ASTM D3061-1997(2003) Standard Guide for Three-Piece Steel and Tinplate Straight-Wall and Necked-In Aerosol Cans《三铰钢和马口铁制直壁和边缘向内弯曲的气溶胶罐标准导则》.pdf

《ASTM D3061-1997(2003) Standard Guide for Three-Piece Steel and Tinplate Straight-Wall and Necked-In Aerosol Cans《三铰钢和马口铁制直壁和边缘向内弯曲的气溶胶罐标准导则》.pdf》由会员分享，可在线阅读，更多相关《ASTM D3061-1997(2003) Standard Guide for Three-Piece Steel and Tinplate Straight-Wall and Necked-In Aerosol Cans《三铰钢和马口铁制直壁和边缘向内弯曲的气溶胶罐标准导则》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 3061 97 (Reapproved 2003)Standard Guide forThree-Piece Steel and Tinplate Straight-Wall and Necked-InAerosol Cans1This standard is issued under the fixed designation D 3061; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revi

2、sion, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 In the interest of

3、 uniformity and quality, the aerosolindustry has developed dimensional guidelines which aresuggested for U.S. three-piece steel and tin-plate aerosol cansof straight-wall and necked-in design. Domestic can makersuniformly agreed to comply with these guidelines and wereinstrumental in their developme

4、nt. A series of standard meth-ods and gages were also developed to uniformly determinespecific dimensions. The tolerances established for these di-mensions allow for can manufacturing and filling processvariations.1.2 It is the purpose of this guide to provide a listing ofcurrently manufactured aero

5、sol can sizes as well as industryvoluntary dimensional guidelines.1.3 Table 1 and Table 2 present the sales code diameter andheight of straight-wall and necked-in three-piece aerosol cans.The units in parentheses are in SI format, an alternate referenceusing dimensions suggested by the Metric Workin

6、g Group ofthe Can Makers Institute. They are based on InternationalOrganization for Standardization (ISO) inside diameters to thenearest whole millimetre. Can heights are based on heightsover the double seam (CSMA Dimension D) converted to thenearest whole millimetre.2. Terminology2.1 Specific dimen

7、sions used in this guide are described asfollows and correspond to those associated with the cross-sectional drawings of straight-wall and necked-in aerosol cans(Fig. 1 and Fig. 2, respectively).2.2 Dimensions and Definitions:2.2.1 Ainside diameter of the 1-in. (25.4-mm) opening.2.2.2 Boutside diame

8、ter of the 1-in. (25.4-mm) opening.2.2.3 Cdistance from the top of the curl of the 1-in.(25.4-mm) opening to the top of the top double seam.2.2.4 Ddistance from the top of the top double seam to thebottom of the bottom double seam.2.2.5 Edistance from the top of the curl of the 1-in.(25.4-mm) openin

9、g to the bottom of the bottom double seam.2.2.6 Fdistance between the bottom of the top doubleseam and the top of the bottom double seam.2.2.7 Gcurl thickness of the 1-in. (25.4-mm) openingmeasured using the special Starrett micrometer or equivalent.2.2.8 J*vertical distance from the maximum snap-lo

10、ckdiameter to the bottom of the countersink.2.2.9 Koutside diameter of the top double seam (exclud-ing crossover).2.2.10 L*width of the countersink at the maximum snap-lock diameter.2.2.11 M*snap-lock undertuck.2.2.12 N*outside diameter of the snap-lock.2.2.13 P*snap-lock wall length, as measured ve

11、rticallyfrom the maximum snap-lock diameter to the point of maxi-mum undertuck.1This specification is under the jurisdiction of ASTM Committee D10 onPackaging and is the direct responsibility of Subcommittee D10.33 on MechanicalDispensers. Originally developed by the Chemical Specialties Manufacture

12、rs Assn.(CSMA).Current edition approved Sept. 10, 1997. Published April 1998. Originallypublished as D 3061 72. Last previous edition D 3061 79 (1991).TABLE 1 Sales Code Height for Various Diameters ofStraight-Wall Aerosol Cans (SI)202 (52 mm) by 207.5 (60 mm) by 211 (65 mm) by 300 (73 mm) by214 ( 7

13、3) 509 (141) 413 (122) 709 (192)306 ( 85) 605 (160) 600 (152)314 ( 98) 701 (179) 604 (158)406 (111) 703 (182) 612 (171)505 (134) 708 (190) 713 (198)509 (141) 713 (198) 908 (241)700 (177)708 (190)TABLE 2 Sales Code Height for Various Diameters of Necked-InAerosol Cans (SI)111/112 by(45 mm)200/202 by(

