ASTM D5364-2008 Standard Guide for Design Fabrication and Erection of Fiberglass Reinforced Plastic Chimney Liners with Coal-Fired Units.pdf

《ASTM D5364-2008 Standard Guide for Design Fabrication and Erection of Fiberglass Reinforced Plastic Chimney Liners with Coal-Fired Units.pdf》由会员分享，可在线阅读，更多相关《ASTM D5364-2008 Standard Guide for Design Fabrication and Erection of Fiberglass Reinforced Plastic Chimney Liners with Coal-Fired Units.pdf（25页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 5364 08An American National StandardStandard Guide forDesign, Fabrication, and Erection of Fiberglass Reinforced(FRP) Plastic Chimney Liners with Coal-Fired Units1This standard is issued under the fixed designation D 5364; the number immediately following the designation indicates the

2、 year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.INTRODUCTIONFederal and state environmental regulations have im

3、posed strict requirements to clean the gasesleaving a chimney. These regulations have resulted in taller chimneys (6001000 ft (183305 m) andlower gas temperatures (120200F (4993C) due to the use of Air Quality Compliance Systems(ACQS). These regulations led to the development of fiber reinforced pla

4、stics (FRP) chimney linersin the 1970s.Fiberglass-reinforced plastic liners have proven their capability to resist corrosion and carry loadsover long periods of time. Successful service has been demonstrated in the utility and general-processindustries for over 40 years. The taller FRPstructures and

5、 larger diameters (1030 ft (39 m) imposednew design, fabrication, and erection challenges.The design, fabrication, and erection of FRP liners involves disciplines which must address thespecific characteristics of the material. Areas that have been shown to be of importance include thefollowing:(1) F

6、lue-gas characteristics such as chemical composition, water and acid dew points, operating andexcursion temperature, velocity, etc.(2) Plant operation as it relates to variations in the flue-gas characteristics.(3) Material selection and laminate design.(4) Quality control throughout the design, fab

7、rication, and erection process to ensure the integrityof the corrosion barrier and the structural laminate.(5) Secondary bonding of attachments, appurtenances, and joints.(6) Installation and handling.(7) Inspections and Confirmation Testing.Chimney components include an outer shell, one or more inn

8、er liners, breeching ductwork, andmiscellaneous platforms, elevators, ladders, and miscellaneous components. The shell providesstructural integrity to environmental forces such as wind, earthquake, ambient temperatures, andsupports the liner or liners. The liner or liners inside the shell protects t

9、he shell from the thermal,chemical, and abrasive environment of the hot boiler gases (generally 120560F (49293C). Theseliners have been made of FRP, acid-resistant brick, carbon steel, stainless steel, high-alloy steel,shotcrete-coated steel, and shotcrete-coated shells. The selection of the materia

10、l type depends on thechemical composition and temperature of the flue gas, liner height, diameter, and seismic zone. Also,variations in flue-gas characteristics and durations of transient temperatures affect material selectionand design. For FRP liners, the flue gas maximum operating temperature is

11、generally limited to 200F(90C) for 2 hours and for maximum transient temperatures to 400F (204C) for 30 minutes.1. Scope1.1 This guide offers direction and guidance to the userconcerning available techniques and methods for design, ma-terial selection, fabrication, erection, inspection, confirmatory

12、testing, quality control and assurance.1This guide is under the jurisdiction of ASTM Committee D20 on Plastics andis the direct responsibility of Subcommittee D20.23 on Reinforced Plastic PipingSystems and Chemical Equipment.Current edition approved Nov. 1, 2008. Published November 2008. Originallya

13、pproved in 1993. Last previous edition approved in 2002 as D 5364 93 (2002).1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.1.2 These minimum guidelines, when properly used andimplemented, can help ensure a safe and reliable structur

14、e forthe industry.1.3 This guide offers minimum requirements for the properdesign of a FRP liner once the service conditions relative tothermal, chemical, and erosive environments are defined. Dueto the variability in liner height, diameter, and the environment,each liner must be designed and detail

15、ed individually.1.4 Selection of the necessary resins and reinforcements,composition of the laminate, and proper testing methods areoffered.1.5 Once the material is selected and the liner designed,procedures for proper fabrication of the liner are developed.1.6 Field erection, sequence of constructi

16、on, proper field-joint preparation, and alignment are reviewed.1.7 Quality control and assurance procedures are developedfor the design, fabrication, and erection phases. The quality-assurance program defines the proper authority and responsi-bility, control of design, material, fabrication and erec

17、tion,inspection procedures, tolerances, and conformity to standards.The quality-control procedures provide the steps required toimplement the quality-assurance program.1.8 Appendix X1 includes research and development sub-jects to further support recommendations of this guide.1.9 DisclaimerThe reade

