ASTM D6352-2015 red 9678 Standard Test Method for Boiling Range Distribution of Petroleum Distillates in Boiling Range from 174&x2009 &xb0 C to 700&x2009 &xb0 C by Gas Chromatograp.pdf

《ASTM D6352-2015 red 9678 Standard Test Method for Boiling Range Distribution of Petroleum Distillates in Boiling Range from 174&x2009 &xb0 C to 700&x2009 &xb0 C by Gas Chromatograp.pdf》由会员分享，可在线阅读，更多相关《ASTM D6352-2015 red 9678 Standard Test Method for Boiling Range Distribution of Petroleum Distillates in Boiling Range from 174&x2009 &xb0 C to 700&x2009 &xb0 C by Gas Chromatograp.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D6352 14D6352 15Standard Test Method forBoiling Range Distribution of Petroleum Distillates inBoiling Range from 174 C to 700 C by GasChromatography1This standard is issued under the fixed designation D6352; the number immediately following the designation indicates the year oforiginal

2、adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This test method covers the determination of the boiling range dist

3、ribution of petroleum distillate fractions. The test methodis applicable to petroleum distillate fractions having an initial boiling point greater than 174 C (345 F) and a final boiling pointof less than 700 C (1292 F) (C10 to C90) at atmospheric pressure as measured by this test method.1.2 The test

4、 method is not applicable for the analysis of petroleum or petroleum products containing low molecular weightcomponents (for example naphthas, reformates, gasolines, crude oils). Materials containing heterogeneous components (forexample alcohols, ethers, acids, or esters) or residue are not to be an

5、alyzed by this test method. See Test Methods D3710, D2887,or D5307 for possible applicability to analysis of these types of materials.1.3 The values stated in SI units are to be regarded as standard. The values stated in inch-pound units are for information onlyand may be included as parenthetical v

6、alues.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatorylimitations prior to use.2. Referenc

7、ed Documents2.1 ASTM Standards:2D86 Test Method for Distillation of Petroleum Products at Atmospheric PressureD1160 Test Method for Distillation of Petroleum Products at Reduced PressureD2887 Test Method for Boiling Range Distribution of Petroleum Fractions by Gas ChromatographyD2892 Test Method for

8、 Distillation of Crude Petroleum (15-Theoretical Plate Column)D3710 Test Method for Boiling Range Distribution of Gasoline and Gasoline Fractions by Gas Chromatography (Withdrawn2014)3D4626 Practice for Calculation of Gas Chromatographic Response FactorsD5307 Test Method for Determination of Boiling

9、 Range Distribution of Crude Petroleum by Gas Chromatography (Withdrawn2011)3E355 Practice for Gas Chromatography Terms and RelationshipsE594 Practice for Testing Flame Ionization Detectors Used in Gas or Supercritical Fluid ChromatographyE1510 Practice for Installing Fused Silica Open Tubular Capil

10、lary Columns in Gas Chromatographs3. Terminology3.1 DefinitionsThis test method makes reference to many common gas chromatographic procedures, terms, and relationships.For definitions of these terms used in this test method, refer to Practices E355, E594, and E1510.3.2 Definitions of Terms Specific

11、to This Standard:1 This test method is under the jurisdiction ofASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of SubcommitteeD02.04.0H on Chromatographic Distribution Methods.Current edition approved Oct. 1, 2014July 1, 2015. Published Decemb

12、er 2014July 2015. Originally approved in 1998. Last previous edition approved in 20122014 asD6352 12.D6352 14. DOI: 10.1520/D6352-14.10.1520/D6352-15.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Stand

13、ardsvolume information, refer to the standards Document Summary page on the ASTM website.3 The last approved version of this historical standard is referenced on www.astm.org.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what chan

14、ges have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the offic

15、ial document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States13.2.1 area slice, nthe area resulting from the integration of the chromatographic detector signal within a s

16、pecified retentiontime interval. In area slice mode (see 6.4.2), peak detection parameters are bypassed and the detector signal integral is recordedas area slices of consecutive, fixed duration time intervals.3.2.2 corrected area slice, nan area slice corrected for baseline offset by subtraction of

17、the exactly corresponding area slicein a previously recorded blank (non-sample) analysis.3.2.3 cumulative corrected area, nthe accumulated sum of corrected area slices from the beginning of the analysis througha given retention time, ignoring any non-sample area (for example, solvent).3.2.4 final bo

