ASTM D3883-2004(2016) Standard Test Method for Yarn Crimp and Yarn Take-up in Woven Fabrics《机织织物中纱线卷曲性和织缩性的标准试验方法》.pdf

《ASTM D3883-2004(2016) Standard Test Method for Yarn Crimp and Yarn Take-up in Woven Fabrics《机织织物中纱线卷曲性和织缩性的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM D3883-2004(2016) Standard Test Method for Yarn Crimp and Yarn Take-up in Woven Fabrics《机织织物中纱线卷曲性和织缩性的标准试验方法》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D3883 04 (Reapproved 2016)Standard Test Method forYarn Crimp and Yarn Take-up in Woven Fabrics1This standard is issued under the fixed designation D3883; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last

2、 revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of the rela-tionship between the length of a piece of fabric and the lengthof th

3、e yarn in the fabric by measurement of the yarn crimp andyarn take-up.1.2 This test method applies to woven fabrics.1.3 The values stated in either SI or inch-pound units are tobe regarded separately as standard. Within the text, theinch-pound units are shown in parentheses. The values statedin each

4、 system are not exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in nonconformancewith the specification.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is t

5、heresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD1776/D1776M Practice for Conditioning and Testi

6、ng Tex-tilesD2904 Practice for Interlaboratory Testing of a Textile TestMethod that Produces Normally Distributed Data (With-drawn 2008)3D2906 Practice for Statements on Precision and Bias forTextiles (Withdrawn 2008)3D4849 Terminology Related to Yarns and FibersD4850 Terminology Relating to Fabrics

7、 and Fabric TestMethods3. Terminology3.1 For definition of textile terms used in this test method:bench marks, refer to Terminology D4849.3.2 For definitions of textile terms used in this test method:yarn crimp and yarn take-up, refer to Terminology D4850.3.3 For definitions of other textile terms u

8、sed in this testmethod, refer to Terminology D123.4. Summary of Test Method4.1 Bench marks are placed on a length of a yarn as it liesin a woven fabric. The distance between the bench marks ismeasured. The yarn is removed from the fabric, straightened byapplying suitable tension, and the distance be

9、tween the benchmarks is remeasured. Yarn crimp is the change in lengthexpressed as a percent and based on the in-fabric distance. Yarntake-up is the change in length expressed as a percent andbased on the out-of-fabric distance.5. Significance and Use5.1 The relationship of the length of a piece of

10、fabric and thelength of yarn in the fabric can be determined accurately onlybe measuring the length of yarn entering the loom and thelength of fabric made from that particular length of yarn. Inmost cases, however, the determination must of necessity bemade on a woven fabric by measuring the length

11、of yarnremoved from a measured length of fabric, thus introducingcertain variations that will influence the accuracy of the test.Yarn removed from the woven fabric contains undulations orwaves that have been introduced by the weaving process. Heat,moisture, and mechanical shrinkage on subsequent fin

12、ishingoperations may accentuate these undulations, and in allprobability, increase the force to pull them out and straightenthe yarn. In order to accurately measure the length of the yarnafter the removal of the crimp, these undulations must bepulled out without elongating the yarn. In some cases, t

13、heminimum force necessary to straighten the yarn will cause acertain amount of the elongation to take place, thus increasingthe length of the yarn. Also, stresses imposed upon the yarnduring the weaving process may have been sufficient to stretchthe yarn beyond its elastic limit, again increasing it

14、s length. Itis recognized that determination made by measuring length ofyarn removed from a measured length of fabric may tend togive crimp values that are somewhat higher than the crimp in1This test method is under the jurisdiction of ASTM Committee D13 on Textilesand is the direct responsibility o

15、f Subcommittee D13.59 on Fabric Test Methods,General.Current edition approved July 1, 2016. Published July 2016. Originally approvedin 1980. Last previous edition approved in 2012 as D3883 04(2012). DOI:10.1520/D3883-04R16.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orconta

16、ct ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International, 100 Barr Harbor Drive, P

17、O Box C700, West Conshohocken, PA 19428-2959. United States1the yarn as it lay in the fabric. In the case of fabrics made fromyarns that exhibit differential shrinkage, or yarns of widelydifferent count, or yarns woven at different tensions, the crimpof each type of yarn in the fabric must be determ

18、ined andreported separately.5.2 This test method can be used for acceptance testing ofcommercial shipments but comparisons should be made withcaution because information on estimates of between-laboratory precision is limited as noted in 13.1.5.2.1 If there are differences of practical significance