18、r is cautioned that independentprofessional judgment must be exercised when data or recom-mendations set forth in this guide are applied. The publicationof the material contained herein is not intended as a represen-tation or warranty on the part ofASTM that this information issuitable for general o

19、r particular use, or freedom from infringe-ment of any patent or patents. Anyone making use of thisinformation assumes all liability arising from such use. Thedesign of structures is within the scope of expertise of alicensed architect, structural engineer, or other licensed profes-sional for the ap

20、plication of principles to a particular structure.NOTE 1There is no known ISO equivalent to this standard.1.10 The values stated in inch-pound units are to be re-garded as standard. The values given in parentheses aremathematical conversions to SI units that are provided forinformation only and are

21、not considered standard.1.11 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations pri

22、or to use.SectionIntroduction and BackgroundScope and Objective 1Referenced Documents 2ASTM Standards 2.1 2.1ACI Standard 2.2NFPA Standard 2.3ASME Standards 2.4Terminology 3ASTM Standard General Definitions 3.1Applicable Definitions 3.2Descriptions of Terms Specific to This Standard 3.3Symbols 3.4Si

23、gnificance and Use 4Service and Operating Environments 5Service Conditions 5.1Environmental Severity 5.2Chemical Environment 5.3Erosion/Abrasion Environment 5.4Operating Temperature Environment 5.5Abnormal Environments 5.6Other Operating and Service Environments 5.7Static Electricity Build-Up 5.8Fla

24、me Spread 5.9Materials 6Raw Materials 6.1Laminate Composition 6.2Laminate Properties 6.3Design 7Design 7.1Assumptions 7.2Dead Loads 7.3Wind Loads 7.4Earthquake Loads 7.5Thermal Loads 7.6Circumferential Pressure Loads 7.7Load Factors 7.8Resistance Factors 7.9Loading Combinations 7.10Allowable Longitu

25、dinal Stresses 7.11Allowable Circumferential Stresses 7.12Design Limits 7.13Tolerances 7.14Deflections 7.15Critical Deign Considerations and Details 7.16Fabrication 8Fabrication 8.1Reponsibility of Fabricator 8.2Fabrication Facility 8.3General Construction 8.4Fabrication Equipment 8.5Resin Systems 8

26、.6Reinforcement 8.7Fabrication Procedures 8.8Handling and Transportation 8.9Erection Appurtenances 8.10Tolerances 8.11Erection of FRP Liners 9Erection Scheme and Sequence 9.1Handling and Storage on Site 9.2Erection Appurtenances 9.3Field Joints 9.4Field Joints Lamination Procedure 9.5Quality Assuran

27、ce and Quality Control 10Quality Assurance and Quality Control 10.1Quality-Assurance Program 10.2Quality-Assurance Surveillance 10.3Inspections 10.4Submittals 10.5Operation Maintenance and Start-Up Procedures 11Initial Start-Up 11.1Operation and Maintenance 11.2AnnexTypical Inspection Checklist Anne

28、x A1AppendixCommentary Appendix X1References2. Referenced Documents2.1 ASTM Standards:2C 177 Test Method for Steady-State Heat Flux Measure-ments and Thermal Transmission Properties by Means ofthe Guarded-Hot-Plate ApparatusC 518 Test Method for Steady-State Thermal TransmissionProperties by Means o

29、f the Heat Flow Meter Apparatus2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.D5364082C 581 Practice for Det

30、ermining Chemical Resistance ofThermosetting Resins Used in Glass-Fiber-ReinforcedStructures Intended for Liquid ServiceC 582 Specification for Contact-Molded Reinforced Ther-mosetting Plastic (RTP) Laminates for Corrosion-ResistantEquipmentD 638 Test Method for Tensile Properties of PlasticsD 648 T

31、est Method for Deflection Temperature of PlasticsUnder Flexural Load in the Edgewise PositionD 695 Test Method for Compressive Properties of RigidPlasticsD 790 Test Methods for Flexural Properties of Unreinforcedand Reinforced Plastics and Electrical Insulating MaterialsD 883 Terminology Relating to

32、 PlasticsD 2393 Test Method for Viscosity of Epoxy Resins andRelated Components3D 2471 Practice for Gel Time and Peak Exothermic Tem-perature of Reacting Thermosetting Resins4D 2583 Test Method for Indentation Hardness of RigidPlastics by Means of a Barcol ImpressorD 2584 Test Method for Ignition Lo

33、ss of Cured ReinforcedResinsD 3299 Specification for Filament-Wound Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant TanksD 4398 Test Method for Determining the Chemical Resis-tance of Fiberglass-Reinforced Thermosetting Resins byOne-Side Panel ExposureE84 Test Method for Surface Burning C

34、haracteristics ofBuilding MaterialsE 228 Test Method for Linear Thermal Expansion of SolidMaterials With a Push-Rod Dilatometer2.2 American Concrete Institute (ACI) Standard:ACI Standard 307 Specification for the Design and Con-struction of Reinforced Concrete Chimneys52.3 NFPA Standard:NFPA 77 Reco

