ASTM D6053-2008 952 Standard Test Method for Determination of Volatile Organic Compound (VOC) Content of Electrical Insulating Varnishes《电绝缘漆中挥发性有机化合物(VOC)含量测定的标准试验方法》.pdf

《ASTM D6053-2008 952 Standard Test Method for Determination of Volatile Organic Compound (VOC) Content of Electrical Insulating Varnishes《电绝缘漆中挥发性有机化合物(VOC)含量测定的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM D6053-2008 952 Standard Test Method for Determination of Volatile Organic Compound (VOC) Content of Electrical Insulating Varnishes《电绝缘漆中挥发性有机化合物(VOC)含量测定的标准试验方法》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 6053 08An American National StandardStandard Test Method forDetermination of Volatile Organic Compound (VOC) Contentof Electrical Insulating Varnishes1This standard is issued under the fixed designation D 6053; the number immediately following the designation indicates the year oforig

2、inal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This test method covers the determination of the amountof vola

3、tile organic compounds emitted during cure of electricalinsulating varnishes.1.2 The values stated in SI units are to be regarded asstandard. The values given in parentheses are mathematicalconversions to inch-pound units that are provided for informa-tion only and are not considered standard.1.3 Th

4、is standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. See Section 7 forspe

5、cific precautions.2. Referenced Documents2.1 ASTM Standards:2D115 Test Methods for Testing Solvent Containing Var-nishes Used for Electrical InsulationD 1711 Terminology Relating to Electrical InsulationD 3960 Practice for Determining Volatile Organic Com-pound (VOC) Content of Paints and Related Co

6、atingsD 4733 Test Methods for Solventless Electrical InsulatingVarnishesD 5423 Specification for Forced-Convection LaboratoryOvens for Evaluation of Electrical InsulationE 691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method3. Terminology3.1 Definition of T

7、erm Specific to This Standard:3.1.1 varnish, electrical insulating, n a liquid resin sys-tem that is applied to and cured on electrical componentsproviding electrical, mechanical, and environmental protec-tion.3.1.1.1 DiscussionThere are two types of electrical insu-lating varnish: solvent-containin

8、g and solventless. The solvent-containing varnish is a solution, dispersion, or emulsion of apolymer or mixture of polymers in a volatile, nonreactableliquid. The solventless type is a liquid resin system free ofvolatile, nonreactable solvents.3.1.2 For definitions of other terms pertaining to this

9、testmethod, refer to Terminology D 1711.4. Significance and Use4.1 This test method determines the volatile organic contentof an electrical insulating varnish. It utilizes a procedure wheredishes containing a known amount of varnish are baked and theamount of volatile organic compound is measured. C

10、alcula-tions are performed to express this in g/L or lb/gal. This testmethod is applicable to all types of varnishes. However,waterborne varnishes while baked under the same conditionsneed to have water content determined and calculations per-formed in accordance with Practice D 3960.4.1.1 During th

11、e cure of electrical insulating varnishes someorganic material is volatilized. A determination of the amountthat is volatilized is useful for estimating the amount of curedvarnish on electrical units and volatile organic emissions froma manufacturing facility.5. Interferences5.1 The amount of volati

12、le organic content determined bythis test method is known to be affected by the rate of airexchange in the baking oven.6. Apparatus6.1 Weighing Dishes, aluminum, approximately 60 mm (238in.) in diameter and 15 mm (58 in.) high on the sides.6.2 Forced-Convection Oven, see Specification D 5423-Type II

13、.6.3 Desiccator.1This standard is under the jurisdiction of ASTM Committee D09 on Electricaland Electronic Insulating Materials and is the direct responsibility of SubcommitteeD09.01 on Electrical Insulating Varnishes, Powders and Encapsulating Compounds.Current edition approved May 1, 2008. Publish

14、ed June 2008. Originallyapproved in 1996. Last previous edition approved in 2003 as D 6053 - 03.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Docume

15、nt Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.7. Hazards7.1 WarningDo not use varnish at temperatures abovethe flash point when in

16、adequate ventilation, and the possibilityof flames or sparks exist. Store varnish in sealed containers.8. Procedure8.1 Weigh three aluminum dishes to the nearest 0.01 g.8.2 Add approximately 2 to 10 g of the varnish to be testedto each dish.8.3 Weigh each dish and varnish to the nearest 0.01 g.8.4 R

17、oll the resin around in the dishes to ensure an evencoating.8.5 Place the dishes in a forced-convection oven at 150 6 2C. Other temperatures are permitted to be used when agreed toby interested parties.8.6 After 61 6 1 min remove the dishes from the oven.8.7 Cool in desiccator.8.8 Weigh each dish to

18、 the nearest 0.01 g.8.9 Calculate the volatile organic compound (VOC) contentfor each dish as follows except for waterborne varnishes. Forwaterborne varnishes determine the water content and performthe VOC calculations in accordance with Practice D 3960.Weight of Liquid Varnish, (1)A 5 Weight of dis

19、h and varnish before baking!2Weight of dishWeight of Baked Varnish,B 5 Weight of dish and varnish after baking!2Weight of dishWeight of VOC, C 5 A 2 BVolume of Liquid Varnish, V 5ADwhere:D = the density of the varnish in g/L as determined by TestMethods D 115 or D 4733.VOC 5CVexpressed in g/L (2)8.1

20、0 To convert VOC in g/L to lb/gal multiply the VOC ing/L by 0.00833.8.11 Calculate the average VOC of the three dishes.9. Report9.1 Report the following information:9.1.1 Identity of the varnish used,9.1.2 Average VOC in g/L or lb/gal,9.1.3 Temperature that dishes were baked, and9.1.4 Approximate ma

21、ss of resin tested.10. Precision and Bias10.1 PrecisionTable 1 lists the results based on a roundrobin test conducted in accordance with Practice E 691 involv-ing five laboratories and three materials at three differentweights. Each test result was the average of three specimens.Each laboratory obta

22、ined three test results for each material ateach weight.10.2 BiasThis test method has no bias because the valuefor VOC is determined solely in terms of this test method.11. Keywords11.1 electrical insulating varnish; VOC; volatile organiccompoundD6053082SUMMARY OF CHANGESCommittee D09 has identified

23、 the location of selected changes to this test method since the last issue,D 6053 03, that may impact the use of this test method. (Approved May 1, 2008)(1) Revised 8.5 to replace non-mandatory language.ASTM International takes no position respecting the validity of any patent rights asserted in con

24、nection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the respon

25、sible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful

26、consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 1

27、00 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM

28、website(www.astm.org).TABLE 1 Results in Grams/Litre (g/l)Materials SampleSizeAverage StandardDeviationRepeatabilityStandardDeviationReproducibilityStandardDeviationRepeatabilityLimitReproducibilityLimitUnsaturatedPolyester instyrene2 grams 226.8 30.44 5.08 28.18 14.22 78.906 grams 169.8 14.22 2.66

29、13.21 7.45 36.9910 grams 151.3 13.51 3.83 12.82 10.72 35.90UnsaturatedPolyester invinyl toluene2 grams 282.1 29.02 3.68 26.71 10.30 74.796 grams 211.0 5.32 6.89 7.95 19.29 22.2610 grams 192.5 7.26 4.93 8.01 13.80 22.43UnsaturatedPolyester inDAP2 grams 349.3 38.92 8.02 36.01 22.46 100.86 grams 288.7 12.48 6.50 12.84 18.20 35.9510 grams 268.2 10.59 9.00 12.69 25.20 35.53D6053083