ASTM D3595-2014 Standard Specification for Polychlorotrifluoroethylene &40 PCTFE&41 Extruded Plastic Sheet and Film《聚三氟氯乙烯挤压塑料薄板及薄膜标准规格》.pdf

《ASTM D3595-2014 Standard Specification for Polychlorotrifluoroethylene &40 PCTFE&41 Extruded Plastic Sheet and Film《聚三氟氯乙烯挤压塑料薄板及薄膜标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM D3595-2014 Standard Specification for Polychlorotrifluoroethylene &40 PCTFE&41 Extruded Plastic Sheet and Film《聚三氟氯乙烯挤压塑料薄板及薄膜标准规格》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D3595 14Standard Specification forPolychlorotrifluoroethylene (PCTFE) Extruded Plastic Sheetand Film1This standard is issued under the fixed designation D3595; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year o

2、f last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers extruded sheet and film inthicknesses from 0.015 to 0.25 mm (0.0006 to 0.01 in.).1.2 The

3、values stated in SI units shall be regarded as thestandard.1.3 The following precautionary statement pertains only tothe test methods portion, Section 9 of this specification:Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility

4、 of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.NOTE 1There is no known ISO equivalent to this standard.2. Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for Test

5、ingD882 Test Method for Tensile Properties of Thin PlasticSheetingD883 Terminology Relating to PlasticsD1204 Test Method for Linear Dimensional Changes ofNonrigid Thermoplastic Sheeting or Film at ElevatedTemperatureD1430 Classification System for Polychlorotrifluoroethylene(PCTFE) PlasticsD1600 Ter

6、minology forAbbreviated Terms Relating to Plas-ticsD3892 Practice for Packaging/Packing of PlasticsF1249 Test Method for Water Vapor Transmission RateThrough Plastic Film and Sheeting Using a ModulatedInfrared SensorIEEE/ASTM SI 10 Standard for Use of the InternationalSystem of Units (SI): The Moder

7、n Metric System33. Terminology3.1 Definitions of terms used in this specification shall be inaccordance with Terminology D883.3.2 lot, none production run or a uniform blend of two ormore production runs.3.3 Abbreviations are in accordance with TerminologyD1600. PCTFE is the abbreviation for polychl

8、orotrifluoroeth-ylene.4. Classification4.1 This specification covers four types of polychlorotrif-luoroethylene sheet and film:44.1.1 Type ITransparent film, with high and low moisturevapor transmission rate.4.1.2 Type IIDimensionally stable transparent sheet andfilm with low moisture vapor transmis

9、sion rate.4.1.3 Type IIIDimensionally stable transparent film withvery low moisture vapor transmission rate.4.1.4 Type IVLow crystalline transparent film with highductility and extremely low moisture vapor transmission.4.2 A one-line system may be used to specify materialscovered by this specificati

10、on. The system uses predefined cellsto refer to specific aspects of this specification, as illustratedbelow.SpecificationStandard NumberBlock:Type:Grade:Class:SpecialNotes:- - - - -Example: Specification D3595 02, I 6 CFor this example, the line callout would be SpecificationD3595 02, I6C, and would

11、 specify a coagulated dispersionform of polytetrafluoro-ethylene that has all of the propertieslisted for that Type, Grade, and Class in the appropriate1This specification is under the jurisdiction of ASTM Committee D20 onPlastics and is the direct responsibility of Subcommittee D20.15 on Thermoplas

12、ticMaterials.Current edition approved March 1, 2014. Published March 2014. Originallyapproved in 1977. Last previous edition approved in 2007 as D3595 - 02(2007).DOI: 10.1520/D3595-14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm

13、.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from ASTM International, 100 Barr Harbor Drive, WestConshohocken, PA 194282959.4The basic polymer used to make these types of polymer does not correspond tothe types

14、given in Specification D1430.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1specified properties, tables, or both, in the specification iden-tified. A comma is used as

15、the separator between the StandardNumber and the Type. Separators are not needed between theType, Grade, and Class.5Provision for Special Notes isincluded so that other information can be provided whenrequired. An example would be in Specification D3295 81awhere dimensions and tolerances are specifi

16、ed for each AWGsize within Type and Class. When Special Notes are used, theyshould be preceded by a comma.5. Requirements5.1 The sheet and film shall be manufactured from poly-chlorotrifluoroethylene (PCTFE) plastics that consist of at least90 % chlorotrifluoroethylene. The remaining 10 % may in-clu

17、de chemical modifications, such as co-monomers, but notcolorants, fillers, plasticizers, or mechanical blends of otherresins.5.2 The length, width, roll core diameter, and maximumnumber of splices permitted shall be as agreed upon betweenthe purchaser and the seller. The tolerance for roll width sha

18、llbe 3 mm (18 in.). The tolerance for roll length shall be 6 10 %of the specified length.5.3 Thickness tolerances shall be as specified in Table 1.5.4 The sheet and film shall conform to the property valuesspecified in Table 2, Table 3, and Table 4.5.5 The material shall be essentially free fromcont

19、amination, wrinkles, holes, scratches, and other imperfec-tions unless otherwise agreed upon between the purchaser andthe seller.6. Sampling6.1 Sampling shall be statistically adequate to satisfy therequirements of 10.4.7. Number of Tests7.1 One set of test specimens as prescribed in Section 8shall

20、be considered sufficient for testing each batch. Theaverage result of the specimens tested shall conform to therequirements of this specification.8. Specimen Preparation8.1 ConditioningFor those tests where conditioning isrequired, condition the test specimens in accordance withProcedure A of Practi

21、ce D618 for a period of at least 24 h priorto test.8.2 Test ConditionsUnless otherwise specified, conducttests at the Standard Laboratory Temperature of 23 6 2C (70to 77F) and at 50 6 10 % relative humidity.8.3 Preparation of SpecimensTake test specimens acrossthe width of the roll.9. Test Methods9.

