ASTM D2680-2001(2014) Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer Piping《丙烯腈-丁二烯-苯乙烯共聚物 (ABS) 和聚氯.pdf
《ASTM D2680-2001(2014) Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer Piping《丙烯腈-丁二烯-苯乙烯共聚物 (ABS) 和聚氯.pdf》由会员分享,可在线阅读,更多相关《ASTM D2680-2001(2014) Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer Piping《丙烯腈-丁二烯-苯乙烯共聚物 (ABS) 和聚氯.pdf(8页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D2680 01 (Reapproved 2014) An American National StandardStandard Specification forAcrylonitrile-Butadiene-Styrene (ABS) and Poly(VinylChloride) (PVC) Composite Sewer Piping1This standard is issued under the fixed designation D2680; the number immediately following the designation indica
2、tes the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers thermoplastic comp
3、osite pipe,fittings and a joining system for use in gravity flow, nonpres-sure sanitary sewer, and storm drain installations. The pipe andfittings are made of ABS or PVC plastic material. Recom-mended installation practices are referenced in Appendix X1.1.2 The values stated in inch-pound units are
4、to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 The following safety hazards caveat pertains only to thetest method portion, Section 10, of this specification: Thisstandard do
5、es not purport to address all of the safety problems,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.Specific precautionary information is
6、 givenin 7.2.4.2. Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1084 Test Methods for Viscosity of AdhesivesD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)Compounds and Chlorinated Poly
7、(Vinyl Chloride)(CPVC) CompoundsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2152 Test Method for Adequacy of Fusion of ExtrudedPoly(Vinyl Chloride) (PVC) Pipe and Molded Fittings byAcetone ImmersionD2235 Specification for Solvent Cement for Acrylonitrile-Butadien
8、e-Styrene (ABS) Plastic Pipe and FittingsD2321 Practice for Underground Installation of Thermoplas-tic Pipe for Sewers and Other Gravity-Flow ApplicationsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2564 Specification for Solvent Ce
9、ments for Poly(VinylChloride) (PVC) Plastic Piping SystemsD3138 Specification for Solvent Cements for TransitionJoints Between Acrylonitrile-Butadiene-Styrene (ABS)and Poly(Vinyl Chloride) (PVC) Non-Pressure PipingComponentsD3212 Specification for Joints for Drain and Sewer PlasticPipes Using Flexib
10、le Elastomeric SealsD3965 Classification System and Basis for Specifications forRigid Acrylonitrile-Butadiene-Styrene (ABS) Materialsfor Pipe and FittingsD4396 Specification for Rigid Poly(Vinyl Chloride) (PVC)and Chlorinated Poly(Vinyl Chloride) (CPVC) Com-pounds for Plastic Pipe and Fittings Used
11、in NonpressureApplicationsF402 Practice for Safe Handling of Solvent Cements,Primers, and Cleaners Used for Joining ThermoplasticPipe and FittingsF412 Terminology Relating to Plastic Piping SystemsF477 Specification for Elastomeric Seals (Gaskets) for Join-ing Plastic PipeF913 Specification for Ther
12、moplastic Elastomeric Seals(Gaskets) for Joining Plastic Pipe2.2 Federal Standard:Fed. Std. No. 123 Marking for Shipment (Civil Agencies)32.3 Military Standard:MIL-STD-129 Marking for Shipment and Storage33. Terminology3.1 Definitions:3.1.1 GeneralDefinitions are in accordance with Termi-nology F412
13、 and abbreviations are in accordance with Termi-nology D1600, unless otherwise specified.The abbreviation for1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer.Current edition approved Aug. 1,
14、2014. Published November 2014. Originallypublished as D2680 68 T. Last previous edition approved in 2009 asD2680 01(2009). DOI: 10.1520/D2680-01R14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandar
15、ds volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/www.dodssp.daps.mil.Copyright ASTM International, 100 Barr Harbor Drive, PO Box
16、 C700, West Conshohocken, PA 19428-2959. United States1acrylonitrile-butadiene-styrene isABS and the abbreviation forpoly(vinyl chloride) is PVC.3.2 Definitions of Terms Specific to This Standard:3.2.1 acrylonitrile-butadiene-styrene (ABS)plastics con-taining polymers or blends of polymers, or both,
17、 in which theminimum butadiene content is 6 %; the minimum acrylonitrilecontent is 15 %; the minimum styrene or substituted styrenecontent, or both, is 15 %; and the maximum content of all othermonomers is not more than 5 %, plus lubricants, stabilizers,and colorants.3.2.2 poly (vinyl chloride) (PVC
18、)plastic compounds con-taining poly(vinyl chloride) homopolymer, and such additivesas stabilizers, lubricants, processing aids, impact improvers,and colorants as needed to provide the required processing andtoughness characteristics.4. Classification4.1 Pipe produced in accordance with this specific
19、ation shallbe classified as ABS composite pipe or PVC composite pipebased on plastic materials used in manufacture.5. Materials and Manufacture5.1 ABS composite pipe or PVC composite pipe shallconsist of two concentric thermoplastic tubes integrally bracedacross the annulus. The resultant annular sp
20、ace is filled toprovide continuous support between the inner and outer tubes.5.2 CompoundsThe ABS and PVC composite pipe andfittings shall be produced from the following compounds:5.2.1 ABSThe pipe shall be made from a rigidABS plasticand shall meet or exceed the requirements of SpecificationD3965 f
21、or a minimum cell classification of 1-0-2-2-3. Thefittings shall be made from ABS plastic and shall meet orexceed the requirements of Specification D3965 for cellclassifications of 1-0-2-2-3 or 4-2-2-2-2. Clean rework ABS,generated from the manufacturers own pipe extrusion andfittings may be used by
22、 the same manufacturer, provided thatthe pipe and fittings produced meet all the requirements of thisspecification.5.2.2 PVCThe thermoplastic material shall be a rigid PVCplastic and shall meet or exceed the requirements of Specifi-cation D1784, for a minimum cell classification of 12454 or ofSpecif
23、ication D4396, for a minimum cell classification of11432. Homopolymer PVC compounds that have higher cellclassifications, because one or more properties are superior tothose of the specified compounds, are also acceptable. Cleanrework PVC, generated from the manufacturers own pipe andfittings produc
24、tion may be used by the same manufacturerprovided that the pipe and fittings produced meet all therequirements of this specification.5.3 The other component shall be portland cement-perliteconcrete or other inert filler material exhibiting the samedegree of performance, that essentially fills the tr
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD268020012014STANDARDSPECIFICATIONFORACRYLONITRILEBUTADIENESTYRENEABSANDPOLYVINYLCHLORIDEPVCCOMPOSITESEWERPIPING

链接地址:http://www.mydoc123.com/p-517690.html