ASTM D6155-2015 2631 Standard Specification for Nontraditional Coarse Aggregates for Bituminous Paving Mixtures《沥青铺路混合料用非传统型粗集料的标准规格》.pdf

《ASTM D6155-2015 2631 Standard Specification for Nontraditional Coarse Aggregates for Bituminous Paving Mixtures《沥青铺路混合料用非传统型粗集料的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM D6155-2015 2631 Standard Specification for Nontraditional Coarse Aggregates for Bituminous Paving Mixtures《沥青铺路混合料用非传统型粗集料的标准规格》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D6155 15Standard Specification forNontraditional Coarse Aggregates for Bituminous PavingMixtures1This standard is issued under the fixed designation D6155; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of la

2、st revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the use of coarse aggregatesnot traditionally used in bituminous paving mixtures. Thesenontrad

3、itional aggregates can be described as any aggregateother than those described in Specifications D692, D693,D1139, and D5106, (crushed stone, crushed hydraulic-cementconcrete, crushed blast-furnace slag, steel furnace slag, andcrushed gravel) suitable for use in bituminous paving mixtures,as describ

4、ed in Specifications D3515 or D4215.1.2 The text of this specification references notes andfootnotes that provides explanatory material. These notes andfootnotes (excluding those in tables and figures) shall not beconsidered as requirements of the specification.1.3 The values stated in SI units are

5、to be regarded asstandard. No other units of measurement are included in thisstandard.NOTE 1Sieve size is identified by its standard designation in Speci-fication E11. The alternative designation given in parentheses is forinformation only and does not represent a different standard sieve size.1.4 T

6、his standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Docume

7、nts2.1 ASTM Standards:2C29/C29M Test Method for Bulk Density (“Unit Weight”)and Voids in AggregateC88 Test Method for Soundness of Aggregates by Use ofSodium Sulfate or Magnesium SulfateC125 Terminology Relating to Concrete and Concrete Ag-gregatesC131 Test Method for Resistance to Degradation of Sm

8、all-Size Coarse Aggregate by Abrasion and Impact in the LosAngeles MachineC136 Test Method for Sieve Analysis of Fine and CoarseAggregatesC142 Test Method for Clay Lumps and Friable Particles inAggregatesC294 Descriptive Nomenclature for Constituents of Con-crete AggregatesD8 Terminology Relating to

9、 Materials for Roads and Pave-mentsD75 Practice for Sampling AggregatesD448 Classification for Sizes of Aggregate for Road andBridge ConstructionD692 Specification for Coarse Aggregate for BituminousPaving MixturesD693 Specification for Crushed Aggregate for MacadamPavements (Withdrawn 2008)3D1139 S

10、pecification for Aggregate for Single or MultipleBituminous Surface TreatmentsD2489 Practice for Estimating Degree of Particle Coating ofBituminous-Aggregate MixturesD3319 Practice for the Accelerated Polishing of AggregatesUsing the British WheelD3515 Specification for Hot-Mixed, Hot-Laid Bituminou

11、sPaving Mixtures (Withdrawn 2009)3D3665 Practice for Random Sampling of Construction Ma-terialsD4215 Specification for Cold-Mixed, Cold-Laid BituminousPaving MixturesD4792 Test Method for Potential Expansion of Aggregatesfrom Hydration ReactionsD4867/D4867M Test Method for Effect of Moisture onAspha

12、lt Concrete Paving MixturesD5106 Specification for Steel Slag Aggregates for Bitumi-nous Paving MixturesD5711 Test Method for Determining the Adherent Coating1This specification is under the jurisdiction of ASTM Committee D04 on Roadand Paving Materials and is the direct responsibility of Subcommitt

13、ee D04.50 onAggregate Specifications.Current edition approved June 1, 2015. Published July 2015. Originally approvedin 1997. Last previous edition approved in 2013 as D6155 13. DOI: 10.1520/D6155-15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service

14、 at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshoh

15、ocken, PA 19428-2959. United States1on Coarse Aggregates (Withdrawn 2012)3D5821 Test Method for Determining the Percentage ofFractured Particles in Coarse AggregateE11 Specification for Woven Wire Test Sieve Cloth and TestSieves2.2 U. S. Environmental Protection Agency Standards:SW846 1311 EPA Test

16、Method, Toxicity CharacteristicLeaching Procedure43. Terminology3.1 DefinitionsFor defining aggregate types, see Descrip-tive Nomenclature C294 and Terminologies C125 and D8.4. Ordering Information4.1 Orders for the material under this specification shallinclude the following information:4.1.1 The s

17、pecification designation and year of issue,4.1.2 The size number as given in Classification D448 orgrading to be furnished,4.1.3 The quantity required,4.1.4 Use of the coarse aggregate, whether for conventionalmixtures or open-graded friction course mixtures (see 5.3 and5.4), and whether for surface

18、 courses or base courses,4.1.5 In case of sulfate soundness tests, which salt is to beused,4.1.6 Any angularity requirements, and4.1.7 Any special requirements.5. Physical Properties5.1 GeneralThe coarse aggregate shall consist of hard,strong, durable pieces, free of adherent coatings and conform-in

