ASTM D4004-2006(2017) Standard Test Methods for Rubber&x2014 Determination of Metal Content by Flame Atomic Absorption (AAS) Analysis《橡胶的标准试验方法&x2014 采用火焰原子吸收(AAS)分析法测定金属含量》.pdf

《ASTM D4004-2006(2017) Standard Test Methods for Rubber&x2014 Determination of Metal Content by Flame Atomic Absorption (AAS) Analysis《橡胶的标准试验方法&x2014 采用火焰原子吸收(AAS)分析法测定金属含量》.pdf》由会员分享，可在线阅读，更多相关《ASTM D4004-2006(2017) Standard Test Methods for Rubber&x2014 Determination of Metal Content by Flame Atomic Absorption (AAS) Analysis《橡胶的标准试验方法&x2014 采用火焰原子吸收(AAS)分析法测定金属含量》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D4004 06 (Reapproved 2017)Standard Test Methods forRubberDetermination of Metal Content by Flame AtomicAbsorption (AAS) Analysis1This standard is issued under the fixed designation D4004; the number immediately following the designation indicates the year oforiginal adoption or, in the

2、case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 Th

3、ese test methods cover the determination of lead,zinc, copper, and manganese in raw rubber and rubbercompounds, vulcanized or unvulcanized. The level at whichthe metals are present is taken into account by suitableadjustments of sample mass and dilution.1.2 Certain compounding ingredients, present i

4、n the rubbersample will dictate which of the methods should be used. Referto Section 3. Five methods of determination are as follows:SectionsMethod A 8Method B 9Method C 10Method D 1422Method E 23311.3 The values stated in SI units are to be regarded asstandard. No other units of measurement are inc

5、luded in thisstandard.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior

6、to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarr

7、iers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D1076 Specification for RubberConcentrated, AmmoniaPreserved, Creamed, and Centrifuged Natural LatexD4483 Practice for Evaluating Precision for Test MethodStandards in the Rubber and Carbon Black ManufacturingIndustriesE663 Pra

8、ctice for Flame Atomic Absorption Analysis (With-drawn 1997)32.2 ISO Standards:ISO 1396 RubberCopper ContentPhotometric Technique-Determination4ISO 1655 RubberManganese ContentPhotometric Tech-niqueDetermination43. Summary of Test Methods3.1 Method ADetermination of lead and zinc in rubber notcontai

9、ning any halogen; in the case of lead, also not containingany silica filler. See Section 8.3.1.1 In Method A, the rubber is furnace-dried in a platinumcrucible at 250C, followed by furnace ashing for 1 to2hat550C. The ash is dissolved with the aid of concentratedhydrochloric acid (HCl) and the resul

10、ting solution suitablydiluted for Atomic Absorption Spectrometric (AAS) determi-nation of the lead and zinc.3.2 Method BDetermination of lead and zinc in rubbercontaining silica filler, but no halogen. See Section 9.3.2.1 In Method B the rubber is ashed in platinum as inMethod A. The ash is then fus

11、ed with a lithium or sodiumtetraborate or metaborate flux, after which the fused mixture isdissolved with the aid of HCl for subsequent AAS analysis.3.3 Method CDetermination of lead and zinc in rubbercontaining halogen. See Section 10.3.3.1 In Method C the rubber is wet-ashed with the aid ofconcent

12、rated sulfuric acid (H2SO4) and nitric acid (HNO3),evaporated to dryness, and further ashed in a muffle furnace at550C, after which the ash is dissolved as in Method A forsubsequent AAS analysis.1These test methods are under the jurisdiction of ASTM Committee D11 onRubber and Rubber-like Materials a

13、nd are the direct responsibility of SubcommitteeD11.11 on Chemical Analysis.Current edition approved May 1, 2017. Published May 2017. Originallyapproved in 1981. Last previous edition approved in 2012 as D4004 06 (2012).DOI: 10.1520/D4004-06R17.2For referenced ASTM standards, visit the ASTM website,

14、 www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from American Nationa

15、l Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardiz

16、ation established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.13.4 Method DDetermination of copper in raw rubber andrubber latex, both synthetic and natural

17、(see 14.2).3.4.1 In Method D the rubber is ashed at 550C, the ash isthen digested in hydrochloric acid, and copper is determined byAAS analysis.3.5 Method EDetermination of manganese in raw naturalrubber and rubber latex, both synthetic and natural (see 23.2).3.5.1 In Method E the rubber is ashed at

18、 550C, the ash isdigested in hydrochloric acid and the manganese is determinedby AAS analysis.3.5.2 See 3.6.3.6 Because this standard does not contain procedures foroptimizing instrument performance, nor does it instruct theanalyst in the basics of flame atomic absorption, it is recom-mended that th

19、e references found in Section 2 be studied forthese purposes.4. Significance and Use4.1 These test methods are suitable for process control, forproduct acceptance, and for research and development.5. Apparatus5.1 Laboratory Balance.5.2 Laboratory Muffle Furnace.5.3 Hot Plate.5.4 Platinum Crucibles,

