ASTM D4113-2002 Standard Performance Specification for Woven Slipcover Fabrics《机织家具套织物的标准性能规范》.pdf

《ASTM D4113-2002 Standard Performance Specification for Woven Slipcover Fabrics《机织家具套织物的标准性能规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM D4113-2002 Standard Performance Specification for Woven Slipcover Fabrics《机织家具套织物的标准性能规范》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 4113 02Standard Performance Specification forWoven Slipcover Fabrics1This standard is issued under the fixed designation D 4113; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in

2、parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This performance specification covers woven fabricscomprised of any textile fiber or mixture of fibers to be used inslipcovers.1.2 These require

3、ments apply to both the length and widthdirections for those properties where fabric direction is perti-nent.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety

4、 and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D 123 Terminology Relating to TextilesD 434 Test Method for Resistance to Slippage of Yarns inWoven Fabrics Using a Standard SeamD 1336 Test Method for Distortion

5、of Yarn in WovenFabricsD 1424 Test Method for Tearing Strength of Fabrics byFalling-Pendulum Type (Elmendorf) ApparatusD 2261 Test Method for Tearing Strength of Fabrics by theTongue (Single Rip) Procedure (Constant-Rate-of-Extension Tensile Testing Machine)D 2724 Test Methods for Bonded, Fused, and

6、 LaminatedApparel FabricsD 5034 Test Method for Breaking Strength and Elongationof Textile Fabrics (Grab Test)2.2 AATCC Test Methods:38 Colorfastness to Crocking: AATCC Crockmeter Method15 Colorfastness to Perspiration16 Colorfastness to Light23 Colorfastness to Burnt Gas Fumes61 Colorfastness to La

7、undering, Home and Commercial:Accelerated116 Colorfastness to Crocking: Rotary Vertical CrockmeterMethod124 Appearance of Fabrics After Repeated Home Launder-ings129 Colorfastness to Ozone in the Atmosphere Under HighHumidities132 Colorfastness to Drycleaning135 Dimensional Changes in Automatic Home

8、 Launderingof Woven or Knit Fabrics187 Dimensional Changes of Fabrics: AcceleratedEvaluation Procedure No. 1 Gray Scale for Color ChangeEvaluation Procedure No. 2 Gray Scale for StainingEvaluation Procedure No. 8 AATCC 9Step ChromaticTransference Scale2.3 Other Document:4UFAC Fabric Classification T

9、est Method for Cigarette Smol-der Resistance2.4 Military Standard5ASQ/ANSI Z1.4 Sampling Procedures and Tables for In-spection by AttributesNOTE 1Reference to test methods in this specification give only thepermanent part of the designation of ASTM, AATCC, or other testmethods. The current editions

10、of each test method cited shall prevail.3. Terminology3.1 Definitions:3.1.1 For definitions of textile terms used in this specifica-tion, refer to Terminology D 123 and the Technical Manual ofthe American Association of Textile Chemists and Colorists.3.2 Definitions found in a dictionary of common t

11、erms aresuitable for use in this specification.4. Specification Requirements4.1 The properties of woven fabrics for use in slipcoversshall conform to the specification requirements in Table 1.5. Significance and Use5.1 Fabrics intended for this end-use should meet all of therequirements listed inTab

12、le 1 .1This specification is under the jurisdiction of ASTM Committee D13 onTextiles and is the direct responsibility of Subcommittee D13.63 on HomeFurnishings.Current edition approved April 10, 2002. Published July 2002. Originallypublished as D 4113 82. Last previous edition D 4113 95a(2001).2For

13、referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American Association of Textile Chemists and Color

14、ists, P.O.Box 12215, Research Triangle Park, NC 27709.4Available from UFAC Central, Box 2436, High Point, NC 27261.5Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.1Copyright ASTM International, 100 Barr Harbor Drive,

15、PO Box C700, West Conshohocken, PA 19428-2959, United States.5.2 It should be recognized that fabrics can be producedwith an almost infinite number of combination of constructionvariables (for example, type of fibers, percentage of fibers, yarntwist, yarn number, warp and pick count, chemical andmec

16、hanical finishes). Additionally, fashion or aesthetics dictatethat the ultimate consumer may find acceptable articles madefrom fabrics that do not conform to all of the requirements inTable 1.5.2.1 Hence, no single performance specification can possi-bly apply to all the various fabrics that could b

17、e utilized for thisend-use.5.3 The uses and significance of particular properties andtest methods are discussed in the appropriate sections of thespecified test methods.6. Test Methods (see Note 1)6.1 Breaking Force Determine the dry breaking force, inthe standard atmosphere for testing textiles, as

18、 directed in TestMethod D 5034, using a constant rate of extension (CRE)tensile-testing machine.6.2 Resistance to Yarn SlippageDetermine the resistanceto yarn slippage as directed in Test Method D 434.NOTE 2The precision of Method D 434 is being established, and itmay not be suitable for fabrics wit

19、h low-yarn counts in terms of ends andpicks per inch (see 5.2).6.3 Tongue-Tear StrengthDetermine the tongue-tearstrength as directed in Test Method D 2261.6.4 Yarn Distortion Determine the yarn distortion asdirected in Test Method D 1336.6.5 Dimensional Change:6.5.1 LaunderingDetermine the maximum d

20、imensionalchange after five launderings as directed in the applicableprocedure in AATCC Test Method 135 or as agreed uponbetween the purchaser and the supplier (Note 3).6.5.1.1 The wash conditions and drying procedure shall beas specified by the supplier.6.5.2 Drycleaning Determine the maximum-dimen

21、sionalchange after three dry cleanings as directed in 10.1.1 through10.1.5 of Test Methods D 2724 or as agreed upon between thepurchaser and the supplier (Note 3).NOTE 3Launderable fabrics are expected to be dry-cleanable exceptwhere all or part of the fabric is not dry-cleanable and is so labeled.