19、g to the requirements of this specification.5.2 GradingThe grading shall conform to one of thefollowing subparagraphs:5.2.1 The coarse aggregate grading shall conform to therequirements of Classification D448 for the size numberdesignated in the order. The size to be used is dependent uponthe desire

20、d composition of the paving mixture, and the requiredsize or sizes either before or after blending as specified.5.2.2 The coarse aggregate grading shall conform to thegrading as specified in the purchase order. The grading to beused is dependent upon the desired composition of the pavingmixture and

21、shall be determined by the purchaser.5.3 Fractured Particles in Coarse AggregateOrders formaterial under this specification shall state the appropriaterequirements for percentage of fractured particles.5.3.1 Conventional Mixtures, not less than 40 %, by mass,of the aggregate particles retained on th

22、e 4.75-mm (No. 4)sieve shall have at least one fractured face (see Note 2 and Note3).5.3.2 OpenGraded Friction Course Mixtures, of the aggre-gate particles retained on the 4.75-mm (No. 4) sieve, not lessthan 90 %, by mass, shall have one or more fractured faces andnot less than 75 %, by mass shall h

23、ave two or more fracturedfaces.NOTE 2Attention is called to the distinction between conventional(dense mixtures or open mixtures) and open-graded friction coursemixtures in Specification D3515.NOTE 3Some sources of aggregate contain angular particles that willperform similarly to a mechanically frac

24、tured particle. Where laboratorytests or service records indicate this to be true, such angular particles maybe considered as fractured.5.4 Polishing CharacteristicsThe coarse aggregates, orthe coarsest fraction of the aggregate for use in surface coursemixtures, shall be of a type known to possess

25、adequateresistance to polishing action of the anticipated traffic (see Note4).NOTE 4No ASTM test method has been recognized to be capable ofdefining adequate resistance to the polishing action of specific trafficconditions. Test Method D3319 has been found useful in evaluating therelative polish res

26、istance between samples of different aggregates ormixtures containing different aggregates.5.5 SoundnessThe coarse aggregate, when subjected tofive cycles of the soundness test, shall have a weighted loss notgreater than 12 % when sodium sulfate is used or 18 % whenmagnesium sulfate is used (see Not

27、e 5). If the salt is notdesignated by the purchaser, the aggregate shall be consideredto be in compliance with this specification if it meets theindicated limit for either salt used.5.6 DegradationAggregate subjected to testing in accor-dance with Test Method C131 shall have a loss not greater than4

28、0 % for surface courses or 50 % for base courses (see Note 5).NOTE 5Coarse aggregate failing to meet the requirements of 5.5 or5.6 may be considered for use provided that (1) similar aggregates fromthe same source have been shown by experience, to the satisfaction of thepurchaser, to result in satis

29、factory pavement and (2) the results of othertests indicate that the desired performance can be obtained. Aggregatefrom a new source that fails the requirements of 5.5 or 5.6 and for whichno experience exists, may be considered acceptable provided the results ofthe other relevant laboratory tests in

30、dicate that the desired performancecan be obtained.5.7 ExpansionAggregates that contain components sub-ject to hydration shall be obtained from sources approved bythe purchaser on the basis of either satisfactory performancerecord, aging, or other treatment known to reduce potentialexpansion to a sa

31、tisfactory level (see Note 6).NOTE 6Test Method D4792 has been used to evaluate the potential forexpansion of dense graded materials.5.8 Environmental StabilityAggregates shall be evaluatedfor environmental considerations (air quality, water quality,and storage) using the required local, state, and

32、federal testmethods in effect at the time of use.5.8.1 Aggregates that exhibit a potential for producingleachates shall be tested using the Toxicity CharacteristicLeaching Procedure (EPAMethod SW846 1311) or appropriatetest method as approved by the purchaser. Results shallindicate that all areas te

33、sted (metals, volatiles, semivolatiles,and organics) are below regulatory limits.5.8.2 The aggregate shall meet all applicable local, state,and federal environmental requirements in effect at the time ofuse.4Available from Department of Commerce, National Technical InformationCenter, 5285 Port Royal

34、 Road, Springfield, VA 22151. Order Number: EPASW-846.3.3.D6155 1525.9 Special RequirementsEvaluation will be required, butnot exclusive of, the following items, when specified by thepurchaser: the potential for stripping, friable particles.6. Methods of Sampling and Testing6.1 Sample the aggregates

35、 and determine the propertiesenumerated in this specification in accordance with the follow-ing methods:6.1.1 Random SamplingPractice D3665.6.1.2 SamplingPractice D75.6.1.3 GradingTest Method C136.6.1.4 Unit WeightTest Method C29/C29M.6.1.5 SoundnessTest Method C88.6.1.6 DegradationTest Method C131.

36、6.1.7 ExpansionTest Method D4792.6.1.8 Friable ParticlesTest Method C142.6.1.9 CoatingTest Method D2489.6.1.10 Adherent CoatingsTest Method D5711.6.1.11 Fractured ParticlesTest Method D5821.6.1.12 LeachingEPA Test Method SW846 1311.6.1.13 StrippingTest Method D4867/D4867M.7. Keywords7.1 bituminous p

37、aving; coarse aggregate; nontraditional ag-gregate; paving mixtures; recycled aggregateASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of

38、the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Y

39、our comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your commen

40、ts have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or mu

41、ltiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 153