20、25 cm3content minimum.5.5 Common Borosilicate Glassware.5.6 Meker Burner.5.7 Atomic Absorption Spectrophotometer, operated in ac-cordance with the manufacturers directions for optimuminstrument performance.6. ReagentsNOTE 1Observe all recognized health and safety precautions whilecarrying out this p

21、rocedure.6.1 All reagents used shall be of analytical grade anddistilled de-ionized water (DDW) shall be used for anydilutions.6.2 Hydrochloric Acid (HCl) (density 1.19 Mg/m3).6.3 Hydrochloric Acid (6 M)Dilute concentrated HClwith an equal volume of water.6.4 Lithium Carbonate (Li2CO3).6.5 Lithium M

22、etaborate (LiBO2).6.6 Lithium Tetraborate (Li2B4O7).6.7 Nitric Acid (HNO3) (density 1.42 Mg/m3).6.8 Sodium Carbonate (Na2CO3).6.9 Sodium Tetraborate (Na2B4O710 H2O).6.10 Sulfuric Acid (H2SO4) (density 1.83 Mg/m3).7. Sampling7.1 Selection of a test portion shall be at the discretion of theanalyst and

23、 shall be as representative of the sample as possible.METHOD A8. Procedure8.1 Weigh 0.1 g of dry rubber into a platinum 25-cm3or50-cm3crucible if lead and zinc are present at levels higherthan 0.5 %. Weigh a larger amount (up to 10 g) when the leadand zinc levels are lower. Record the mass of rubber

24、, W,tothenearest 0.1 mg.8.2 Place the test portion in the muffle furnace at 250C for0.5 h. Raise the temperature to 550C for 1 h. If not completelyashed, continue ashing for another hour or two.8.3 Cool the crucible to room temperature and add 5 cm3of6 M HCl. Heat on a hot plate until the ash is com

25、pletelydissolved and transfer quantitatively to a 25-cm3volumetricflask. Fill to the mark with DDW. For lead levels less than 10mg/kg (g/g) dissolve the ash in 2 cm3of 6 M HCl and transferto a 10-cm3volumetric flask.8.4 Determine the lead and zinc by AAS following PracticeE663. Keep the matrix of th

26、e blank, of the standard, and of thesample solutions as identical as possible. Any necessarydilutions of the sample solution are carried out with DDW.METHOD B9. Procedure9.1 Ash in platinum crucibles as described under 8.1 and 8.2using1gofrubber.9.2 To the ash obtained, add1gofa3-to-1 mixture ofsodi

27、um carbonate (Na2CO3) and sodium tetraborate(Na2B4O710 H2O) and mix the compounds using a cleanquartz or platinum rod. Fuse the mixture for a few minutes overa Meker burner. Using platinum-tipped tongs, turn the crucible,so that all of the mixture fuses properly.NOTE 2Alternative fusing agents are a

28、 3-to-1 mix of lithium carbon-ate (Li2CO3) and lithium tetraborate (Li2B4O7), and lithium metaborate(LiBO2) which, in that order, fuse at somewhat higher temperatures.9.3 Cool to room temperature and dissolve the fused masswith 5 cm3of 6 M HCl. Magnetic stirring will speed up thedissolution. If nece

29、ssary, add 5 to 10 cm3of DDW to aidsolution.9.4 Transfer the solution quantitatively to a 25-cm3volu-metric flask. Fill to the mark with DDW.9.5 Continue as set out in 8.4.METHOD C10. Procedure10.1 Weigh1gofrubber in the form of small pieces in aplatinum crucible or borosilicate beaker.10.2 Add 25 c

30、m3of concentrated H2SO4and heat on a hotplate until the rubber is disintegrated (approximately 0.5 to1 h).10.3 Cool to room temperature and add dropwise 10 cm3ofconcentrated HNO3.D4004 06 (2017)210.4 Heat on a hot plate until the solution has become clear(approximately 1 to 3 h). Then evaporate to d

31、ryness and ash theresidue in a muffle furnace at 550C.10.5 Continue as set out in 8.3 and 8.4.11. Test Report11.1 The report shall include the following:11.1.1 The amount of lead and zinc found in the rubber totwo significant figures either in percent or mg/kg (ppm),11.1.2 The test method used,11.1.

32、3 Graph of absorbances versus concentrations for thelead and zinc standards,11.1.4 Absorbances measured on the sample test solutions,11.1.5 A listing of instrumental conditions such as lampcurrent, wavelength of the analytical line, type of flame, andtype of burner,11.1.6 Calculation of the lead and

33、 zinc concentrations in theoriginal rubber, and11.1.7 Notes on any unusual observations both with respectto the chemical procedure and the instrumental determination.12. Limits of Detection12.1 The limits of detection with acceptable error for aminimum absorbance of 0.050 are listed as a function of

34、sample mass and final dilution volume. See Table 1.13. Precision and Bias513.1 These precision statements have been prepared inaccordance with Practice D4483. Please refer to this practicefor terminology and other testing and statistical conceptexplanations.13.2 Precision data obtained at the 3 % Zn

35、 and 1 % Pb levelare as follows:13.2.1 Zinc PrecisionThe Type 1 precision is estimatedfrom an interlaboratory study by six laboratories testing threematerials on three days. A test result is the average of duplicatedeterminations.13.2.1.1 The Type 1 precision is expressed in absolute termsas percent

36、age points. See Table 2.13.3 Lead PrecisionThe Type 1 precision is estimatedfrom an interlaboratory study by six laboratories testing threematerials on three days. A test result is the average of duplicatedeterminations.13.3.1 The Type 1 precision is expressed in absolute termsas percentage points.