18、iling point (FBP), nthe temperature (corresponding to the retention time) at which a cumulative corrected areacount equal to 99.5 % of the total sample area under the chromatogram is obtained.3.2.5 initial boiling point (IBP), nthe temperature (corresponding to the retention time) at which a cumulat

19、ive corrected areacount equal to 0.5 % of the total sample area under the chromatogram is obtained.3.2.6 slice rate, nthe time interval used to integrate the continuous (analog) chromatographic detector response during ananalysis. The slice rate is expressed in Hz (for example integrations or slices

20、 per second).3.2.7 slice time, nthe analysis time associated with each area slice throughout the chromatographic analysis. The slice timeis the time at the end of each contiguous area slice.3.2.8 total sample area, nthe cumulative corrected area, from the initial area point to the final area point,

21、where thechromatographic signal has returned to baseline after complete sample elution.3.3 AbbreviationsA common abbreviation of hydrocarbon compounds is to designate the number of carbon atoms in thecompound. A prefix is used to indicate the carbon chain form, while a subscripted suffix denotes the

22、 number of carbon atoms (forexample n-C10 for normal-decane, i-C14 for iso-tetradecane).4. Summary of Test Method4.1 The boiling range distribution determination by distillation is simulated by the use of gas chromatography.Anon-polar opentubular (capillary) gas chromatographic column is used to elu

23、te the hydrocarbon components of the sample in order of increasingboiling point.4.2 A sample aliquot is diluted with a viscosity reducing solvent and introduced into the chromatographic system. Samplevaporization is provided by separate heating of the point of injection or in conjunction with column

24、 oven heating.4.3 The column oven temperature is raised at a specified linear rate to affect separation of the hydrocarbon components in orderof increasing boiling point. The elution of sample components is quantitatively determined using a flame ionization detector. Thedetector signal is recorded a

25、s area slices for consecutive retention time intervals during the analysis.4.4 Retention times of known normal paraffin hydrocarbons, spanning the scope of the test method, are determined andcorrelated to their boiling point temperatures. The normalized cumulative corrected sample areas for each con

26、secutive recordedtime interval are used to calculate the boiling range distribution. The boiling point temperature at each reported percent offincrement is calculated from the retention time calibration.5. Significance and Use5.1 The boiling range distribution of medium and heavy petroleum distillat

27、e fractions provides an insight into the compositionof feed stocks and products related to petroleum refining processes (for example, hydrocracking, hydrotreating, visbreaking, ordeasphalting). The gas chromatographic simulation of this determination can be used to replace conventional distillation

28、methodsfor control of refining operations. This test method can be used for product specification testing with the mutual agreement ofinterested parties.5.2 This test method extends the scope of boiling range determination by gas chromatography to include medium and heavypetroleum distillate fractio

29、ns beyond the scope of Test Method D2887 (538 C).5.3 Boiling range distributions obtained by this test method have not been analyzed for correlation to those obtained by lowefficiency distillation, such as with Test Method D86 or D1160.6. Apparatus6.1 ChromatographThe gas chromatographic system used

30、 shall have the following performance characteristics:6.1.1 Carrier Gas Flow ControlThe chromatograph shall be equipped with carrier gas pressure or flow control capable ofmaintaining constant carrier gas flow control through the column throughout the column temperature program cycle.6.1.2 Column Ov

31、enCapable of sustained and linear programmed temperature operation from near ambient (for example,30 C to 35 C) up to 450 C.6.1.3 Column Temperature ProgrammerThe chromatograph shall be capable of linear programmed temperature operation upto 450 C at selectable linear rates up to 20 Cmin. The progra

32、mming rate shall be sufficiently reproducible to obtain the retentiontime repeatability of 0.1 min (6 s) for each component in the calibration mixture described in 7.5.D6352 1526.1.4 DetectorThis test method requires the use of a flame ionization detector (FID). The detector shall meet or exceed the

33、following specifications in accordance with Practice E594. The flame jet should have an orifice of approximately 0.05 mm to 0.070mm (0.020 in. to 0.030 in.).6.1.4.1 Operating Temperature100 C to 450 C.6.1.4.2 Sensitivity0.005 C/g carbon.6.1.4.3 Minimum Detectability1 10-11 g carbon/s.6.1.4.4 Linear

