ASTM D4737-2009a Standard Test Method for Calculated Cetane Index by Four Variable Equation.pdf

《ASTM D4737-2009a Standard Test Method for Calculated Cetane Index by Four Variable Equation.pdf》由会员分享，可在线阅读，更多相关《ASTM D4737-2009a Standard Test Method for Calculated Cetane Index by Four Variable Equation.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D4737 09aStandard Test Method forCalculated Cetane Index by Four Variable Equation1This standard is issued under the fixed designation D4737; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A

2、 number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 The calculated Cetane Index by Four Variable Equationprovides a means for estimating the ASTM cetane number(Test Method D613) of dist

3、illate fuels from density anddistillation recovery temperature measurements. The valuecomputed from the equation is termed the Calculated CetaneIndex by Four Variable Equation.1.2 The Calculated Cetane Index by Four Variable Equationis not an optional method for expressingASTM cetane number.It is a

4、supplementary tool for estimating cetane number whena result by Test Method D613 is not available and if cetaneimprover is not used. As a supplementary tool, the CalculatedCetane Index by Four Variable equation must be used with dueregard for its limitations.1.3 Procedure A is to be used for Specifi

5、cation D975,Grades No. 1D S15, No. 1D S500, No. 1D S5000, No. 2DS5000, and No. 4D. This method for estimating cetanenumber was developed by Chevron Research Co.2ProcedureAis based on a data set including a relatively small number ofNo. 1D fuels. Test Method D4737 Procedure A may be lessapplicable to

6、 No.1D S15, No. 1D S500, and No. 1 D S5000than to No. 2D grade S5000 or to No. 4D fuels.1.4 Procedure B is to be used for Specification D975,Grades No. 2D S15 and No. 2D S500.1.5 The test method “Calculated Cetane Index by FourVariable Equation” is particularly applicable to Grade 1DS5000, Grade No.

7、 1D S500, Grade No. 2D S5000 and GradeNo. 2D S500 diesel fuel oils containing straight-run andcracked stocks, and their blends. It can also be used for heavierfuels with 90 % recovery points less than 382C and for fuelscontaining derivatives from oil sands and oil shale.NOTE 1Sxx is the designation

8、for maximum sulfur level specified forthe grade. For example, S500 grades are those with a maximum sulfurlimit of 500 ppm (g/g).1.6 Biodiesel blends are excluded from this test method,because they were not part of the datasets use to develop eitherProcedure A or B.1.7 The values stated in SI units a

9、re to be regarded asstandard. No other units of measurement are included in thisstandard.1.8 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practice

10、s and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:3D86 Test Method for Distillation of Petroleum Products atAtmospheric PressureD613 Test Method for Cetane Number of Diesel Fuel OilD975 Specification for Diesel Fuel OilsD1298 Test Met

11、hod for Density, Relative Density (SpecificGravity), or API Gravity of Crude Petroleum and LiquidPetroleum Products by Hydrometer MethodD2887 Test Method for Boiling Range Distribution ofPetroleum Fractions by Gas ChromatographyD4052 Test Method for Density, Relative Density, and APIGravity of Liqui

12、ds by Digital Density MeterD6751 Specification for Biodiesel Fuel Blend Stock (B100)for Middle Distillate FuelsD6890 Test Method for Determination of Ignition Delayand Derived Cetane Number (DCN) of Diesel Fuel Oils byCombustion in a Constant Volume ChamberD7170 Test Method for Determination of Deri

13、ved CetaneNumber (DCN) of Diesel Fuel OilsFixed Range Injec-tion Period, Constant Volume Combustion ChamberMethod2.2 CEN Standards:4EN 14214 Automotive fuels Fatty acid methyl esters1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products and Lubricants and is the direc

14、t responsibility of SubcommitteeD02.E0.02 on Diesel Fuel Oils.Current edition approved Dec. 1, 2009. Published December 2009. Originallyapproved in 1987. Last previous edition approved in 2009 as D473709. DOI:10.1520/D4737-09a.2Ingham, M. C., et al., “Improved Predictive Equations for Cetane Number,

15、”SAE Paper No 860250, Society of Automotive Engineers (SAE), 400 Common-wealth Dr., Warrendale, PA 15096-0001.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the st

16、andards Document Summary page onthe ASTM website.4Available from the National CEN members listed on the CEN website(www.cenorm.be) or from the CEN/TC 19 Secretariat (astmnen.nl).1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO

17、 Box C700, West Conshohocken, PA 19428-2959, United States.(FAME) for diesel engines Requirements and testmethods3. Summary of Test Method3.1 Two correlations in SI units have been establishedbetween the ASTM cetane number and the density and 10 %,50 %, and 90 % distillation recovery temperatures of

18、 the fuel.Procedure A has been developed for diesel fuels meeting therequirements of Specification D975 Grades No. 1D S15, No.1D S500, No. 1D S5000, No. 2D S5000, and No. 4D. Therelationship is given by the following equation:CCI 5 45.2 1 0.0892! T10N! 1 0.131 1 0.901!B!#T50N#1 0.05232 0.420!B!#T90N

