ASTM D4113-2002(2013) Standard Performance Specification for Woven Slipcover Fabrics《机织家具套织物的标准性能规格》.pdf

《ASTM D4113-2002(2013) Standard Performance Specification for Woven Slipcover Fabrics《机织家具套织物的标准性能规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM D4113-2002(2013) Standard Performance Specification for Woven Slipcover Fabrics《机织家具套织物的标准性能规格》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D4113 02 (Reapproved 2013)Standard Performance Specification forWoven Slipcover Fabrics1This standard is issued under the fixed designation D4113; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revisi

2、on. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This performance specification covers woven fabricscomprised of any textile fiber or mixture of fibers to be used inslipcovers.1.

3、2 These requirements apply to both the length and widthdirections for those properties where fabric direction is perti-nent.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appr

4、o-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD434 Test Method for Resistance to Slippage of Yarns inWoven Fabrics Using a Standard Seam (Withdrawn2003)3D133

5、6 Test Method for Distortion of Yarn in Woven FabricsD2261 Test Method for Tearing Strength of Fabrics by theTongue (Single Rip) Procedure (Constant-Rate-of-Extension Tensile Testing Machine)D2724 Test Methods for Bonded, Fused, and LaminatedApparel FabricsD5034 Test Method for Breaking Strength and

6、 Elongation ofTextile Fabrics (Grab Test)2.2 AATCC Test Methods:48 Colorfastness to Crocking: AATCC Crockmeter Method15 Colorfastness to Perspiration16 Colorfastness to Light23 Colorfastness to Burnt Gas Fumes61 Colorfastness to Laundering, Home and Commercial:Accelerated116 Colorfastness to Crockin

7、g: Rotary Vertical CrockmeterMethod124 Appearance of Fabrics After Repeated Home Launder-ings129 Colorfastness to Ozone in the Atmosphere Under HighHumidities132 Colorfastness to Drycleaning135 Dimensional Changes in Automatic Home Launderingof Woven or Knit Fabrics187 Dimensional Changes of Fabrics

8、: AcceleratedEvaluation Procedure No. 1 Gray Scale for Color ChangeEvaluation Procedure No. 2 Gray Scale for StainingEvaluation Procedure No. 8 AATCC 9Step ChromaticTransference Scale2.3 Other Document:5UFAC Fabric Classification Test Method for Cigarette Smol-der Resistance2.4 Military Standard6ASQ

9、/ANSI Z1.4 Sampling Procedures and Tables for In-spection by AttributesNOTE 1Reference to test methods in this performance specificationgive only the permanent part of the designation of ASTM, AATCC, orother test methods. The current editions of each test method cited shallprevail.3. Terminology3.1

10、Definitions:3.1.1 For definitions of textile terms used in this perfor-mance specification, refer to Terminology D123 and theTechnical Manual of the American Association of TextileChemists and Colorists.3.2 Definitions found in a dictionary of common terms aresuitable for use in this performance spe

11、cification.4. Specification Requirements4.1 The properties of woven fabrics for use in slipcoversshall conform to the specification requirements in Table 1.1This performance specification is under the jurisdiction of ASTM CommitteeD13 on Textiles and is the direct responsibility of Subcommittee D13.

12、63 on HomeFurnishings.Current edition approved Oct. 1, 2013. Published October 2013. Originallyapproved in 1982. Last previous edition approved in 2008 as D4113 02(2008).DOI: 10.1520/D4113-02R13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at

13、serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from American Association of Textile Chemists and Colorists(AATCC), P.O

14、. Box 12215, Research Triangle Park, NC 27709, http:/www.aatcc.org.5Available from UFAC Central, Box 2436, High Point, NC 27261.6Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.Copyright ASTM International, 100 Barr Ha

15、rbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15. Significance and Use5.1 Fabrics intended for this end-use should meet all of therequirements listed inTable 1 .5.2 It should be recognized that fabrics can be producedwith an almost infinite number of combination of construc

16、tionvariables (for example, type of fibers, percentage of fibers, yarntwist, yarn number, warp and pick count, chemical andmechanical finishes). Additionally, fashion or aesthetics dictatethat the ultimate consumer may find acceptable articles madefrom fabrics that do not conform to all of the requi

17、rements inTable 1.5.2.1 Hence, no single performance specification can possi-bly apply to all the various fabrics that could be utilized for thisend-use.5.3 The uses and significance of particular properties andtest methods are discussed in the appropriate sections of thespecified test methods.6. Te

18、st Methods (see Note 1)6.1 Breaking Force Determine the dry breaking force, inthe standard atmosphere for testing textiles, as directed in TestMethod D5034, using a constant rate of extension (CRE)tensile-testing machine.6.2 Resistance to Yarn SlippageDetermine the resistanceto yarn slippage as dire

19、cted in Test Method D434.NOTE 2The precision of Method D434 is being established, and itmay not be suitable for fabrics with low-yarn counts in terms of ends andpicks per inch (see 5.2).6.3 Tongue-Tear StrengthDetermine the tongue-tearstrength as directed in Test Method D2261.6.4 Yarn Distortion Det

