ASTM D3209-1993(2008) Standard Test Method for Freeze Thaw Resistance of Polymer Floor Polishes《液态水乳化地板擦亮剂的耐冻结 融化的标准试验方法》.pdf

《ASTM D3209-1993(2008) Standard Test Method for Freeze Thaw Resistance of Polymer Floor Polishes《液态水乳化地板擦亮剂的耐冻结 融化的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM D3209-1993(2008) Standard Test Method for Freeze Thaw Resistance of Polymer Floor Polishes《液态水乳化地板擦亮剂的耐冻结 融化的标准试验方法》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 3209 93 (Reapproved 2008)Standard Test Method forFreeze/Thaw Resistance of Polymer Floor Polishes1This standard is issued under the fixed designation D 3209; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year o

2、f last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of the stabil-ity of polymer emulsion floor polishes when these are expos

3、edto repeated cycles of freezing and thawing. Possible degrada-tion of the emulsion is observed and possible reduction ofinitial gloss is measured.1.2 This standard does not purport to address all of thesafety problems, if any, associated with its use. It is theresponsibility of the user of this sta

4、ndard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D 1455 Test Method for 60 Specular Gloss of EmulsionFloor Polish3. Significance and Use3.1 This test method is used to determ

5、ine the effect offreezing on floor polishes. It may be used to predict thestability of a floor polish when exposed to freezing.4. Apparatus4.1 Freezer, adjusted to 7.8 to 6.7C (18 to 20F).4.2 Flint Glass Bottles, three, 4 oz (125 mL) capacity.34.3 Black Glass,4standard, polished as described in Test

6、Method D 1455.4.4 60 Gloss Meter.4.5 Polishes to be tested.5. Procedure5.1 Determine the turbidity of each polish, visually or byany other suitable method.5.2 Pour one coat of each polish to be tested on the blackglass. Allow to dry in a vertical position at room temperature.Determine the initial gl

7、oss in accordance with Test MethodD 1455.5.3 Place 100 mL of polish in each of three 125-mL (4-oz)flint glass bottles. Place the filled bottles side by side, horizon-tally, in the freezer on a rack, providing a minimum of 25 mm(1 in.) between the bottles and the freezer walls with thecontact area be

8、tween the bottles and the rack no greater thanthat required to support the bottles.5.4 Allow the samples to remain in the freezer for 16 h, ora minimum of 8 h after becoming solid.5.5 Remove all the samples of frozen polish and allow tothaw, undisturbed, at 18 to 24C (65 to 76F) for a period of 24h.

9、5.6 Inspect all thawed samples visually. Observe and recordany separation, stratification, or coagulation.5.7 Determine the turbidity on the open sample of polish asin 5.1.5.8 Agitate one bottle of thawed polish and apply one coatof polish to the standard black glass as in 5.2. Determine glossas in

10、5.2.5.9 Return the remaining two bottles of polish to the freezerfor 16 h, and repeat 5.4-5.8 for the second freeze/thaw cycle.5.10 Return the third bottle of polish to the freezer for 16 hand again repeat 5.4-5.8.1This test method is under the jurisdiction ofASTM Committee D21 on Polishesand is the

11、 direct responsibility of Subcommittee D21.03 on Chemical and PhysicalTesting.Current edition approved March 1, 2008. Published April 2008. Originallyapproved in 1973. Last previous edition approved in 2004 as D 3209 93 (2004).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orc

12、ontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The sole source of supply of the apparatus known to the committee at this timeis Fisher Scientific, Catalog No. 02-883 BA. If you are

13、 aware of alternativesuppliers, please provide this information to ASTM International Headquarters.Your comments will receive careful consideration at a meeting of the responsibletechnical committee,1which you may attend.4The sole source of supply of the apparatus known to the committee at this time

14、is Peril Stein Glass, 2543 Kensington Ave., Phila. PA 19125. If you are aware ofalternative suppliers, please provide this information to ASTM InternationalHeadquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee,1which you may attend.1Copyrig

15、ht ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.6. Interpretation of Results6.1 The polish passes each freeze/thaw cycle if there hasbeen no apparent change in appearance and no significant lossin gloss or increase in turbidity.7. Report7.1

16、Report test results as the number of cycles passedtogether with visual inspection comments regarding possibleseparation, stratification, or coagulation.8. Precision and Bias8.1 The test method differentiates polishes that are freezestable from those which are not. Polishes that are borderline infree

17、ze/thaw stability may pass in some laboratories and fail inothers.8.2 BiasSince there is no accepted reference materialsuitable for determining the bias for the procedure in TestMethod D 3209 for measuring freeze/thaw resistance of poly-mer emulsion floor polishes, bias has not been determined.9. Ke

18、ywords9.1 emulsion; polishes; polymerASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the ri

19、skof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of th

20、is standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake

21、 your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D 3209 93 (2008)2