14、52 mm)202/205 by(57 mm)207.5/211 by(65 mm)211/214 by(70 mm)214 ( 73) 214 ( 73) 410 (117) 413 (122) 315 (100)312 ( 95) 314 ( 98) 604 (158) 604 (158) 413 (122)410 (117) 406 (111) 608 (165) 612 (171) 714 (200)508 (139) 509 (141) 701 (179) 713 (198) 804 (209)608 (165) 514 (149) 704 (184) 1006 (263)700 (

15、177) 710 (193)708 (190) 802 (206)803 (207)1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.2.2.14 Svertical distance, tangent to the outside diameterof the dome double seam, from the top of the dome doubleseam to the necked-in area of

16、 the can sidewall.2.2.15 Twidth or height of the top double seam.2.2.16 V*body outside diameter of necked-in cans.2.2.17 Wtop neck angle of the body wall.NOTE 1* Method of measurement to be agreed upon between thesupplier and the user if needed.3. Guideline Dimensions3.1 The following tables provide

17、 guideline dimensions forstraight-wall and necked-in three-piece aerosol cans (alternatetables furnish SI equivalents).3.2 Various container heights (D, E, and F) are based on thefollowing examples:3.2.1 A typical 211 by 413 aerosol can has a Sales Codeheight of 413, or 41316 in., which converted to

18、 its decimalequivalent, is 4.812 in However, Dimension D is derived bysubtracting 0.020 in. from the decimal conversion of the SalesCode height:D 5 4.812 in. 2 0.020 in. 5 4.792 in. (1)3.2.2 Dimension E is obtained by adding the C Dimensionto the D Dimension. The C Dimension is found in Tables 3-6,d

19、epending on end diameter and unit of measure.E 5 C 1 D 5 0.798 in. 1 4.792 in. 5 5.590 in. (2)3.2.3 Dimension F is the Sales Code height decimal equiva-lent minus 0.300 in This conversion includes the double seamwidth or height of both top and bottom double seams, as wellas, the 0.020-in. height red

20、uction from our D Dimensiondetermination.F 5 4.812 in. 2 0.300 in. 5 4.512 in. (3)3.3 In all tables, the guidelines refer to Fig. 1 and Fig. 2,which illustrate the dimensions. Table 3 and Table 4 givestraight-wall aerosol can height and curl dimensions. Table 5and Table 6 give comparable information

21、 for necked-in aerosolcans.4. Overcap Fit Dimensions4.1 Table 7 provides the dimensions of top end and bodywhich are critical for overcap fit.5. Keywords5.1 aerosol cans; specifications for tin-plate aerosol cans;tin-plate aerosol cansFIG. 1 Straight-Wall Aerosol CanFIG. 2 Necked-In Aerosol CanD 306

22、1 97 (2003)2TABLE 3 Straight-Wall Aerosol Cans Guideline Dimensions (Inches)Nominal Can SizeA60.004B60.010C60.016D60.031E60.035F(minimum)G60.007202 by 214 1.000 1.221 0.396 2.855 3.251 2.575 0.130202 by 306 1.000 1.221 0.396 3.355 3.751 3.075 0.130202 by 314 1.000 1.221 0.396 3.855 4.251 3.575 0.130

23、202 by 406 1.000 1.221 0.396 4.355 4.751 4.075 0.130202 by 505 1.000 1.221 0.396 5.293 5.689 5.013 0.130202 by 509 1.000 1.221 0.396 5.542 5.938 5.262 0.130202 by 700 1.000 1.221 0.396 6.980 7.376 6.700 0.130202 by 709 1.000 1.221 0.396 7.480 7.876 7.200 0.130207.5 by 509 1.000 1.221 0.798 5.542 6.3

24、41 5.262 0.130207.5 by 605 1.000 1.221 0.798 6.292 7.090 6.012 0.130207.5 by 701 1.000 1.221 0.798 7.042 7.840 6.676 0.130207.5 by 703 1.000 1.221 0.798 7.168 7.966 6.888 0.130207.5 by 708 1.000 1.221 0.798 7.480 8.278 7.200 0.130207.5 by 713 1.000 1.221 0.798 7.792 8.590 7.512 0.130211 by 413 1.000

25、 1.221 0.798 4.792 5.590 4.512 0.130211 by 600 1.000 1.221 0.798 5.980 6.778 5.700 0.130211 by 604 1.000 1.221 0.798 6.230 7.028 5.950 0.130211 by 612 1.000 1.221 0.798 6.730 7.528 6.450 0.130211 by 713 1.000 1.221 0.798 7.792 8.590 7.512 0.130211 by 908 1.000 1.221 0.798 9.480 10.278 9.200 0.130300

