ASTM D4093-1995(2014) Standard Test Method for Photoelastic Measurements of Birefringence and Residual Strains in Transparent or Translucent Plastic Materials《透明或半透明塑性材料中双折射及残余应变的光.pdf

《ASTM D4093-1995(2014) Standard Test Method for Photoelastic Measurements of Birefringence and Residual Strains in Transparent or Translucent Plastic Materials《透明或半透明塑性材料中双折射及残余应变的光.pdf》由会员分享，可在线阅读，更多相关《ASTM D4093-1995(2014) Standard Test Method for Photoelastic Measurements of Birefringence and Residual Strains in Transparent or Translucent Plastic Materials《透明或半透明塑性材料中双折射及残余应变的光.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D4093 95 (Reapproved 2014)Standard Test Method forPhotoelastic Measurements of Birefringence and ResidualStrains in Transparent or Translucent Plastic Materials1This standard is issued under the fixed designation D4093; the number immediately following the designation indicates the year

2、 oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.INTRODUCTIONLight propagates in transparent materials at a speed, v,

3、 that is lower than its speed in vacuum, c. Inisotropic unstrained materials the index of refraction, n=cv,is independent of the orientation of theplane of vibration of light. Transparent materials, when strained, become optically anisotropic and theindex of refraction becomes directional. The chang

4、e in index of refraction is related to strains. If nois the refractive index of unstrained material, the three principal indices of refraction, ni, become linearfunctions of strain:ni no= AijjUsing photoelastic techniques (initially developed to measure stresses in transparent models) strains in pla

5、sticscan be assessed. In isotropic materials, two material constants, A and B, are sufficient to describe theiroptomechanical behavior:Aij= A when i = j, andAij= B when i fi j.When light propagates through a region (where principal strains 1and 2are contained in the plane perpendicularto the directi

6、on of light propagation (see Fig. 1), the incoming vibration splits into two waves vibrating in planes of1and 2. The difference between the indexes of refraction n1=cv1and n2=cv2(or birefringence) is:n1 n2=(A B)(1 1)=k(1 2)where k is a material property called the strain-optical constant. As a resul

7、t of their velocity difference, the wavesvibrating along the two principal planes will emerge out of phase, their relative distance, or retardation, , given by: =(n1 n2)t = kt(1 2)where t is the thickness of material crossed by the light.Asimilar equation, relating to the difference of principalstre

8、sses, 1and 2, can be written: =(n1 n2)t = Ct(1 2)The objective of photoelastic investigation is to measure: (a) the azimuth, or direction of principal strains, 1and2(or stresses 1and 2), and (b) the retardation, , used to determine the magnitude of strains. A complete theoryof photoelastic effect ca

9、n be found in the abundant literature on the subject (an extensive bibliography is providedin Appendix X2).1. Scope1.1 This test method covers measurements of directionofprincipal strains, 1and 2, and the photoelastic retardation, using a compensator, for the purpose of analyzing strains intranspare

10、nt or translucent plastic materials. This test methodcan be used to measure birefringence and to determine thedifference of principal strains or normal strains when theprincipal directions do not change substantially within the lightpath.1.2 In addition to the method using a compensator describedin

11、this test method, other methods are in use, such as thegoniometric method (using rotation of the analyzer) mostlyapplied for measuring small retardation, and expressing it as afraction of a wavelength. Nonvisual methods employing spec-trophotometric measurements and eliminating the human judg-ment f

12、actor are also possible.1This test method is under the jurisdiction ofASTM Committee D20 on Plasticsand is the direct responsibility of Subcommittee D20.10 on Mechanical Properties.Current edition approved Dec. 1, 2014. Published December 2014. Originallyapproved in 1982. Last previous edition appro

13、ved in 2010 as D4093 - 95 (2010).DOI: 10.1520/D4093-95R14.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States11.3 Test data obtained by this test method is relevant andappropriate for use in engineering design.1.4 The values stated in eit

14、her SI units or inch-pound unitsare to be regarded as standard.The values stated in each systemmay not be exact equivalents; therefore, each system shall beused independently of the other. Combining values from thetwo systems may result in nonconformance with the standard.1.5 This standard does not

15、purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.NOTE 1There is no known ISO equivalent to

16、this test method.2. Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD638 Test Method for Tensile Properties of PlasticsD882 Test Method for Tensile Properties of Thin PlasticSheetingD4000 Classification System for Specifying Plastic Materi-alsE691 Practice

17、for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method3. Terminology3.1 Definitions:3.1.1 compensatoran optical device used to measure re-tardation in transparent birefringent materials.3.1.2 polarizerpolarizing element transmitting light vi-brating in one plane only.3.1.

