ASTM D6300-2016a red 3179 Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants《测定用于石油产品和润滑剂试验方法的精度和偏差数据的标准实施.pdf

《ASTM D6300-2016a red 3179 Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants《测定用于石油产品和润滑剂试验方法的精度和偏差数据的标准实施.pdf》由会员分享，可在线阅读，更多相关《ASTM D6300-2016a red 3179 Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants《测定用于石油产品和润滑剂试验方法的精度和偏差数据的标准实施.pdf（55页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D6300 16D6300 16a An American National StandardStandard Practice forDetermination of Precision and Bias Data for Use in TestMethods for Petroleum Products and Lubricants1This standard is issued under the fixed designation D6300; the number immediately following the designation indicates

2、 the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.INTRODUCTIONBoth Research Report RR:D02-1007,2 Manual on De

3、termining Precision Data for ASTM Methodson Petroleum Products and Lubricants2 and the ISO 4259, benefitted greatly from more than 50 yearsof collaboration between ASTM and the Institute of Petroleum (IP) in the UK. The more recent workwas documented by the IP and has become ISO 4259.ISO 4259 encomp

4、asses both the determination of precision and the application of such precisiondata. In effect, it combines the type of information in RR:D02-10072 regarding the determination ofthe precision estimates and the type of information in Practice D3244 for the utilization of test data.The following pract

5、ice, intended to replace RR:D02-1007,2 differs slightly from related portions of theISO standard.1. Scope*1.1 This practice covers the necessary preparations and planning for the conduct of interlaboratory programs for thedevelopment of estimates of precision (determinability, repeatability, and rep

6、roducibility) and of bias (absolute and relative), andfurther presents the standard phraseology for incorporating such information into standard test methods.1.2 This practice is generally limited to homogeneous products with which serious sampling problems do not normally arise.1.3 This practice ma

7、y not be suitable for solid or semisolid products such as petroleum coke, industrial pitches, paraffin waxes,greases, or solid lubricants when the heterogeneous properties of the substances create sampling problems. In such instances, usePractice E691 or consult a trained statistician.2. Referenced

8、Documents2.1 ASTM Standards:3D3244 Practice for Utilization of Test Data to Determine Conformance with SpecificationsD3606 Test Method for Determination of Benzene and Toluene in Finished Motor and Aviation Gasoline by Gas Chromatog-raphyD6708 Practice for Statistical Assessment and Improvement of E

9、xpected Agreement Between Two Test Methods that Purportto Measure the Same Property of a MaterialD7915 Practice for Application of Generalized Extreme Studentized Deviate (GESD) Technique to Simultaneously IdentifyMultiple Outliers in a Data SetE29 Practice for Using Significant Digits in Test Data

10、to Determine Conformance with SpecificationsE177 Practice for Use of the Terms Precision and Bias in ASTM Test MethodsE456 Terminology Relating to Quality and StatisticsE691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method1 This practice is under the juris

11、diction of ASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricantsand is the direct responsibility of SubcommitteeD02.94 on Coordinating Subcommittee on Quality Assurance and Statistics.Current edition approved April 1, 2016July 1, 2016. Published April 2016August 2016. Originally app

12、roved in 1998. Last previous edition approved in 20152016 asD6300 15.D6300 16. DOI: 10.1520/D6300-16.10.1520/D6300-16A.2 Supporting data have been filed at ASTM International Headquarters and may be obtained by requesting Research Report RR:D02-1007.3 For referencedASTM standards, visit theASTM webs

13、ite, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indicatio

14、n of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be consid

15、ered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States12.2 ISO Standards:ISO 4259 Petroleum Products-Determination and Application of Precision Data

16、in Relation to Methods of Test43. Terminology3.1 Definitions:3.1.1 analysis of variance (ANOVA), ntechnique that enables the total variance of a method to be broken down into itscomponent factors. ISO 42593.1.2 bias, nthe difference between the expectation of the test results and an accepted referen

