ASTM D6321 D6321M-2013 red 2421 Standard Practice for the Evaluation of Machine Washable T-Shirts《可机洗的T恤衫评价的标准实施规程》.pdf

《ASTM D6321 D6321M-2013 red 2421 Standard Practice for the Evaluation of Machine Washable T-Shirts《可机洗的T恤衫评价的标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM D6321 D6321M-2013 red 2421 Standard Practice for the Evaluation of Machine Washable T-Shirts《可机洗的T恤衫评价的标准实施规程》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D6321 98 (Reapproved 2004)D6321/D6321M 13Standard Practice forthe Evaluation of Machine Washable T-Shirts1This standard is issued under the fixed designation D6321;D6321/D6321M; the number immediately following the designation indicatesthe year of original adoption or, in the case of re

2、vision, the year of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers test methods and procedures used to evaluate important characteristics of mac

3、hine washable T-shirts.T-shirts may be made of knitted fabric composed of any textile fiber(s) or blend of fibers and intended to be used as underwearor as an outer garment.1.2 T-shirts characteristics may be assessed either as a final product or at any intermediate processing stage.1.3 This practic

4、e excludes T-shirts intended for hand washing or dry cleaning care.1.4 The values stated in either SI units or inch-pound units are to be regarded separately as the standard. The values given inparentheses are provided for information only.stated in each system may not be exact equivalents; therefor

5、e, each system shall beused independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standar

6、ds to establish appropriate safety and health practices and determine the applicability of regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD1776 Practice for Conditioning and Testing TextilesD3786 Test Method for Bursting Strength of

7、 Textile FabricsDiaphragm Bursting Strength Tester MethodD3787 Test Method for Bursting Strength of TextilesConstant-Rate-of-Traverse (CRT) Ball Burst TestD3887 Specification for Tolerances for Knitted FabricsD3940 Test Method for Bursting Strength (Load) and Elongation of Sewn Seams of Knit or Wove

8、n Stretch Textile Fabrics(Withdrawn 1995)3D4154 Performance Specification for Mens and Boys Knitted and Woven Beachwear and Sports Shirt FabricsD4156 Performance Specification for Womens and Girls Knitted Sportswear FabricsD7022 Terminology Relating to Apparel2.2 AATCC Test Methods:4Evaluation Proce

9、dure 1, Gray Scale for Color ChangeEvaluation Procedure 2, Gray Scale for StainingEvaluation Procedure 7, Instrumental Assessment of the Change in Color of a Textile SpecimenMethod 107, Colorfastness to WaterMethod 150, Dimensional Changes in Automatic of Garments after Home Laundering of GarmentsMe

10、thod 172, Colorfastness to Powered Non-Chlorine Bleach in Home LaunderingMethod 179, Skewness Change in Fabric and Garment Twist in Fabrics and Garments After Resulting from Automatic HomeLaundering2.3 Other Documents:A Glossary of AATCC Standard Terminology4Standardization of Home Laundry TextTest

11、Conditions41 This practice is under the jurisdiction of ASTM Committee D13 on Textiles, and is the direct responsibility of Subcommittee D13.61 on Apparel.Current edition approved Oct. 1, 2004March 1, 2013. Published November 2004April 2013. Originally approved in 1998. Last previous edition approve

12、d in 19982004as D6321 98.D6321 98(2004). DOI: 10.1520/D6321-98R04.10.1520/D6321_D6321M-13.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summ

13、ary page on the ASTM website.3 The last approved version of this historical standard is referenced on www.astm.org.4 Available from AATCC, PO Box 12215, Research Triangle Park, NC 27709.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication o

14、f what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considere

15、d the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States13. Terminology3.1 Definitions:3.1.1 T-shirt, na knitted garment, typically constructed of jersey or 1 by 1 rib fabric, used as either an undergarment or as anoute

16、r casual top with a rib collar, hemmed sleeves and bottom, and a body configuration that resembles the letter “T”.3.1.1.1 DiscussionT-shirts may have either crew or v-neck styles; short or long sleeve lengths, and be adorned with appliques, embroidery, or garmentprinting or combinations of adornment