22、Forexample, the fabric could contain a functional finish that is soluble in thesolvent, or the fiber could be degraded by the solvent, as would be the casewith poly(vinyl chloride) fiber. “Dry-cleanable” goods are to be dry-cleaned only.6.6 Colorfastness:6.6.1 Burnt Gas Fumes Determine the colorfast

23、ness toburnt gas fumes on the original fabric and after one launderingor one dry cleaning as directed in AATCC Test Method 23 after1 cycle.NOTE 4Washing conditions shall be the same as those used in 6.5.1.1.Dry-cleaning conditions shall be the same as those used in 6.5.2.6.6.2 LaunderingDetermine th

24、e colorfastness to launder-ing as directed in the applicable procedure of AATCC TestMethod 61. The test conditions shall be as specified by thesupplier (Note 3).6.6.3 Dry cleaningDetermine colorfastness to dry clean-ing as directed in AATCC Test Method 132 (Note 3).6.6.4 CrockingDetermine colorfastn

25、ess to dry and wetcrocking as directed in AATCC Test Method 8 for solid shadesand AATCC Test Method 116 for prints.6.6.5 Perspiration Determine colorfastness to perspira-tion as directed in AATCC Test Method 15.6.6.6 LightDetermine colorfastness to light as directed inAATCC Test Method 16.NOTE 5Ther

26、e are distinct differences in spectral distribution betweenthe various types of machines listed in AATCC Test Method 16, with nooverall correlations between them. Consequently, these machines cannotbe used interchangeably. In case of controversy, results obtained with theWater-Cooled Xenon-Arc machi

27、ne listed in Option E shall prevail.6.6.7 OzoneDetermine the colorfastness to ozone aftertwo cycles as directed in AATCC Test Method 129.6.7 Fabric AppearanceDetermine the fabric appearanceas directed in AATCC Test Method 124 after laundering usingthe wash-and-wear cycle or the normal cycle as agree

28、d uponbetween the purchaser and the supplier as specified in 6.5.1.1for washable fabrics or after dry cleaning as specified in 6.5.2for dry-cleanable fabrics (see Note 3).TABLE 1 Specification RequirementsNOTE 1Class for color change, color transfer, and DP rating is basedon a numerical scale of 5 f

29、or negligible or no color change, color transfer,or wrinkle to 1 for severe color change, color transfer, or wrinkle.Characteristic Requirements SectionBreaking strength (load)(CRT) 220 N (50 lbf)min6.1Yarn slippage 6-mm (14-in.) sepa-ration at 67 N(15 lbf), min6.2Tongue-tear strength 13 N (3.0 lbf)

30、 min 6.3Yarn distortion 2.5 mm (0.10 in),max at 9-N (2-lbf) load6.4Dimensional change:LaunderingDry cleaning2.5 %, max2.5 %, max6.5.16.5.2Colorfastness:Burnt gas fumes1 cycle: 6.6.1Shade change after one Grade 4A, minlaundering or onedry cleaningLaundering: 6.6.2Shade changeStainingGrade 4A, minGrad

31、e 3B, minDry cleaning: 6.6.3Shade change Grade 4A, minCrocking: 6.6.4DryWetGrade 4C, minGrade 3C, minPerspiration: 6.6.5Shade changeStainingGrade 4A, minGrade 3B, minLight (40 AATCC FU)(xenon-arc)Step 4A, min 6.6.6Ozone Grade 4, min 6.6.7Fabric appearance (see 6.7.1.1) SA 3.5D, min 6.7Flammability:

32、pass 6.8AAATCC Gray Scale for Color Change.BAATCC Gray Scale for Staining.CAATCC Chromatic Transference Scale.DFor durable press fabrics only.D41130226.7.1 For fabrics not intended for use in durable pressdetermine the fabric smoothness after pressing as specified in10.2.3 of Test Methods D 2724.6.7

33、.1.1 The fabric smoothness or durable-press (DP) ratingof such fabrics, and the DP rating of dry-cleaned fabrics, shallhave decreased no more than12 rating from that of the fabricbefore it is laundered or dry-cleaned.6.8 Flammability The flammability requirements shall beas agreed upon between the p

34、urchaser and the supplier,provided they meet or exceed applicable federal, state, or localmandatory standards.6.8.1 All slipcover fabrics shall be evaluated for cigaretteignition resistance by the UFAC Fabric Classification TestMethod.7. Keywords7.1 fabric; performance; specification; upholsteryASTM

35、 International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are ent

36、irely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsan

37、d should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee o

38、n Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D4113023