17、ce value.3.1.2.1 DiscussionThe term “expectation” is used in the context of statistics terminology, which implies it is a “statistical expectation.” E1773.1.3 between-method bias (relative bias), na quantitative expression for the mathematical correction that can statisticallyimprove the degree of a

18、greement between the expected values of two test methods which purport to measure the same property.D67083.1.4 degrees of freedom, nthe divisor used in the calculation of variance, one less than the number of independent results.3.1.4.1 DiscussionThis definition applies strictly only in the simplest

19、 cases. Complete definitions are beyond the scope of this practice. ISO 42593.1.5 determinability, na quantitative measure of the variability associated with the same operator in a given laboratoryobtaining successive determined values using the same apparatus for a series of operations leading to a

20、 single result; it is definedas that difference between two such single determined values as would be exceeded in the long run in only one case in 20 in thenormal and correct operation of the test method.3.1.5.1 DiscussionThis definition implies that two determined values, obtained under determinabi

21、lity conditions, which differ by more than thedeterminability value should be considered suspect. If an operator obtains more than two determinations, then it would usually besatisfactory to check the most discordant determination against the mean of the remainder, using determinability as the criti

22、caldifference (1).53.1.6 mean square, nin analysis of variance, sum of squares divided by the degrees of freedom. ISO 42593.1.7 normal distribution, nthe distribution that has the probability function x, such that, if x is any real number, theprobability density isfx!51/!2!21/2exp2x 2! 2/22# (1)NOTE

23、 1 is the true value and is the standard deviation of the normal distribution ( 0). ISO 42593.1.8 outlier, na result far enough in magnitude from other results to be considered not a part of the set. RR:D02100723.1.9 precision, nthe degree of agreement between two or more results on the same propert

24、y of identical test material. In thispractice, precision statements are framed in terms of repeatability and reproducibility of the test method.3.1.9.1 DiscussionThe testing conditions represented by repeatability and reproducibility should reflect the normal extremes of variability underwhich the t

25、est is commonly used. Repeatability conditions are those showing the least variation; reproducibility, the usualmaximum degree of variability. Refer to the definitions of each of these terms for greater detail.RR:D02100723.1.10 random error, nthe chance variation encountered in all test work despite

26、 the closest control of variables.RR:D02100723.1.11 repeatability, nthe quantitative expression of the random error associated with the same operator in a given laboratoryobtaining repetitive results by applying the same test method with the same apparatus under constant operating conditions on4 Ava

27、ilable from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http:/www.ansi.org.5 The bold numbers in parentheses refers to the list of references at the end of this standard.D6300 16a2identical test material within short intervals of time. It is defined a

28、s the difference between two such results at the 95 % confidencelevel. RR:D02100723.1.11.1 DiscussionInterpret as the value equal to or below which the absolute difference between two single test results obtained in the aboveconditions may expect to lie with a probability of 95 %. ISO 42593.1.11.2 D

29、iscussionThe difference is related to the repeatability standard deviation but it is not the standard deviation or its estimate. RR:D02100723.1.12 reproducibility, na quantitative expression of the random error associated with different operators from differentlaboratories using different apparatus,

30、 each obtaining a single result by applying the same test method on an identical test sample.It is defined as the 95 % confidence limit for the difference between two such single and independent results.3.1.12.1 DiscussionInterpret as the value equal to or below which the absolute difference between

31、 two single test results on identical material obtainedby operators in different laboratories, using the standardized test, may be expected to lie with a probability of 95 %. ISO 42593.1.12.2 DiscussionThe difference is related to the reproducibility standard deviation but is not the standard deviat

32、ion or its estimate. RR:D02100723.1.12.3 DiscussionIn those cases where the normal use of the test method does not involve sending a sample to a testing laboratory, either becauseit is an in-line test method or because of serious sample instabilities or similar reasons, the precision test for obtain

33、ingreproducibility may allow for the use of apparatus from the participating laboratories at a common site (several common sites, iffeasible). The statistical analysis is not affected thereby. However, the interpretation of the reproducibility value will be affected,and therefore, the precision stat