17、s. Henley and polo-styles shirts are excluded.3.1.2 For definitions of other textile terms used in this standard, refer to terminology in Terminology D123 and Glossary ofAATCC Standard Terminology.3.1 For all terminology relating to D13.61 refer to Terminology D7022.3.1.1 The following terms are rel

18、evant to this standard: T-shirt.3.1.2 For definitions of other textile terms used in this standard, refer to terminology in Terminology D123 and Glossary ofAATCC Standard Terminology.4. Significance and Use4.1 This practice may be used to evaluate pertinent characteristics of washable T-shirts.4.2 T

19、-shirts may be subject to extra processes such as garment dyeing, garment washing, printing, application of embroideryor trims. An individual process or combination or processes may affect the performance of the final product.4.3 This practice may be used by mutual agreement between the purchaser an

20、d the supplier to establish purchasingspecifications.5. Sampling, Selection, and Number of Specimens5.1 Lot SampleTake a lot sample as directed in an applicable material specification or as agreed between purchaser andsupplier, such as an agreement to take at random some fixed number of shipping con

21、tainers or garments from each lot.5.2 Laboratory SampleFrom each lot sampling unit, take five T-shirts to be used as the laboratory sample.5.3 Test SpecimenFrom each laboratory sample, two T-shirts are to be tested as-received and two T-shirts that are to belaundered. The fifth T-shirt is to be reta

22、ined as a control specimen and not tested.6. Fabric Performance Characteristics6.1 Evaluate fabric designated for T-shirt manufacture using Specification D3887, D3787, Performance Specification D4154,or Performance Specification D4156 as appropriate.7. Garment Performance Characteristics7.1 Assessme

23、nts Prior to Machine Laundering (As-Received State):7.1.1 Condition T-shirts in standard atmospheres for testing 20 6 3C (7070 6 2F)2F and 65 6 2 % RH according toPractice D1776 for 4 hrs.7.1.2 Shade DifferenceExamine each of the four T-shirts for shade difference, garment panel-to-panel, using AATC

24、CEvaluation Procedure 1 or 7.NOTE 1Difference results may be obtained when using the subjecting assessment in AATCC Evaluation Procedure 1 when using the instrumentalassessment in AATCC Evaluation Procedure 7.7.1.3 DefectsExamine the four T-shirts for needle cutting, seam appearance, surface irregul

25、arities, or any other defect andrecord the information.7.1.4 Seam PerformanceDetermine seam performance for the two as-received T-shirts as directed in Test Method D3940.7.1.5 Bursting ForceIf the fabric is not available for 6.1, determine bursting strength on the as-received T-shirts using D3787or

26、D3786.7.2 Specimen Preparation Prior to Laundering:7.2.1 Condition T-shirts to the standard atmospheres of 20 6 3C (7070 6 2F)2F and 65 % RH as specified in PracticeD1776 for at least 4 h.7.2.2 Lay the two T-shirts designated for laundering on a flat surface without tension, aligning sides and sleev

27、es and smoothingto minimize folds and wrinkles.7.2.3 Mark the dimensions to be measured with an indelible marking pen.7.2.3.1 For garment dimensional change, mark the locations according toAATCC TM 150 and as shown in Fig. 1 using a plasticor metal tape graduated in increments of millimetres (116 in

28、.):in.:D6321/D6321M 1327.2.3.2 Chest WidthPlace marks “A1” and “A2” 125 mm (5.0 in)5.0 in below each armhole seam. This is Distance “A”.Measure and record the distance across the chest to the nearest mm (116 in.).in.7.2.3.3 Front LengthFold the T-shirts in half lengthwise, back-to-back, matching sho

29、ulder and neck band seams. Lay thefolded T-shirts flat on a smooth surface. Place marks “B1” and “B2” 25 mm (1 in.)1 in. below the center neck band and 25 mm(1 in.)1 in. above the bottom hem. This is Distance “B”. Measure and record the distance between the upper and lower marksto the nearest mm (11

30、6 in.).in.7.2.3.4 Sleeve LengthPlace two T-shirts flat on a smooth surface. Mark the distance between the upper shoulder joining to thelower edge of the sleeve hem. This is Distance “C”. Measure and record the distance between the marked shoulder seam and thehem edge to the measure mm (116). .7.2.3.