18、3 quarter-wave platea transparent filter providing arelative retardation of14 wavelength throughout the transmit-ting area.3.2 Definitions of Terms Specific to This Standard:3.2.1 birefringenceretardation per unit thickness, /t.3.2.2 retardation, distance (nm) between two wavefronts resulting from p

19、assage of light through a birefringentmaterial. (Also called “relative retardations.”)3.2.3 strain, -strain (or deformation per unit length)could be permanent, plastic strain introduced in manufacturingprocess, or elastic strain related to the existing state of stress.Both types of strains will prod

20、uce strain-birefringence in mostpolymers. Birefringence can also result from optical anisotropydue to crystalline orientation.3.2.4 strain-optical constant, kmaterial property, relatingthe strains to changes of index of refraction (dimensionless).k 5 n12 n2!/12 2!3.2.5 stress-optical constant, Cmate

21、rial property relatingthe stresses to change in index of refraction. C is expressed inm2/N or Brewsters (1012m2/N). C is usually temperature-dependent.C 5 n12 n2!/12 2!4. Summary of Test Method4.1 To analyze strains photoelastically, two quantities aremeasured: (a) the directions of principal strain

22、s and (b) theretardation, , using light paths crossing the investigatedmaterial in normal or angular incidence.4.2 The investigated specimen or sample is introducedbetween the polarizers (see Fig. 2 and Fig. 3). A synchronousrotation of polarizers follows until light intensity becomes zeroat the obs

23、erved location. The axes of the polarizers are thenparallel to direction of strains, revealing these directions.4.3 To suppress the directional sensitivity of the apparatus,the setup is changed, introducing additional filters.Acalibrated2For referenced ASTM standards, visit the ASTM website, www.ast

24、m.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.FIG. 1 Propagation of Light in a Strained Transparent MaterialD4093 95 (2014)2compensator is introduced and its setting adju

25、sted until lightintensity becomes zero at the observed location. The retarda-tion in the calibrated compensator is then equal and opposite insign to the retardation in the investigated specimen (see Fig. 4).5. Significance and Use5.1 The observation and measurement of strains in transpar-ent or tran

26、slucent materials is extensively used in variousmodeling techniques of experimental stress analysis.5.2 Internal strains induced in manufacturing processes suchas casting, molding, welding, extrusion, and polymer stretchingcan be assessed and part exhibiting excessive strains identified.Such measure

27、ments can lead to elimination of defective parts,process improvement, control of annealing operation, etc.5.3 When testing for physical properties, polariscopic ex-amination of specimens is required, to eliminate those speci-mens exhibiting abnormal internal strain level (or defects). ForFIG. 2 Tran

28、smission Set-up of PolariscopeFIG. 3 Reflection Set-up of PolariscopeD4093 95 (2014)3example: Test Methods D638 (Note 8) and D882 (Note 11)recommend a polariscopic examination.5.4 The birefringence of oriented polymers can be related toorientation, shrinkage, etc. The measurements of birefringenceai

29、d in characterization of these polymers.5.5 For many materials, there may be a specification thatrequires the use of this test method, but with some proceduralmodifications that take precedence when adhering to thespecification. Therefore, it is advisable to refer to that materialspecification befor

30、e using this test method. Table 1 of Classi-fication System D4000 lists theASTM materials standards thatcurrently exist.6. Apparatus6.1 The apparatus used to measure strains is shown sche-matically in Fig. 4. It consists of the following items:6.1.1 Light Source:6.1.1.1 Transmitted-Light Set-UpAn in

31、candescent lamp orproperly spaced fluorescent tubes covered with a diffusershould provide a uniformly diffused light. To ensure adequatebrightness, minimum illumination required is 0.3 W/in.2(0.0465 W/cm2). Maximum light source power is limited toensure that the specimen temperature will not change

32、morethan 2C during the test. The incandescent lamp must beselected to provide a color temperature no lower than 3150 K.There should be no visible nonuniformity, dark or bright spotson the diffuser surface, when no specimen is inserted in theapparatus.6.1.1.2 Reflection-Light SourceFor the reflection

33、 set-up anincandescent, reflector-equipped projection lamp is required.The lamp shall be equipped with proper lenses to ensureuniform illumination of the investigated object.At a distance of2 ft (610 mm) from the lamp an area of 1 ft2(0.093 m2) shouldbe illuminated, with no visible dark or bright sp