35、mmended Practice on Static Electricity62.4 ASME Standards:Section X Fiberglass Reinforced Plastic Pressure Vessels7RTP-1 Reinforced Thermoset Plastic Corrosion ResistantEquipment73. Terminology3.1 Definitions:3.1.1 Terms used in this guide are from Terminology D 883unless otherwise indicated in sect

36、ion 3.2.3.2 The following applicable definitions in this guide areprovided for reference:3.2.1 acceleratora material added to the resin to increasethe rate of polymerization (curing).3.2.2 axialin the direction of the axis (lengthwise center-line) of the equipment.3.2.3 Barcol hardnessmeasurement of

37、 the degree of cureby means of resin hardness. The Barcol impressor is theinstrument used (see Test Method D 2583).3.2.4 binderchemical treatment applied to the randomarrangement of glass fibers to give integrity to mats. Specificbinders are utilized to promote chemical compatibility withvarious lam

38、inating resins used.3.2.5 blisterrefer to Terminology D 883.3.2.6 bondingjoining of two or more parts by adhesiveforces.3.2.7 bond strengthforce per unit area (psi) necessary torupture a bond in interlaminar shear.3.2.8 bucklinga mode of failure characterized by anunstable lateral deflection due to

39、compressive action on thestructural element involved.3.2.9 burned areasareas of laminate showing evidence ofdecomposition (for example, discoloration and cracking) dueto excessive resin exotherm.3.2.10 burn out (burn off)thermal decomposition of theorganic materials (resin and binders) from a lamina

40、te specimenin order to determine the weight percent and laminationsequence of the glass reinforcement.3.2.11 catalystan organic peroxide material used to acti-vate the polymerization of the resin.3.2.12 chopped-strand matreinforcement made from ran-domly oriented glass strands that are held together

41、 in a matform by means of a binder.3.2.13 chopper guna machine used to cut continuousfiberglass roving to predetermined lengths usually 0.52 in.(1351 mm) and propel the cut strands to the mold surface. Inthe spray-up process, a catalyzed resin is deposited simulta-neously on the mold. When intersper

42、sed layers are provided infilament winding, the resin spray is not used.3.2.14 contact moldingprocess for molding reinforcedplastics in which reinforcement and resin are placed on an openmold or mandrel. Cure is without application of pressure;includes both hand-lay-up and spray-up.3.2.15 corrosion

43、barrierthe integral inner barrier of thelaminate which is made from resin, veil, and chopped mat.3.2.16 coveragesee winding cycle.3.2.17 crazingthe formation of tiny hairline cracks invarying degrees throughout the resin matrix, particularly inresin-rich areas.3.2.18 cut edgeend of a laminate result

44、ing from cuttingthat is not protected by a corrosion barrier.3.2.19 delaminationphysical separation or loss of bondbetween laminate plies.3.2.20 dry spotan area where the reinforcement fibershave not been sufficiently wetted with resin.3.2.21 edge sealingapplication of reinforcement andresin, or res

45、in alone, to seal cut edges and provide a corrosion-resistant barrier. The final layer should be paraffinated.3.2.22 entrapped-air voidsee void.3Withdrawn. The last approved version of this historical standard is referencedon www.astm.org4Withdrawn. The last approved version of this historical stand

46、ard is referencedon www.astm.org.5Available fromAmerican Concrete Institute (ACI), P.O. Box 9094, FarmingtonHills, MI 48333-9094, http:/www.concrete.org.6Available from National Fire Protection Association (NFPA), 1 BatterymarchPark, Quincy, MA 02169-7471, http:/www.nfpa.org.7Available from American

47、 Society of Mechanical Engineers (ASME), ASMEInternational Headquarters, Three Park Ave., New York, NY 10016-5990, http:/www.asme.org.D53640833.2.23 environmentstate of the surroundings in contactwith the internal and external surfaces, including the tempera-ture, pressure, chemical exposure, relati

48、ve humidity, and pres-ence of liquids or gases.3.2.24 exothermevolution of heat by the resin during thepolymerization reaction.3.2.25 exotherm plythat ply of chopped mat at which thelamination process is stopped to allow gelation and exothermof the existing laminate.3.2.26 fabricatorthe producer of

49、the equipment who com-bines resin and reinforcing fibers to produce the final product.3.2.27 fatiguethe change in properties of the laminateover time under cycling of loads, including mechanical,temperature, and other environmental exposures.3.2.28 fiber(glass)a fine, continuously formed thread ofglass. E-glass is used for strength and durability, E-CR-glass isa modified E-glass with improved corrosion resistance to mostacids, and C-glass is resistant to corrosion by most acids.3.2.29 fiberglass rovingsee roving.3.2.30 fiber