37、See Table 3.13.4 Precision data obtained at the mg/kg (ppm) level are asfollows:13.4.1 Zinc Precision: The Type 1 precision is estimatedfrom an interlaboratory study by five laboratories testing threematerials on three days. A test result is the average of duplicatedeterminations (see Table 4).13.4.

38、1.1 Concentrations less than 1 mg/kg (ppm) cannot beprecisely determined by this test method.13.4.2 Lead PrecisionThe Type 1 precision is estimatedfrom an interlaboratory study by five laboratories testing twosamples on three days. A test result is an average of duplicatedeterminations (see Table 5)

39、.13.4.2.1 Concentrations less than 1 mg/kg (ppm) cannot beprecisely measured by this test method.13.5 See also Section 31 for additional discussion of preci-sion.METHOD D14. Significance and Use14.1 See 4.1.14.2 Copper in certain forms is known to catalyze theoxidative breakdown of natural rubber al

40、though the mechanismby which degradation is brought about is not fully understood.It is recognized that other forms of copper can be present in therubber even in relatively large amounts without degradationtaking place, but in these cases there is always the possibilitythat under the influence of so

41、me chemicals, notably the5Supporting data have been filed at ASTM International Headquarters and maybe obtained by requesting Research Report RR:D11-1020. ContactASTM CustomerService at serviceastm.org.TABLE 1 Limits of DetectionAMethod A Method B Method CSample mass (g) 10 1 1Total volume (cm3)1 0

42、0Zinc 0.1 2.5 1.0Lead 1.0 25.0 1.0AThe limits of detection for Method C can only be realized if extremely pure acidsare used for the digestion. With the usual reagent grade acids, even when acorrection is applied on the basis of a blank digestion, the limit of determination islikely a factor of ten

43、to one hundred higher.TABLE 2 Type 1 PrecisionZinc (Normal Level)NOTE 1Sr = repeatability standard deviation, in measurement units.r = repeatability, in measurement units.(r) = repeatability, (relative) percent.SR = reproducibility standard deviation, in measurement units.R = reproducibility, in mea

44、surement units.(R) = reproducibility, (relative) percent.MaterialAverageLevel,%WithinLaboratoriesBetweenLaboratoriesSr r (r) SR R (R)6 2.90 0.0996 0.306 10.6 0.108 0.282 9.762 3.00 0.113 0.320 10.7 0.134 0.379 12.64 3.01 0.116 0.328 10.9 0.133 0.375 12.5TABLE 3 Type 1 PrecisionLead (Normal Level)NOT

45、E 1Sr = repeatability standard deviation, in measurement units.r = repeatability, in measurement units.(r) = repeatability, (relative) percent.SR = reproducibility standard deviation, in measurement units.R = reproducibility, in measurement units.(R) = reproducibility, (relative) percent.MaterialAve

46、rageLevel,%WithinLaboratoriesBetweenLaboratoriesSr r (r) SR R (R)2 0.82 0.0264 0.0747 9.11 0.0754 0.213 26.04 0.91 0.0296 0.0838 9.23 0.0785 0.222 24.46 0.92 0.0363 0.103 11.2 0.0856 0.242 26.3D4004 06 (2017)3unsaturated acids, the copper could assume a more aggressiverole when the rubber is compoun

47、ded.14.3 It would be advantageous to be able to analyticallydistinguish between catalytically active and inactive forms ofcopper but no generally accepted method has yet been putforward to doing so. There is no alternative therefore, but todetermine the total amount of copper in the rubber.14.4 Litt

48、le is known concerning the influence of copper onthe catalytic oxidation of synthetic rubbers, although it iswidely accepted that its effect is less severe than in the case ofnatural rubber. Possibly for this reason, the determination ofcopper in compounds based on the synthetic rubbers is lessfrequ

49、ently carried out.615. Limitations15.1 This test method should not be used for copper contentof heavily loaded rubbers, which contain silica and clay, unlessit has been determined that these fillers do not interfere with thetest method as written.16. Apparatus16.1 See Section 5.17. Reagents17.1 See Section 6.18. Sampling18.1 See Section 7.19. Sample Preparation19.1 Raw rubber may be milled or cut into small pieces.19.2 Latex should be prepared in the form of a filmaccording to Specification D1076, Section 5. It is not necessaryto weigh the sam