19、be-tween reported test results for two laboratories (or more),comparative tests should be performed to determine if their isa statistical bias between them, using competent statisticalassistance. As a minimum, ensure the test samples to be usedare as homogeneous as possible, are drawn from the mater

20、ialfrom which the disparate test results were obtained, and arerandomly assigned in equal numbers to each laboratory fortesting. The test results from the two laboratories should becompared using a statistical test for unpaired data, at aprobability level chosen prior to the testing series. If a bia

21、s isfound, either its cause must be found and corrected, or futuretest results for that material must be adjusted in considerationof the known bias.6. Apparatus6.1 Suitable Device4, for straightening the yarn throughapplication of horizontal or vertical tension, having two yarnsupport surfaces or tw

22、o clamps, the distance between whichmay be altered in order to apply the needed tension.6.2 Suitable Marking Device, for marking bench marks onthe yarn specimen.7. Sampling and Test Specimens7.1 Primary Sampling UnitConsider rolls of fabric orfabric components of fabricated systems to be the primary

23、sampling unit, as applicable.7.2 Laboratory Sampling UnitAs a laboratory samplingunit take from rolls two pieces of fabric, full width, each 375mm (15 in.) in length along the selvage (machine direction)after removing a first 1-mm (1-yd) length. For fabric compo-nents of fabricated systems use the e

24、ntire system.7.3 Test SpecimensFrom each laboratory sampling unit, asrequired for each the warpwise and fillingwise directions, taketen test specimens, each 300 mm (14 in.) long as direction inSection 9. Consider the long direction as the direction of test.7.3.1 For fabric widths 125-mm (5-in.) or m

25、ore, take nospecimen closer than 25-mm (1-in.) from the selvage edge.7.3.2 For fabric widths less than 125-mm (5-in.), use theentire width for specimens.7.3.3 Ensure specimens are free of folds, creases, orwrinkles. Avoid getting oil, water, grease, etc., on the speci-mens when handling.7.3.4 If the

26、 fabric has a pattern, ensure that the specimensare a representative sampling of the pattern.8. Conditioning8.1 Condition the specimens by bringing them to approxi-mate moisture equilibrium in the standard atmosphere forconditioning textiles as directed in Practice D1776/D1776M.9. Preparation of Tes

27、t Apparatus and Calibration9.1 Set-up procedures for machines from different manufac-turers may vary. Prepare and verify calibration of the testingdevice as directed in the manufacturers instructions.10. Procedure10.1 Test the specimens in the standard atmosphere fortesting textiles, as described in

28、 Practice D1776/D1776M.10.2 Handle the test specimens carefully to avoid alteringthe natural state of the material.10.3 Test ten specimens from the warpwise direction or tenspecimens from the fillingwise direction, or both, as required ina material specification or contact order.10.4 Using the marki

29、ng device, make two lines (benchmarks) 250 mm (10 in.) apart, perpendicular to the yarn beingtested and extending 25 mm (1 in.) into the fabric, and recordthe distance between bench marks as distance (F) (in-fabricdistance).10.4.1 If a direct reading device is used, follow the manu-facturers recomme

30、ndations for establishing the specimenlength.10.5 Prepare an edge by making a cut at least 350 mm (14in.) long, parallel, and in the direction of the yarn to bemeasured, and such that it crosses near the ends of both linesof the bench mark.10.6 Ravel several yarns from the cut edge, such that theyco

31、ntain the bench marks.10.7 One at a time, when ready to use, ravel ten yarnspecimens from the prepared edge of the fabric. Ensure that thebench marks appear on each yarn. Take care not to disturb thetwist or strain the yarn. Maintain identity of the fabric directionbeing evaluated, that is, warpwise

32、 or fillingwise.10.8 Fasten one of the yarn specimens in the clamps of atensioning device or, if applicable, in the proper position of theyarn supports of a direct reading crimp tester with the benchmarks coincident with the nips of the respective clamps that areset for the initial in-fabric length.

33、10.8.1 Clamp type devices may consist of a twist counterfitted with graduated sliding clamp, or a tension testingmachine or which the movement or action can be stoppedinstantly at any point, such as the constant-rate-of-elongation(CRE-Type) or other similar instrument. For a direct readingcrimp test

34、er, the yarn is placed under the hook of the movableshaft with the bench marks on the yarn aligned with the upperfixed yarn supports.10.9 Apply a force to the yarn just sufficient to removeundulations due to weaving, without imparting stretch asdetermined by using one of the following three options.