34、Range1066.1.4.5 Connection of the column to the detector shall be such that no temperature below the column temperature exists betweenthe column and the detector. Refer to Practice E1510 for proper installation and conditioning of the capillary column.6.1.5 Sample Inlet SystemAny sample inlet system

35、 capable of meeting the performance specification in 7.6 and 8.2.2 may beused. Programmable temperature vaporization (PTV) and cool on-column injection systems have been used successfully.6.2 MicrosyringeA microsyringe with a 23-gage or smaller stainless steel needle is used for on-column sample int

36、roduction.Syringes of 0.1 L to 10 L capacity are available.6.2.1 Automatic syringe injection is recommended to achieve best precision.6.3 ColumnThis test method is limited to the use of non-polar wall coated open tubular (WCOT) columns of high thermalstability (see Note 1). Glass, fused silica, and

37、stainless steel columns with 0.53 mm to 0.75 mm internal diameter have beensuccessfully used. Cross-linked or bonded 100 % dimethyl-polysiloxane stationary phases with film thickness of 0.10 m to 0.20m have been used. The column length and liquid phase film thickness shall allow the elution of at le

38、ast C90 n-paraffin (BP =700C). The column and conditions shall provide separation of typical petroleum hydrocarbons in order of increasing boiling pointand meet the column performance requirements of 8.2.1. The column shall provide a resolution between three (3) and ten (10)using the test method ope

39、rating conditions.NOTE 1Based on recent information that suggests that true boiling points (atmospheric equivalent temperatures) versus retention times for allcomponents do not fall on the same line, other column systems that can meet this criteria will be considered. These criteria will be specifie

40、d after a roundrobin evaluation of the test method is completed.6.4 Data Acquisition System:6.4.1 RecorderA0 mV to 1 mV range recording potentiometer or equivalent with a full-scale response time of 2 s or less maybe used. It is, however, not a necessity if an integrator/computer data system is used

41、.6.4.2 IntegratorMeans shall be provided for determining the accumulated area under the chromatogram. This can be done bymeans of an electronic integrator or computer-based chromatography data system. The integrator/computer system shall havenormal chromatographic software for measuring the retentio

42、n time and areas of eluting peaks (peak detection mode). In addition,the system shall be capable of converting the continuously integrated detector signal into area slices of fixed duration. Thesecontiguous area slices, collected for the entire analysis, are stored for later processing. The electron

43、ic range of theintegrator/computer (for example 1 V, 10 V) shall be operated within the linear range of the detector/electrometer system used.NOTE 2Some gas chromatographs have an algorithm built into their operating software that allows a mathematical model of the baseline profile tobe stored in me

44、mory. This profile is automatically subtracted from the detector signal on subsequent sample runs to compensate for the column bleed.Some integration systems also store and automatically subtract a blank analysis from subsequent analytical determinations.7. Reagents and Materials7.1 Carrier GasHeliu

45、m, hydrogen, or nitrogen of high purity. The use of alternative carrier gases hydrogen and nitrogen isdescribed in Appendix X2. (WarningHelium and nitrogen are compressed gases under high pressure) Additional purificationis recommended by the use of molecular sieves or other suitable agents to remov

46、e water, oxygen, and hydrocarbons. Availablepressure shall be sufficient to ensure a constant carrier gas flow rate.7.2 HydrogenHydrogen of high purity (for example, hydrocarbon free) is used as fuel for the FID. Hydrogen can also be usedas the carrier gas. (WarningHydrogen is an extremely flammable

47、 gas under high pressure).7.3 AirHigh purity (for example, hydrocarbon free) compressed air is used as the oxidant for the FID. (WarningCompressed air is a gas under high pressure and supports combustion).7.4 SolventsUnless otherwise indicated, it is intended that all solvents conform to the specifi

48、cations of the Committee onAnalytical Reagents of the American Chemical Society where such specifications are available.4 Other grades may be used,provided it is first ascertained that the solvent is of sufficiently high purity to permit its use without lessening the accuracy of thedetermination.7.4

49、.1 Carbon Disulfide (CS2)(99+ % pure) is used as a viscosity-reducing solvent and as a means of reducing mass of sampleintroduced onto the column to ensure linear detector response and reduced peak skewness. It is miscible with asphaltic4 Reagent Chemicals, American Chemical Society Specifications, American Chemical Society, Washington, DC. For Suggestions on the testing of reagents not listed bythe American Chemical Society, see Annual Standards for Laboratory Chemicals, BDH Ltd., Poole, Dorset, U.K., and the United States