinder, or shredded, to pass asieve having round openings 1.27 cm (0.50 in.) in diameter.After this grinding, the sample shall be mixed and quartered, asdescribed in the Quartering Samples section of Practice D 6404until about 450 g (1 lb)
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD640519992009752STANDARDPRACTICEFOREXTRACTIONOFTANNINSFROMRAWANDSPENTMATERIALS 原材料 材料 提取 单宁 标准 实施
链接地址:http://www.mydoc123.com/p-522423.html