22、1 ThicknessMeasure the sample across the web width at25-mm (1-in.) increments. All readings shall be within thespecified tolerances. Abnormal readings may occasionallyresult from spot imperfections. Discard such readings and takenew readings in the same area (excluding the defect).9.2 Tensile Streng

23、th and ElongationDetermine tensilestrength and elongation of the sheet or film in accordance withTest Methods D882, Method A. The specimen size shall be 25by 127 mm (1 by 5 in.). Elongation rate shall be 508 mm (20in.)/min. Separation between jaws shall be 51 mm (2 in.).Edges of the specimen shall b

24、e parallel within 2 % of thewidth.5See the ASTM Form and Style Manual. Available from ASTM Headquarters.TABLE 1 Thickness ToleranceThicknessTolerance, % Type Availabilitymm in.0.015 0.0006 20 IV0.019 0.00075 20 III0.020 0.0008 20 IV0.0216 0.00085 20 IV0.023 0.0009 20 IV0.038 0.0015 20 I,0.051 0.002

25、15 I, II, III, IV0.064 0.0025 20 IV0.076 0.003 15 II0.102 0.004 15 II0.127 0.005 15 II0.140 0.0055 15 IV0.152 0.006 15 IV0.19 0.0075 10 II0.20 0.0078 10 III0.25 0.010 10 IITABLE 2 Tensile Strength and ElongationThickness, mm (in.) TypeTensile Strength, minElongation,min, %psi MPa0.019 to 0.0075 I, I

26、I, III 2800 19.32 50(0.00075 to 0.0015)0.051 to 0.002 I, II, III 3100 21.40 50(0.020 to 0.01)0.015 to 0.191 IV 4000 27.60 70(0.0006 to 0.0075)TABLE 3 Dimensional StabilityThickness, mm (in.) Type Shrinkage,Amax,%0.038 to 0.051 I 150.0015 to 0.0020.019 to 0.051 II, III 80.00075 to 0.0020.051 to 0.250

27、 III 50.002 to 0.010 II, III 50.015 to 0.191 IV 15(0.0006 to 0.002)APositive sign means increase in length.TABLE 4 Moisture Vapor Transmission RateThicknessTypeMoisture VaporTransmission Rate,max, g/m224hmm in.0.038 0.0015 I 0.610.191 0.0075 II 0.070.0051 0.0002 III 0.140.016 0.0006 IV 0.480.051 0.0

28、02 IV 0.16D3595 1429.3 Dimensional StabilityTest dimensional stability of thesheet or film in accordance with Test Method D1204 afterexposure to 149C (300F) for 10 min.9.4 Moisture Vapor Transmission RateMeasure the mois-ture vapor transmission rate in accordance with Test MethodF1249 at 100 % relat

29、ive humidity at 38C (100F).10. Inspection and Certification10.1 Inspection and certification of the material suppliedwith reference to a specification based on this specificationshall be for conformance to the requirements specified herein.10.2 Lot-acceptance shall be the basis on which acceptanceor

30、 rejection of the lot is made. The lot acceptance inspectionshall consist of thickness measurement.10.3 Periodic check inspection with reference to this speci-fication shall consist of the test for all requirements of thematerial in accordance with this specification.10.4 Certification shall be that

31、 the material was manufac-tured by a process in statistical control, sampled, tested, andinspected in accordance with this specification, and that theaverage values for the lot meet the requirements of thisspecification.10.5 A report of test results shall be furnished when re-quested. The report sha

32、ll consist of results of the lot-acceptanceinspection for the shipment and the results of the most recentperiodic-check inspection.11. Packaging and Package Marking11.1 PackagingThe material shall be packaged in stan-dard commercial containers so constructed as to ensure accep-tance by common or oth

33、er carriers for safe transportation at thelowest rate to the point of delivery, unless otherwise specifiedin the contract or order.11.2 MarkingShipping containers shall be marked withthe name of the material, type, size, and quantity containedtherein. Each roll of tape shall be marked to designate t

34、ype,grade, and lot number. The marking will be in the core and onthe pallet.11.3 All packing, packaging, and marking provisions ofPractice D3892 shall apply to this specification.12. Keywords12.1 chlorofluorocarbon plastics; copolymer; extrudedPCTFE; fluorocarbon polymer; fluoropolymers; homopolymer

35、;PCTFE; PCTFE film; PCTFE sheet; polychlorotrifluoroethyl-eneSUMMARY OF CHANGESCommittee D20 has identified the location of selected changes to this standard since the last issue(D3595 - 02(2007) that may impact the use of this standard. (March 1, 2014)(1) Modified Tables 1-4 to reflect correct conv

36、ersion values.(2) Changed the humidity tolerance in 8.2 from 65% to610 %.(3) Removed “%” from 5.2.(4) Removed Test Method D374 from 2.1 since it is a with-drawn standard.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin

37、 this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and mus

38、t be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the

39、responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700

40、, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D3595 143