ASTM D3815 D3815M-2005(2011) Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Open-Flame Carbon-Arc Exposure Apparatus《用明火碳弧暴露试验机 加速风化压敏胶带的标准操作规程》.pdf

《ASTM D3815 D3815M-2005(2011) Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Open-Flame Carbon-Arc Exposure Apparatus《用明火碳弧暴露试验机 加速风化压敏胶带的标准操作规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM D3815 D3815M-2005(2011) Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Open-Flame Carbon-Arc Exposure Apparatus《用明火碳弧暴露试验机 加速风化压敏胶带的标准操作规程》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D3815/D3815M 05 (Reapproved 2011)Standard Practice forAccelerated Weathering of Pressure-Sensitive Tapes byOpen-Flame Carbon-Arc Exposure Apparatus1This standard is issued under the fixed designation D3815/D3815M; the number immediately following the designation indicates theyear of ori

2、ginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of D

3、efense.1. Scope1.1 This practice describes one environment for the expo-sure of pressure-sensitive tapes to a laboratory acceleratedweathering environment.1.2 This practice describes sample preparation and thelaboratory-accelerated weathering environment to which itshall be exposed. It does not spec

4、ify the length of time of theexposure nor what tests shall be performed on the materialfollowing the exposure.NOTE 1Practice D6551/D6551M describes xenon-arc exposures oftapes.1.3 The values stated in either SI or inch-pound units are tobe regarded separately as standard. The values stated in eachsy

5、stem may not be exact equivalents; therefore, each systemmust be used independently without combining values in anyway.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-pri

6、ate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2A666 Specification for Annealed or Cold-Worked Auste-nitic Stainless Steel Sheet, Strip, Plate, and Flat BarD3330/D3330M Test Method for Peel Adhesion of

7、Pressure-Sensitive TapeD3715/D3715M Practice for Quality Assurance ofPressure-Sensitive TapesD6551/D6551M Practice for Accelerated Weathering ofPressure-Sensitive Tapes by Xenon-Arc Exposure Appara-tusG147 Practice for Conditioning and Handling of Nonmetal-lic Materials for Natural and Artificial We

8、athering TestsG151 Practice for Exposing Nonmetallic Materials in Ac-celerated Test Devices that Use Laboratory Light SourcesG152 Practice for Operating Open Flame Carbon Arc LightApparatus for Exposure of Nonmetallic Materials3. Summary of Practice3.1 The pressure-sensitive tape is exposed in accor

9、dancewith the conditions provided by Practices G151 and G152.Exposure time is determined by applicable material specifica-tion or by mutual agreement by all interested parties.4. Significance and Use4.1 This practice does not necessarily provide direct simu-lation of natural weathering exposure.4.2

10、Results from use of this practice shall not be representedas being equivalent to those of any natural weathering test untila satisfactory degree of correlation has been established for thematerial in question.4.3 Variations in results are possible when the operatingconditions vary within the accepte

11、d limits for the instrumentspecified in Practices G151 and G152.5. Apparatus5.1 Exposure Apparatus, conforming to the requirementsdefined in Practices G151 and G152 for exposure using theopen-flame carbon arc with daylight filters.5.2 Panels, for holding or supporting the specimens ap-proximately 75

12、 by 225 mm 3 by 9 in. and rigid enough toresist deforming during use.5.2.1 The material shall be Type 302 or 304 stainless steel inaccordance with Specification A666 having a bright annealedfinish. The surface roughness height shall be 50 6 5 mm 2.06 0.1 -in. arithmetical average deviation from the

13、mean line.5.2.2 Other dimensions or materials and finishes are accept-able when defined by the subsequent test standard or commod-ity specification.1This practice is under the jurisdiction of ASTM Committee D10 on Packagingand is the direct responsibility of Subcommittee D10.14 on Tape and Labels.Cu