31、5 Sleeve SeamPlace T-shirts flat on a smooth surface. Measure and record the distance between the upper shoulderjoining and the underarm seam intersection to the nearest mm (116 in.).in. This measurement is Distance “D”.7.2.3.6 Sleeve OpeningPlace T-shirts flat with the sleeves folded. Measure and r

32、ecord the distance between the upper edgeof the sleeve hem to the lower edge of the sleeve on the outer edge to the nearest mm (116 in.).in. This is Distance “E”. Themeasured distance should be doubled and recorded.7.2.3.7 Neck OpeningGrasp the neck band at the center back and the center front, form

33、ing a folded edge. Measure across thefolded band. This is Distance “F”. The measured distance should be doubled and recorded.7.2.4 Skewness ChangeMark the T-shirts according to AATCC Test Method 179, marking Option 3. See Fig. 2.7.2.5 Colorfastness to WaterFor dyed or printed T-shirts, prepare speci

34、mens for colorfastness to water according to AATCCTest Method 107.7.3 Laundering Conditions:7.3.1 Wash and dry the two T-shirts designated for laundering using the information on the care label and the applicableprocedure inAATCC Test Method 150. Use washing and drying conditions that conform to tho

35、se given in theAATCC monograph(see 2.3).NOTE 1Refer to AATCC Test Method 150.FIG. 1 Dimensional Change Marking LocationRefer to AATCC Test Method, 179 Marking, Option 2: AB = Before Laundering and AB or A“B = After laundering.FIG. 2 T-Shirt Skewness Change, Marking LocationsD6321/D6321M 1337.3.2 If

36、colorfastness to non-chlorine bleach is specified on the care label, use AATCC Test Method 172. For chlorine bleachcolorfastness, follow bleach manufacturers recommendations for volume of use and the sequence of addition and the care labelinstructions on the T-shirt or requirements agreed upon betwe

37、en the purchaser and supplier.7.4 Assessment after Machine Laundering:7.4.1 Dimensional ChangeMeasure the dimensional change distances after laundering and calculate percent dimensionalchange as directed in AATCC Test Method 150.7.4.2 Skewness ChangeMeasure the marked distances after laundering and

38、calculate percent skewness change according tothe AATCC Test Method 179, Option 3.7.4.3 StainingGrade staining of a dyed or printed T-shirts by using AATCC Test Method 107 and Evaluation Procedure 2. Ifmultifiber or crock square swatches were sewn on the T-shirts before laundering, evaluate the stai

39、ning performance using AATCCEvaluation Procedure 2.7.4.4 Shade DifferenceDetermine shade differences. Rate change of color on dyed or printed T-shirts from panel to panel andagainst the original T-shirt. Rate staining using AATCC Evaluation Procedure 2.7.4.5 DefectsExamine T-shirts for defect agreed

40、 upon by the purchaser and the supplier.7.4.6 Seam PerformanceAssess seam failure as directed in Test Method D3940.8. Report8.1 State that the specimens were tested as directed in Practice D6321. Describe the identification of the T-shirt material andthe method of sampling used.8.2 Report the follow

41、ing information:8.2.1 The number of T-shirts tested, and8.2.2 The performance characteristics assessed and the results of each.9. Conformance9.1 When the purchaser and supplier have agreed upon specific requirements for the characteristics assessed, the T-shirts thatfail to meet the requirements may

42、 be rejected.10. Keywords10.1 T-shirtsASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the r

43、iskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn.Your comments are invited either for revision of th

44、is standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake

45、 your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D6321/D6321M 134