26、 by 709 1.000 1.221 0.798 7.542 8.340 7.262 0.130TABLE 4 Straight-Wall Aerosol Cans Guideline Dimensions (Millimetres)Nominal Can SizeA60.10B60.25C60.41D60.79E60.89F(minimum)G60.1852 by 73 25.40 31.01 9.40 72.52 82.58 65.41 3.3052 by 85 25.40 31.01 9.40 85.22 95.28 78.11 3.3052 by 98 25.40 31.01 9.4

27、0 97.92 107.98 90.81 3.3052 by 111 25.40 31.01 9.40 110.62 120.68 103.51 3.3052 by 134 25.40 31.01 9.40 134.43 144.49 127.32 3.3052 by 141 25.40 31.01 9.40 140.78 150.84 133.67 3.3052 by 177 25.40 31.01 9.40 177.29 187.35 170.18 3.3052 by 190 25.40 31.01 9.40 189.99 200.05 182.88 3.3060 by 141 25.40

28、 31.01 20.27 140.78 161.05 133.67 3.3060 by 160 25.40 31.01 20.27 159.83 180.10 152.72 3.3060 by 179 25.40 31.01 20.27 178.88 199.15 171.77 3.3060 by 182 25.40 31.01 20.27 182.05 202.32 174.94 3.3060 by 190 25.40 31.01 20.27 189.99 210.26 182.88 3.3060 by 198 25.40 31.01 20.27 197.93 218.20 190.82 3

29、.3065 by 122 25.40 31.01 20.27 121.72 141.99 114.62 3.3065 by 152 25.40 31.01 20.27 151.89 172.16 144.62 3.3065 by 158 25.40 31.01 20.27 158.24 178.51 151.13 3.3065 by 171 25.40 31.01 20.27 170.94 191.21 163.83 3.3065 by 198 25.40 31.01 20.27 197.93 218.20 190.82 3.3065 by 241 25.40 31.01 20.27 240.

30、79 261.06 233.68 3.3073 by 192 25.40 31.01 20.27 191.58 211.85 184.47 3.30D 3061 97 (2003)3TABLE 5 Necked-In Aerosol Cans Guideline Dimensions(Inches)Nominal Can SizeA60.004B60.010C60.016D60.031E60.035F(minimum)G60.007111/112 by214A1.000 1.221 0.225 2.855 3.080 2.575 0.130314A1.000 1.221 0.225 3.855

31、 4.080 3.575 0.130410A1.000 1.221 0.225 4.604 4.830 4.325 0.130508A1.000 1.221 0.225 5.480 5.705 5.200 0.130608A1.000 1.221 0.225 6.480 6.705 6.200 0.130200/202 by214 1.000 1.221 0.370 2.855 3.225 2.575 0.130314A1.000 1.221 0.370 3.855 4.225 3.575 0.130406A1.000 1.221 0.370 4.355 4.725 4.075 0.13050

32、9A1.000 1.221 0.370 5.542 5.912 5.262 0.130514A1.000 1.221 0.370 5.855 6.225 5.575 0.130700A1.000 1.221 0.370 6.980 7.350 6.700 0.130708 1.000 1.221 0.370 7.480 7.850 7.200 0.130202/205 by410 1.000 1.221 0.396 4.605 5.001 4.325 0.130604A1.000 1.221 0.396 6.230 6.626 5.948 0.130608 1.000 1.221 0.396

33、6.480 6.876 6.200 0.130701 1.000 1.221 0.396 7.043 7.439 6.763 0.130704 1.000 1.221 0.396 7.230 7.626 6.948 0.130710 1.000 1.221 0.396 7.605 8.003 7.325 0.130802 1.000 1.221 0.396 8.105 8.501 7.825 0.130803 1.000 1.221 0.396 8.168 8.564 7.888 0.130207.5/211 by413A1.000 1.221 0.798 4.792 5.590 4.512

34、0.130604A1.000 1.221 0.798 6.230 7.028 5.950 0.130612 1.000 1.221 0.798 6.730 7.528 6.450 0.130713A1.000 1.221 0.798 6.792 8.590 7.512 0.130211/214 by315 1.000 1.221 0.798 3.918 4.716 3.638 0.130413 1.000 1.221 0.798 4.792 5.590 4.512 0.130714 1.000 1.221 0.798 7.855 8.653 7.575 0.130804 1.000 1.221

35、 0.798 8.230 9.028 7.950 0.1301006 1.000 1.221 0.798 10.355 11.153 10.075 0.130ANot all suppliers manufacture cans with D, E, and F dimensions in the indicated sizes to conform to the Sales Code height formula. Purchasers should work with theirsupplier(s) to determine suitable D, E, and F dimensions