19、# 1 0.00049T10N!22 T90N!2# 1 107!B!1 60!B!2(1)where:CCI = Calculated Cetane Index by Four Variable Equa-tion,D = Density at 15C, g/mL determined by Test Meth-ods D1298 or D4052,DN = D - 0.85,B =e(-3.5)(DN)-1,T10= 10 % recovery temperature, C, determined byTest Method D86 and corrected to standard ba

20、ro-metric pressure,T10N=T10- 215,T50= 50 % recovery temperature, C, determined byTest Method D86 and corrected to standard baro-metric pressure,T50N=T50- 260,T90= 90 % recovery temperature, C, determined byTest Method D86 and corrected to standard baro-metric pressure, andT90N=T90- 310.3.2 The empir

21、ical equation for Procedure A of the Calcu-lated Cetane Index by Four Variable Equation was derivedusing a generalized least squares fitting technique whichaccounted for measurement errors in the independent variables(fuel properties) as well as in the dependent variable (cetanenumber by Test Method

22、 D613). The data base consisted of1229 fuels including; commercial diesel fuels, refinery blend-ing components and fuels derived from oil sands, shale, andcoal. The analysis also accounted for bias amongst the indi-vidual sets of data comprising the database.3.3 Procedure B has been developed for di

23、esel fuels meetingthe requirements of Specification D975 Grade 2D S15 andNo. 2D S500. The relationship is given by the followingequation:CCI 52386.26D! 1 0.1740 T10! 1 0.1215 T50! 1 0.01850 T90!1 297.42 (2)where:CCI = Calculated Cetane Index by Four Variable EquationD = Density at 15C, g/mL determin

24、ed by Test MethodsD1298 or D4052T10= 10 % recovery temperature, C, determined by TestMethod D86 and corrected to standard barometricpressureT50= 50 % recovery temperature, C, determined by TestMethod D86 and corrected to standard barometricpressureT90= 90 % recovery temperature, C, determined by Tes

25、tMethod D86 and corrected to standard barometricpressure3.3.1 The equation for Procedure B when T10,T50, and T90are in F is:CCI 52386.26D! 1 0.09668 T10! 1 0.06751 T50! 1 0.01028 T90!1 291.83 (3)where:CCI = Calculated Cetane Index by Four Variable EquationD = Density at 15C, g/mL determined by Test

26、MethodD1298 or D4052T10= 10 % recovery temperature, F, determined by TestMethod D86 and corrected to standard barometricpressureT50= 50 % recovery temperature, F, determined by TestMethod D86 and corrected to standard barometricpressureT90= 90 % recovery temperature, F, determined by TestMethod D86

27、and corrected to standard barometricpressure3.4 The empirical equation for Procedure B of the Calcu-lated Cetane Index by Four Variable Equation was derivedfrom National Exchange Group data for 87 No. 2D S15 andNo. 2D S500 diesel fuels with sulfur level between 16 and500 ppm using a Partial Least Sq

28、uares technique. A 2-principalcomponent model was chosen. The model was validated witha set of 980 diesel fuels with sulfur levels in the same range.4. Significance and Use4.1 The Calculated Cetane Index by Four Variable Equationis useful for estimating ASTM cetane number when a testengine is not av

29、ailable for determining this property directlyand when cetane improver is not used. It may be convenientlyemployed for estimating cetane number when the quantity ofsample available is too small for an engine rating. In caseswhere the ASTM cetane number of a fuel has been previouslyestablished, the C

30、alculated Cetane Index by Four VariableEquation is useful as a cetane number check on subsequentbatches of that fuel, provided the fuels source and mode ofmanufacture remain unchanged.NOTE 2Test Methods D6890 and D7170 may be used to obtain aDerived Cetane Number (DCN) when the quantity of sample is

31、 too smallfor an engine test. These methods do measure the effect of cetaneimprover.4.2 Within the range from 32.5 to 56.5 cetane number, theexpected error of prediction of Procedure A of the CalculatedCetane Index by Four Variable Equation will be less than 62cetane numbers for 65 % of the distilla

32、te fuels evaluated.Errors may be greater for fuels whose properties fall outsidethe recommended range of application.5. Procedure5.1 Determine the density of the fuel at 15C to the nearest0.0001 g/mL, as described in Test Method D1298 or TestMethod D4052.D4737 09a25.2 Determine the 10 %, 50 %, and 9

33、0 % recovery tempera-tures of the fuel, as described in Test Method D86.5.3 Test Method D2887 maybe used as an alternative to TestMethod D86 to determine the 10%, 50%, 90% recoverytemperatures of the fuel.5.3.1 If Test Method D2887 is used, convert the TestMethod D2887 data to estimated Test Method

34、D86 datafollowing Appendix X5, Correlation of Jet and Diesel Fuel, ofTest Method D2887 and use the estimated Test Method D86data in place of actual Test Method D86 data in the calcula-tions.5.3.2 Provision for use of Test Method D2887 data in thistest method is intended to facilitate its use in dete

