ASTM D5702-2018 red 9375 Standard Practice for Field Sampling of Coating Films for Analysis for Heavy Metals.pdf
《ASTM D5702-2018 red 9375 Standard Practice for Field Sampling of Coating Films for Analysis for Heavy Metals.pdf》由会员分享,可在线阅读,更多相关《ASTM D5702-2018 red 9375 Standard Practice for Field Sampling of Coating Films for Analysis for Heavy Metals.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D5702 07 (Reapproved 2012)D5702 18Standard Practice forField Sampling of Coating Films for Analysis for HeavyMetals1This standard is issued under the fixed designation D5702; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revis
2、ion, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers a method to control the removal of samples of coating films from substrates for
3、subsequent laboratoryanalysis for heavy metal content on a mass basis. This technique can be used in the field, the fabricating shop, or laboratory.1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.1.3 This standard does not purp
4、ort to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine theapplicability of regulatory limitations prior to use. For specific hazar
5、d information, see Section 5, Note 1,and Note 3.1.4 This international standard was developed in accordance with internationally recognized principles on standardizationestablished in the Decision on Principles for the Development of International Standards, Guides and Recommendations issuedby the W
6、orld Trade Organization Technical Barriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D4138 Practices for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive, Cross-SectioningMeansD6132 Test Method for Nondestructive Measurement of Dry Film Thickne
7、ss of Applied Organic Coatings Using an UltrasonicCoating Thickness GageD7091 Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metalsand Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals3. Significance and Use3.1 Prior to beginn
8、ing a project that involves the removal, cutting, grinding, or burning of paint, it is necessary to determineif the coating contains hazardous materials,metals, such as lead, as lead. If it does, certain requirements for worker andenvironmental protection may need to be imposed. The presence and qua
9、ntity of hazardous materialsmetals in a paint can bedetermined through laboratory analysis; however, since the analysis is based on the weight of the specimen, the removal of thesample must be properly controlled to improve the reliability of the test results. analysis. Proper sampling protocol is n
10、eeded toassure the laboratory results represent the actual amount of heavy metal in the coating. The number and location of samples to beremoved must also be determined to characterize properly the extent of the presence of hazardous materials, if any, on a structure.4. Materials and Equipment4.1 Sa
11、mple Collection ContainerA clean plastic bag or rigid container comprised of a material such as polyethylene that willnot contaminate the sample.4.2 Straight Edge or Ruler.4.3 Knife or Chisel, cleaned and sharpened, for removing paint samples.4.4 Dry Film Thickness Gage, for measuring total coating
12、thickness.1 This practice is under the jurisdiction of ASTM Committee D01 on Paint and Related Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.46 on Industrial Protective Coatings.Current edition approved Nov. 1, 2012June 1, 2018. Published November 2012June
13、 2018. Originally approved in 1995. Last previous edition approved in 20072012 asD5702 07.D5702 07 (2012). DOI: 10.1520/D5702-07R12.10.1520/D5702-18.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standa
14、rdsvolume information, refer to the standardsstandards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically p
15、ossible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700,
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD57022018RED9375STANDARDPRACTICEFORFIELDSAMPLINGOFCOATINGFILMSFORANALYSISFORHEAVYMETALSPDF

链接地址:http://www.mydoc123.com/p-520453.html