36、 for their operations.D 3061 97 (2003)4TABLE 6 Necked-In Aerosol Cans Guideline Dimensions(Millimetres)Nominal Can SizeA60.10B60.25C60.41D60.94E61.04F(minimum)G60.1845 mm by73A25.40 31.01 5.72 72.56 78.23 65.41 3.3098A25.40 31.01 5.72 97.92 103.63 90.81 3.30117A25.40 31.01 5.72 116.97 122.68 109.86

37、3.30139A25.40 31.01 5.72 139.19 144.91 132.08 3.30165A25.40 31.01 5.72 164.59 170.31 157.48 3.3052 mm by73 25.40 31.01 10.06 72.52 82.58 65.41 3.3098A25.40 31.01 10.06 97.92 107.98 90.81 3.30111A25.40 31.01 10.06 110.62 120.68 103.51 3.30141A25.40 31.01 10.06 140.78 150.84 133.67 3.30149A25.40 31.01

38、 10.06 148.72 158.78 141.61 3.30177A25.40 31.01 10.06 177.29 187.35 170.18 3.30190 25.40 31.01 10.06 189.99 200.05 182.88 3.3057 mm by117 25.40 31.01 10.06 116.97 127.03 109.86 3.30158A25.40 31.01 10.06 158.24 168.30 151.13 3.30165 25.40 31.01 10.06 164.59 174.65 157.48 3.30179 25.40 31.01 10.06 178

39、.88 188.94 171.77 3.30184 25.40 31.01 10.06 183.64 193.70 176.53 3.30193 25.40 31.01 10.06 193.17 203.23 186.06 3.30206 25.40 31.01 10.06 205.87 215.93 198.76 3.30207 25.40 31.01 10.06 207.45 217.51 200.34 3.3065 mm by122A25.40 31.01 20.27 121.72 141.99 114.62 3.30158A25.40 31.01 20.27 158.24 178.51

40、 151.13 3.30171 25.40 31.01 20.27 170.94 191.21 163.83 3.30198A25.40 31.01 20.27 197.93 218.20 190.82 3.3070 mm by100 25.40 31.01 20.27 99.50 119.77 92.39 3.30122 25.40 31.01 20.27 121.73 142.00 114.62 3.30200 25.40 31.01 20.27 199.52 219.79 192.41 3.30209 25.40 31.01 20.27 209.04 229.31 201.93 3.30

41、263 25.40 31.01 20.27 263.02 283.29 255.91 3.30ANot all suppliers manufacture cans with D, E, and F dimensions in the indicated sizes to conform to the Sales Code height formula. Purchasers should work with theirsupplier(s) to determine suitable D, E, and F dimensions for their operations.D 3061 97

42、(2003)5ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such righ

43、ts, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional

44、standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM

45、Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the abovea

46、ddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 7 Straight-Wall and Necked-In Aerosol Can Guideline Dimensions for Overcap Fit Inches (Millimetres)Nominal CanDiameterSTRAIGHT-WALL AEROSOLSJAminimumKB60.010(0.25)LAmin

47、imumMAminimumNA60.004(0.10)PAminimumT60.010(0.25)202 0.100 2.182 0.100 0.003 1.788 0.050 0.128Y (52 mm) (2.54) (55.42) (2.54) (0.08) (45.42) (1.27) (3.25)207.5 0.135 2.487 0.100 0.003 2.085 0.040 0.128(60 mm) (3.43) (63.17) (2.54) (0.08) (52.96) (1.02) (3.25)211 0.135 2.700 0.100 0.003 2.303 0.040 0

48、.128(64 mm) (3.43) (68.58) (2.54) (0.08) (58.50) (1.02) (3.25)300 0.145 3.005 0.100 0.003 2.598 0.040 0.128(73 mm) (3.68) (76.33) (2.54) (0.08) (65.99) (1.02) (3.25)NECKED-IN AEROSOLSNominal Can DiameterKA60.010(0.25)SB60.012(0.30)T60.010(0.25)VA60.006(0.15)WA68111/112 1.715 0.210 0.125 1.770 35(45

49、mm) (43.56) (5.33) (3.18) (44.96)200/202 1.996 0.260 0.128 2.074 35(52 mm) (50.70) (6.60) (3.25) (52.68)202/205 2.182 0.260 0.128 2.273 35(57 mm) (55.42) (6.60) (3.25) (57.73)207.5/211 2.487 0.260 0.128 2.594 35(65 mm) (63.17) (6.60) (3.25) (65.89)211/214 2.700 0.260 0.128 2.762 35(70 mm) (68.58) (6.60) (3.25) (70.15)AMethod of measurement to be agreed upon between the supplier and the user if needed.BFor dot regular aerosol; dot specifications, 2P and 2Q may vary.D 3061 97 (2003)6