35、rminingcompliance with Specification D975 requirements. If this testmethod is used for purposes other than Specification D975compliance, the use of estimated Test Method D86 data shouldbe reviewed to ensure it is acceptable.6. Calculation or Interpretation of Results6.1 Compute the Calculated Cetane

36、 Index by Four VariableEquation using the equation given in 3.1 (Procedure A) forGrades 1D S15, 1D S500, 1D S5000, 2D S5000, and 4D.The calculation of Procedure A is more easily performed usinga computer or programmable hand calculator. Round the valueobtained to the nearest one-tenth. Compute the C

37、alculatedCetane Index by Four Variable Equation using the equationgiven in 3.3. (Procedure B) for Grade 2D S15 and 2D S500.6.1.1 Calculated Cetane Index by Four Variable Equation(Procedure A) can also be easily determined by means of thenomographs (applicable to Procedure A only) appearing inFigs. 1

38、-3. Fig. 1 is used to estimate the cetane number of a fuelbased on its density at 15C and its 50 % recovery temperature.Fig. 2 is used to determine a correction for the estimate fromFig. 1 to account for deviations in the density and the 90 %recovery temperature of the fuel from average values. Fig.

39、 3 isused to determine a second correction for the estimate fromFig. 1 to account for deviations in the 10 % and the 90 %FIG. 1 Calculated Cetane IndexFIG. 2 Calculated Cetane IndexFIG. 3 Calculated Cetane IndexD4737 09a3recovery temperatures of the fuel from average values. Thecorrections determine

40、d from Fig. 2 and Fig. 3 are summedalgebraically with the cetane number estimate from Fig. 1 tofind the Calculated Cetane Index by Four Variable Equation(Procedure A). The method of using these nomographs isindicated by the illustrative example shown below and on Figs.1-3.Measured Fuel PropertiesTes

41、t Method D613 Cetane Number 37.0Test Method D1298 Density at 15C, kg/L 0.885Test Method D86 10 % Recovery Temperature, C 234Test Method D86 50 % Recovery Temperature, C 274Test Method D86 90 % Recovery Temperature, C 323Calculated Cetane IndexEstimate from Fig. 1 34.0Correction from Fig. 2 +0.6Corre

42、ction from Fig. 3 +2.5_CCI = 37.16.2 The Calculated Cetane Index by Four Variable Equationpossesses certain inherent limitations which must be recog-nized in its application. These are as follows:6.2.1 It is not applicable to fuels containing additives forraising the cetane number.6.2.2 It is not ap

43、plicable to pure hydrocarbons, nor tonon-petroleum fuels derived from coal.6.2.3 It is not applicable to fuels containing biodiesel asdefined by Specification D6751 or CEN SpecificationEN 14214.6.2.4 Substantial inaccuracies in correlation may occur ifthe equation is applied to residual fuels or cru

44、de oils.7. Report7.1 Report the result of Procedure A or Procedure B to onedecimal place (XX.X) as:Cetane Index by D4737 Procedure A or B!5_(4)8. Precision and Bias8.1 The determination of Calculated Cetane Index by FourVariable Equation from measured density at 15C and mea-sured 10 %, 50 % and 90 %

45、 recovery temperatures is exact.8.2 PrecisionThe precision of the Calculated Cetane In-dex by Four Variable Equation is dependent on the precision ofthe original density and recovery temperature determinationswhich enter into the calculation. Test Method D1298 has astated repeatability limit of 0.00

46、06 kg/L and a stated reproduc-ibility limit of 0.0015 kg/L at 15C. Test Method D4052 has astated repeatability of 0.0001 g/mL and reproducibility of0.0005 g/mL. Test Method D86 has stated repeatability andreproducibility limits which vary with the rate of change ofrecovery temperature. See Figs. 2 t

47、hrough 7 and Tables 7through 10 of Test Method D86 for details.8.3 BiasNo general statement is made on bias of this testmethod since a comparison with accepted reference values isnot available.9. Keywords9.1 cetane; cetane index; diesel fuelSUMMARY OF CHANGESSubcommittee D02.E0.02 has identified the

48、 location of selected changes to this standard since the last issue(D473709) that may impact the use of this standard. (Approved Dec. 1, 2009.)(1) Added Test Methods D6890 and D7170 to the ReferencedDocuments and standard text.(2) Added new Note 2.(3) Added CEN Specification EN 14214 to the Referenc

49、edDocuments and standard text.Subcommittee D02.E0.02 has identified the location of selected changes to this standard since the last issue(D473704) that may impact the use of this standard. (Approved Oct. 1, 2009.)(1) Revised 1.3, 1.4, 1.5, 3.1, 3.3, 3.4, 5.2, and 6.1.(2) Added Note 1, 1.6, and 6.2.3.(3) Added Specification D6751 to the Referenced Documents.D4737 09a4ASTM International takes no position respecting the validity of any patent rights asserted in