14、rrent edition approved Aug. 1, 2011. Published November 2011. Originallyapproved in 1979. Last previous edition approved in 2005 as D3815/D3815M 05.DOI: 10.1520/D3815_D3815M-05R11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org

15、. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.2.3 A panel or frame of the dimensions required by theexposure a

16、pparatus may be used to support the specimen panelwhen it is more convenient to do so, as long as the light andwater paths are not interrupted or shortened by doing so.5.3 Rubber-Covered Roller, at least as wide as the specimenwith any diameter and rubber hardness.6. Sampling6.1 Sampling shall be in

17、 accordance with the requirementsof the applicable material or commodity specification.6.2 Lacking the previously mentioned specification, sam-pling shall be in accordance with the physical property methodapplicable to the testing to follow the exposure.6.3 When no other sampling requirement is appl

18、icable,sampling shall be in accordance with Practice D3715/D3715M.7. Test Specimens7.1 Unless otherwise specified, prepare and expose at leastthree replicate specimens of each tape to be tested. The testspecimen dimensions shall be in accordance with the standardto be used subsequent to this exposur

19、e or the commodityspecification.7.2 Unwind and discard at least three, but no more than six,outer wraps of tape from the sample roll before takingspecimens for testing.7.3 Remove specimens from a freely rotating roll at the rateof 500 to 750 mm 20 to 30 in./s. Where width or other factorscausing a h

20、igh adherence to backing make it impossible toremove the specimen at the prescribed rate, remove it at a rateas close to 500 mm 20 in./s as possible.7.4 Follow the procedures described in Practice G147 foridentification, conditioning, and handling of test specimensprior to, during, and after exposur

21、e.8. Procedure8.1 Apply the specimen as directed by the standard to beused subsequent to this exposure. If none, apply the specimen,centered lengthwise, to the panel using the rubber-coveredroller (5.3), holding the specimen so that the roller causes thefirst contact of specimen with the panel.8.1.1

22、 When a test, such as in Test Method D3330/D3330M,is to follow this exposure, it is customary to apply the tape tothe prescribed panel in accordance with Test Method D3330/D3330M preparatory to the exposure and peel it withoutreapplication following the exposure.8.1.2 It is usually assumed that it i

23、s the backside of thepressure-sensitive tape that is to receive the energy. Anydeviation from this would be expressed by the commodityspecification.8.2 Expose specimens in the open-flame carbon arc appa-ratus in accordance with Practice G151 and Cycle 1 of PracticeG152 using continuous light and a t

24、est cycle consisting of 102min light only followed by 18 min of light with water sprayedon the front surface of the specimens. The uninsulated blackpanel temperature is controlled at equilibrium at 63C at thecontrol point. The maximum operational fluctuation allowed is63C. The chamber air temperatur

25、e shall be controlled at 44Cat the control point with a maximum operational fluctuation of62C. Apparatus equipped with means of humidification shallbe operated with the humidifier turned off. The total time ofexposure shall be as specified in the material specification.8.3 Expose the specimens accor

26、ding to Cycle 1 of PracticeG152. Apparatus equipped with means of humidification shallbe operated with the humidifier turned off. The total time ofexposure shall be as specified in the material specification.8.4 Follow the instructions of the commodity specificationrelative to observations, physical

27、 tests, or both to be performedon the specimens following the exposure. Determine theaverage of the result for physical property tests performed onthe specimens.9. Report9.1 In reporting data, including observations, obtained byany examination following this exposure, make reference tothis practice

28、by designation. Provide the following informa-tion:9.1.1 Any deviation from this practice and any items refer-enced in the Report section of Practices G151 and G152, and9.1.2 The information required by the subsequent standard.10. Keywords10.1 accelerated weathering; open-flame carbon-arc expo-sure

29、apparatus; pressure-sensitive tapeD3815/D3815M 05 (2011)2ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such paten

30、t rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited eithe

31、r for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair he

32、aring you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standar

33、d may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D3815/D3815M 05 (2011)3