35、4Commercially available devices that have been found acceptable are a twisttester with tension device, a tensile testing machine, and a crimp tester of the directreading type.D3883 04 (2016)2NOTE 1The three options can give different results. For maximumprecision between laboratories, it is recommen

36、ded that the laboratories usethe same equipment and the same option.10.9.1 Option A, By HandStraighten the yarn by handagainst a scale graduated in 1 mm (116 in.), observe and recordthe distance between bench marks to the nearest 1 mm (116 in.)as (Y) (straightened yarn distance).NOTE 2This is the le

37、ast accurate option because the tension requiredto remove crimp is unknown.10.9.2 Option B, by Tension Device or Crimp TesterUsingone of the tensioning devices or crimp tester, apply a tensionforce based upon the known yarn size. If the tension force isnot sufficient to remove all the crimp, gradual

38、ly increase thetension force until the crimp just removed. Use the determinedforce on all the yarns in the set and proportional force on anyother samples in the series or test.10.9.2.1 Estimate the required tension force using Eq 1:Tensile force, g 5 yarn number in tex 30.25 (1)10.9.3 Option C, Tens

39、ile Testing MachineUsing aconstant-rate-of-extension (CRE-type) of testing machine, de-termine the force to remove undulations by analysis of aforce-extension as described in 10.9.3.1.10.9.3.1 Establish Point A as the point where the force-extension curve begins, that is, zero force and zero extensi

40、on.Extrapolate the straight-line portion of the force-extensioncurve through the extension axis, Line CE. The portion of thecurveAD represents the removal of the crimp and initial stretchof the yarn. Establish Point D where the force-extension curveseparates from the line CE. Establish Point B by co

41、nstructinga line from Point C, parallel to the force axis to curve AD.Establish Point L by constructing a line from Point B throughthe force axis, parallel to the extension axis. The forcecorresponding to Point L is the required tensile force to removethe crimp without stretching (see Fig. 1).10.10

42、Determine and record the length of the yarn to thenearest 2.5 mm (0.1 in.) after removal of the crimp as follows:10.10.1 For clamp-type devices, measure the distance be-tween the bench marks on the straightened yarn and record asdistance (Y) (straightened yarn distance).10.10.2 For constant-rate-of-

43、extension machines, determineand record the straightened distance (Y) between bench marksdirectly from the extension axis of the force-extension curveillustrated on Fig. 1 by line LB, projected to the extension axis,allowing for any chart magnification ratio.10.10.2.1 For some tensile testers, strai

44、ghtened yarn dis-tance (Y) and the percent yarn crimp or yarn take-up can becomputer-processed automatically.10.10.3 For direct-reading crimp testers, read the yarn crimpor yarn take-up directly from the dial or scale.11. Calculation11.1 Calculate the average distance between the two benchmarks on t

45、he straightened yarn for all measured specimens tothe nearest 2.5 mm (0.1 in.), for each warpwise direction andfillingwise direction, as applicable.11.2 Calculate the average yarn crimp or average yarntake-up to the nearest 0.1 % using Eq 2 or Eq 3, for eachwarpwise direction and fillingwise directi

46、on, as applicable:C 5 100Y 2 F!/F (2)T 5 100Y 2 F!/Y (3)where:C = yarn crimp, %,T = yarn take-up, %,F = average of distances between bench marks on yarn infabric, mm (in.) (from 10.4), andY = average of distances between bench marks on yarn afterremoval from fabric and straightened under tension, mm

47、(in.) (from 10.10).11.2.1 When data are computer-processed automatically,calculations generally are contained in the associated software.It is recommended that computer processed data be verifiedagainst known property values and its software described in thereport.11.2.2 For direct-reading crimp tes

48、ters, the yarn crimp oryarn take-up is read directly from the dial or scale.12. Report12.1 The report shall contain the following information:12.1.1 Report that the yarn crimp and yarn take-up wasdetermined as directed in Test Method D3883. Describe thematerial or product sampled and the method of s

49、ampling used.FIG. 1 Example Chart For Determining of Tensile Force Using Op-tion CD3883 04 (2016)312.1.2 Report the following information for the warpwiseand fillingwise directions for the laboratory sampling unit andfor the lot as applicable to a material specification or contractorder.12.1.2.1 Average yarn crimp and average yarn take-up;12.1.2.2 Test option, manufacturer, and model of test instru-ment;12.1.2.3 Force used to remove crimp;12.1.2.4 When calculated, the standard deviation or thecoefficient of variation.12.1.2.5 For computer-processed data, identify the