34、ement shall, in this case, state the conditions to which the reproducibility value applies.3.1.13 standard deviation, nmeasure of the dispersion of a series of results around their mean, equal to the square root of thevariance and estimated by the positive square root of the mean square. ISO 42593.1

35、.14 sum of squares, nin analysis of variance, sum of squares of the differences between a series of results and their mean.ISO 42593.1.15 variance, na measure of the dispersion of a series of accepted results about their average. It is equal to the sum of thesquares of the deviation of each result f

36、rom the average, divided by the number of degrees of freedom. RR:D02100723.1.16 variance, between-laboratory, nthat component of the overall variance due to the difference in the mean valuesobtained by different laboratories. ISO 42593.1.16.1 DiscussionWhen results obtained by more than one laborato

37、ry are compared, the scatter is usually wider than when the same number of testsare carried out by a single laboratory, and there is some variation between means obtained by different laboratories. Differencesin operator technique, instrumentation, environment, and sample “as received” are among the

38、 factors that can affect the betweenlaboratory variance. There is a corresponding definition for between-operator variance.3.1.16.2 DiscussionThe term “between-laboratory” is often shortened to “laboratory” when used to qualify representative parameters of the dispersionof the population of results,

39、 for example as “laboratory variance.”3.2 Definitions of Terms Specific to This Standard:3.2.1 determination, nthe process of carrying out a series of operations specified in the test method whereby a single valueis obtained.D6300 16a33.2.2 operator, na person who carries out a particular test.3.2.3

40、 probability density function, nfunction which yields the probability that the random variable takes on any one of itsadmissible values; here, we are interested only in the normal probability.3.2.4 result, nthe final value obtained by following the complete set of instructions in the test method.3.2

41、.4.1 DiscussionIt may be obtained from a single determination or from several determinations, depending on the instructions in the method. Whenrounding off results, the procedures described in Practice E29 shall be used.4. Summary of Practice4.1 Adraft of the test method is prepared and a pilot prog

42、ram can be conducted to verify details of the procedure and to estimateroughly the precision of the test method.4.1.1 If the responsible committee decides that an interlaboratory study for the test method is to take place at a later point intime, an interim repeatability is estimated by following th

43、e requirements in 6.2.1.4.2 A plan is developed for the interlaboratory study using the number of participating laboratories to determine the number ofsamples needed to provide the necessary degrees of freedom. Samples are acquired and distributed. The interlaboratory study isthen conducted on an ag

44、reed draft of the test method.4.3 The data are summarized and analyzed. Any dependence of precision on the level of test result is removed bytransformation. The resulting data are inspected for uniformity and for outliers. Any missing and rejected data are estimated. Thetransformation is confirmed.

45、Finally, an analysis of variance is performed, followed by calculation of repeatability, reproducibility,and bias. When it forms a necessary part of the test procedure, the determinability is also calculated.5. Significance and Use5.1 ASTM test methods are frequently intended for use in the manufact

46、ure, selling, and buying of materials in accordance withspecifications and therefore should provide such precision that when the test is properly performed by a competent operator, theresults will be found satisfactory for judging the compliance of the material with the specification. Statements add

47、ressing precisionand bias are required in ASTM test methods. These then give the user an idea of the precision of the resulting data and itsrelationship to an accepted reference material or source (if available). Statements addressing determinability are sometimesrequired as part of the test method

48、procedure in order to provide early warning of a significant degradation of testing quality whileprocessing any series of samples.5.2 Repeatability and reproducibility are defined in the precision section of every Committee D02 test method. Determinabilityis defined above in Section 3. The relations

49、hip among the three measures of precision can be tabulated in terms of their differentsources of variation (see Table 1).5.2.1 When used, determinability is a mandatory part of the Procedure section. It will allow operators to check their techniquefor the sequence of operations specified. It also ensures that a result based on the set of determined values is not subject to excessivevariability from that source.5.3 A bias statement furnishes guidelines on the relationship between a set of test results and a related set of ac