20、ermine the yarn distortion asdirected in Test Method D1336.6.5 Dimensional Change:6.5.1 LaunderingDetermine the maximum dimensionalchange after five launderings as directed in the applicableprocedure in AATCC Test Method 135 or as agreed uponbetween the purchaser and the supplier (Note 3).6.5.1.1 Th

21、e wash conditions and drying procedure shall beas specified by the supplier.6.5.2 Drycleaning Determine the maximum-dimensionalchange after three dry cleanings as directed in 10.1.1 through10.1.5 of Test Methods D2724 or as agreed upon between thepurchaser and the supplier (Note 3).NOTE 3Launderable

22、 fabrics are expected to be dry-cleanable exceptwhere all or part of the fabric is not dry-cleanable and is so labeled. Forexample, the fabric could contain a functional finish that is soluble in thesolvent, or the fiber could be degraded by the solvent, as would be the casewith poly(vinyl chloride)

23、 fiber. “Dry-cleanable” goods are to be dry-cleaned only.6.6 Colorfastness:6.6.1 Burnt Gas Fumes Determine the colorfastness toburnt gas fumes on the original fabric and after one launderingor one dry cleaning as directed inAATCC Test Method 23 after1 cycle.NOTE 4Washing conditions shall be the same

24、 as those used in 6.5.1.1.Dry-cleaning conditions shall be the same as those used in 6.5.2.6.6.2 LaunderingDetermine the colorfastness to launder-ing as directed in the applicable procedure of AATCC TestMethod 61. The test conditions shall be as specified by thesupplier (Note 3).6.6.3 Dry cleaningDe

25、termine colorfastness to dry clean-ing as directed in AATCC Test Method 132 (Note 3).6.6.4 CrockingDetermine colorfastness to dry and wetcrocking as directed in AATCC Test Method 8 for solid shadesand AATCC Test Method 116 for prints.6.6.5 Perspiration Determine colorfastness to perspira-tion as dir

26、ected in AATCC Test Method 15.6.6.6 LightDetermine colorfastness to light as directed inAATCC Test Method 16.NOTE 5There are distinct differences in spectral distribution betweenthe various types of machines listed in AATCC Test Method 16, with nooverall correlations between them. Consequently, thes

27、e machines cannotbe used interchangeably. In case of controversy, results obtained with theWater-Cooled Xenon-Arc machine listed in Option E shall prevail.6.6.7 OzoneDetermine the colorfastness to ozone aftertwo cycles as directed in AATCC Test Method 129.TABLE 1 Specification RequirementsNOTE 1Clas

28、s for color change, color transfer, and DP rating is basedon a numerical scale of 5 for negligible or no color change, color transfer,or wrinkle to 1 for severe color change, color transfer, or wrinkle.Characteristic Requirements SectionBreaking strength (load)(CRT) 220 N (50 lbf)min6.1Yarn slippage

29、 6-mm (14-in.) sepa-ration at 67 N(15 lbf), min6.2Tongue-tear strength 13N(3.0lbf)min 6.3Yarn distortion 2.5 mm (0.10 in),max at 9-N (2-lbf) load6.4Dimensional change:LaunderingDry cleaning2.5 %, max2.5 %, max6.5.16.5.2Colorfastness:Burnt gas fumes1 cycle: 6.6.1Shade change after one Grade 4A,minlau

30、ndering or onedry cleaningLaundering: 6.6.2Shade changeStainingGrade 4A,minGrade 3B,minDry cleaning: 6.6.3Shade change Grade 4A,minCrocking: 6.6.4DryWetGrade 4C,minGrade 3C,minPerspiration: 6.6.5Shade changeStainingGrade 4A,minGrade 3B,minLight (40 AATCC FU)(xenon-arc)Step 4A,min 6.6.6Ozone Grade 4,

31、 min 6.6.7Fabric appearance (see 6.7.1.1)SA3.5D,min 6.7Flammability: pass 6.8AAATCC Gray Scale for Color Change.BAATCC Gray Scale for Staining.CAATCC Chromatic Transference Scale.DFor durable press fabrics only.D4113 02 (2013)26.7 Fabric AppearanceDetermine the fabric appearanceas directed in AATCC

32、Test Method 124 after laundering usingthe wash-and-wear cycle or the normal cycle as agreed uponbetween the purchaser and the supplier as specified in 6.5.1.1for washable fabrics or after dry cleaning as specified in 6.5.2for dry-cleanable fabrics (see Note 3).6.7.1 For fabrics not intended for use

33、in durable pressdetermine the fabric smoothness after pressing as specified in10.2.3 of Test Methods D2724.6.7.1.1 The fabric smoothness or durable-press (DP) ratingof such fabrics, and the DP rating of dry-cleaned fabrics, shallhave decreased no more than12 rating from that of the fabricbefore it i

34、s laundered or dry-cleaned.6.8 Flammability The flammability requirements shall beas agreed upon between the purchaser and the supplier,provided they meet or exceed applicable federal, state, or localmandatory standards.6.8.1 All slipcover fabrics shall be evaluated for cigaretteignition resistance

35、by the UFAC Fabric Classification TestMethod.7. Keywords7.1 fabric; performance; specification; upholsteryASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised tha

36、t determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reappro

37、ved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you fe

38、el that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual rep

39、rints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D4113 02 (2013)3