34、ots. The lamppower should be at least 150 W.6.1.2 PolarizerThe polarizing element shall be kept clean.The ratio of the transmittance of polarizers with their axesparallel, to the transmittance of the polarizers with their axesperpendicular to each other (or in crossed position), should notbe less th

35、an 500.Aglass-laminated construction of polarizers isrecommended. The polarizers must be mechanically or electri-cally coupled to insure their mutually perpendicular settingwhile rotated together to measure directions.Agraduated scalemust be incorporated to indicate the common rotation ofpolarizers

36、to a fixed reference mark.6.1.3 Quarter-Wave PlatesTwo quarter-wave plates arerequired in the procedure described below (see 9.2):6.1.3.1 The retardation of each quarter-wave plate shall be142 6 15 nm, uniform throughout its transmission area. Thedifference in retardation between the two quarter-wav

37、e platesshould not exceed 65 nm.6.1.3.2 The quarter-wave plates will be indexed, to permittheir insertion in the field of the apparatus with their axes at 45to the polarizers direction. The two quarter-wave plates shallhave their axes crossed (that is, their optical axes perpendicularto each other),

38、 thus insuring that the field remains at maximumdarkness when both quarter-wave plates are inserted (see Fig.5).6.1.4 CompensatorThe compensator is the essentialmeans of measuring retardation. The following types of com-pensators can be used:6.1.4.1 Linear Compensator3In the linear compensatorthe re

39、tardation in the compensator is linearly variable along itslength. A graduated scale shall be attached to the compensatorbody in such a manner that slippage cannot occur. Thecalibration characteristic of the compensator shall include theposition along its length (as indicated by the scale) of the li

40、newhere the retardation is zero and the number of divisions d per3Also known as “Babinet” compensator.FIG. 4 ApparatusD4093 95 (2014)4unit retardation (usually one wavelength). (The retardation perdivision is D= d.) The scale density shall be sufficient toprovide clear visibility for observing 1 % o

41、f the useful range ofthe compensator.6.1.4.2 Uniform Field Compensator4The uniform fieldcompensator is usually constructed from two optical wedgesmoved by means of a lead screw, the amount of relative motionbeing linearly related to the total thickness and the retardation.The lead screw motion shall

42、 be controlled by a dial drum orcounter. Calibration of this compensator shall include theposition, as indicated by the drum or counter, where theretardation is zero and the number of division of drum orcounter d per unit of retardation. (The retardation per divisionis D= d. )6.1.4.3 Compensators ha

43、ve a limited range of measuredretardation. In case the retardation in the sample exceeds therange of the compensator used, insertion of an offset retarder isneeded. The offset retarder must be calibrated and positionedalong the axes of the compensator, between the analyzer andthe sample.6.1.5 Filter

44、Monochromatic light is required to performvarious operations in photoelasticity and some operationscannot be successfully accomplished using white light. In thoseinstances a monochromatic light can be obtained introducingwithin the light path, a filter transmitting only light of thedesired wave leng

45、th. To best correlate with observation inwhite light, a narrow band-pass filter with peak transmittanceat 570 6 6 nm and a maximum transmitted band-width (athalf-peak point) of 10 nm should be used.7. Test Specimen7.1 Sheet, film, or more generally, a constant-thickness itemcan be examined using a t

46、ransmission set-up. For use inreflection, a reflecting surface must be provided. This can beaccomplished by painting one side of the specimen withaluminum paint.5Alternatively, it is possible to place theexamined sheet specimen against a clean metal surface (pref-erably aluminum) or an aluminum-pain

47、ted surface.7.2 Examination of complex surfaces or shapes sometimesrequires the use of an immersion liquid. The examined item isplaced inside a tank containing a liquid selected to exhibitapproximately the same index of refraction as the tested item.This technique is commonly used to examine three-d

48、imensional shapes.7.3 If conditioning is required, Procedure A of PracticeD618 shall be used.8. Calibration and Standardization8.1 A periodic verification (every 6 months) is required toensure that the apparatus is properly calibrated. The followingpoints require verification:8.1.1 Verification of P

49、olariscope:8.1.1.1 Verify that the polarizers remain in “crossed” posi-tion. A small deviation of one of the polarizers produces anincrease in the light intensity transmitted.8.1.1.2 Verify that the quarter-wave plates are properlycrossed. A small deviation of one quarter-wave plate from its“indexed” position will produce an increase in the lightintensity transmitted.8.1.2 Verification of the Compensator:8.1.2.1 Examine the compensator in the polariscope andverify that its = 0 point coincides with t