ASTM D6353-2006(2017)e1 6095 Standard Guide for Sampling Plan and Core Sampling for Prebaked Anodes Used in Aluminum Production《铝生产用预焙阳极的取样计划和芯取样的标准指南》.pdf
《ASTM D6353-2006(2017)e1 6095 Standard Guide for Sampling Plan and Core Sampling for Prebaked Anodes Used in Aluminum Production《铝生产用预焙阳极的取样计划和芯取样的标准指南》.pdf》由会员分享,可在线阅读,更多相关《ASTM D6353-2006(2017)e1 6095 Standard Guide for Sampling Plan and Core Sampling for Prebaked Anodes Used in Aluminum Production《铝生产用预焙阳极的取样计划和芯取样的标准指南》.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D6353 06 (Reapproved 2017)1Standard Guide forSampling Plan and Core Sampling for Prebaked AnodesUsed in Aluminum Production1This standard is issued under the fixed designation D6353; the number immediately following the designation indicates the year oforiginal adoption or, in the case
2、of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTESubsection 7.1.5 was corrected editorially in February 2017.1. Scope1.1 This guide covers sampling f
3、or prebaked carbon anodesused in the production of aluminum, and details procedures fortaking test samples from anode blocks. It covers equipment andprocedures for obtaining samples from anode blocks in amanner that does not destroy the block or prevent its subse-quent use as originally intended. Ho
4、wever, the user mustdetermine the subsequent use of the sampled anode blocks.Preferred locations for taking samples from single units ofanodes are covered in this guide.1.1.1 Information for sampling of shaped refractoryproducts, in general, is given in ISO 5022. This standard detailsthe statistical
5、 basis for sampling plans for acceptance testing ofa consignment or lot. Anodes used in the production ofaluminum have specific requirements for sampling and whilethe statistical basis for sampling given in ISO 5022 applies,further or modified requirements may also apply.1.2 The values stated in SI
6、units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health p
7、ractices and determine the applica-bility of regulatory limitations prior to use.NOTE 1The following ASTM standards are noted as sources of usefulinformation: Test Methods C559, C611, C651, C747, C1025, C1039, andE1225.2. Referenced Documents2.1 ASTM Standards:2C559 Test Method for Bulk Density by P
8、hysical Measure-ments of Manufactured Carbon and Graphite ArticlesC611 Test Method for Electrical Resistivity of ManufacturedCarbon and Graphite Articles at Room TemperatureC651 Test Method for Flexural Strength of ManufacturedCarbon and GraphiteArticles Using Four-Point Loading atRoom TemperatureC7
9、47 Test Method for Moduli of Elasticity and FundamentalFrequencies of Carbon and Graphite Materials by SonicResonanceC1025 Test Method for Modulus of Rupture in Bending ofElectrode GraphiteC1039 Test Methods for Apparent Porosity, Apparent Spe-cific Gravity, and Bulk Density of Graphite ElectrodesE1
10、225 Test Method for Thermal Conductivity of SolidsUsing the Guarded-Comparative-Longitudinal Heat FlowTechnique2.2 ISO Standards:3ISO 5022 Shaped refractory productsSampling and accep-tance testing3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 block, na carbon anode, a single
11、 unit.3.1.2 prebaked, na baked carbon article or block.3.1.3 sample, nthe portion of carbon obtained from ananode.3.1.4 test specimen, nan article prepared from a sample.4. Significance and Use4.1 Core sampling is an acceptable way of obtaining a testspecimen without destroying the usefulness of an
12、anode block.1This guide is under the jurisdiction of ASTM Committee D02 on PetroleumProducts, Liquid Fuels, and Lubricants and is the direct responsibility of Subcom-mittee D02.05 on Properties of Fuels, Petroleum Coke and Carbon Material.Current edition approved Jan. 1, 2017. Published February 201
13、7. Originallyapproved in 1998. Last previous edition approved in 2006 as D6353 06 (2011).DOI: 10.1520/D6353-06R17E01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to
14、 the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis
15、 international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TB
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD635320062017E16095STANDARDGUIDEFORSAMPLINGPLANANDCORESAMPLINGFORPREBAKEDANODESUSEDINALUMINUMPRODUCTION

链接地址:http://www.mydoc123.com/p-522262.html