ASTM D3018 D3018M-2010 Standard Specification for Class A Asphalt Shingles Surfaced with Mineral Granules.pdf

《ASTM D3018 D3018M-2010 Standard Specification for Class A Asphalt Shingles Surfaced with Mineral Granules.pdf》由会员分享，可在线阅读，更多相关《ASTM D3018 D3018M-2010 Standard Specification for Class A Asphalt Shingles Surfaced with Mineral Granules.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D3018/D3018M 10Standard Specification forClass A Asphalt Shingles Surfaced with Mineral Granules1This standard is issued under the fixed designation D3018/D3018M; the number immediately following the designation indicates theyear of original adoption or, in the case of revision, the yea

2、r of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification covers granul

3、e-surfaced asphalt roof-ing shingles that meet the requirements for Class A fire test,behavior on heating, and wind testing.1.2 Shingles meeting this specification are intended to beapplied with a headlap of not less than 51 mm 2 in.1.3 The values stated in either SI units or inch-pound unitsare to

4、be regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.2. Referenced Documents2.1 ASTM Standards:2D228 Test M

5、ethods for Sampling, Testing, and Analysis ofAsphalt Roll Roofing, Cap Sheets, and Shingles Used inRoofing and WaterproofingD1079 Terminology Relating to Roofing and WaterproofingD3161 Test Method for Wind-Resistance of AsphaltShingles (Fan-Induced Method)E108 Test Methods for Fire Tests of Roof Cov

6、erings3. Terminology3.1 Definition:3.1.1 glass matfor testing purposes in accordance withTest Methods D228, glass mat shall be considered as felt.3.2 For definitions of terms used in this specification, seeTerminology D1079.4. Classification4.1 Asphalt shingles covered by this specification are of t

7、wotypes:4.1.1 Type ISelf-sealing.4.1.2 Type IINon-self-sealing.5. Materials and Manufacture5.1 The shingles covered by this specification shall consistof organic felt or glass mat(s) saturated or impregnated andcoated on both sides with a hot asphaltic material and com-pletely surfaced on the weathe

8、r side with mineral granulesembedded in the coating.5.2 The hot asphaltic material used to saturate or impregnateand coat the organic felt or glass mat(s) may be compoundedwith a mineral stabilizer.5.3 The reverse side of the shingles shall be covered with asuitable material to prevent the shingles

9、from sticking togetherin the package.5.4 Type I shingles shall have a factory-applied adhesivethat will seal the shingles together after application.6. Physical Requirements6.1 Shingles shall not stick together in the package so as tocause damage upon being unpacked at ambient temperaturesabove 10 C

10、 50F.6.2 Loss and Behavior on HeatingThere shall be not morethan 1.5 % average loss of volatile matter, and the granularsurfacing shall not slide more than 2 mm 116 in.6.3 Fire Test ClassificationShingles shall pass all of theClass A fire exposure tests.6.4 Wind ResistanceShingles shall pass Class A

11、 of thewind-resistance test (see 9.1.3).7. Dimensions and Permissible Variations7.1 The form and size of the shingles shall be as agreedupon by the purchaser and seller.7.2 The shingles shall not vary in length more than 63.2mm 18 in. from nominal dimensions established for each size,except that the

12、 length of shingles without cutouts shall not varymore than 66.4 mm 14 in. The width of the shingles shall notvary more than 66.4 mm 14 in.1This specification is under the jurisdiction of ASTM Committee D08 onRoofing and Waterproofing and is the direct responsibility of Subcommittee D08.02on Steep R

13、oofing Products and Assemblies.Current edition approved June 15, 2010. Published July 2010. Originallyapproved in 1972. Last previous edition approved in 2009 as D3018 09. DOI:10.1520/D3018_D3018M-10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Servic

14、e at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.8. Workmanship, Finish, and Appearance8.1 The

15、organic felt or glass mat(s) shall be uniformlysaturated or impregnated with asphalt and shall show nountreated spots at any point upon cutting 50-mm 2-in. widestrips at random across the entire width of the shingle andsplitting them open for their full length.8.2 The weather surface shall be unifor

16、m in finish and maybe embossed to simulate a grain texture. The mineral granulesshall cover the entire surface and shall be firmly embedded inthe asphalt coating. The granules shall not have ruptured thefibers of the felt or mat.8.3 The finished shingles shall be free of visible defectssuch as holes

17、, edges not cleanly cut, rents, cracks, indentations,or lumps of coating.9. Sampling and Test Methods9.1 Sample the material in accordance with Test MethodsD228 and determine conformance to the requirements of thisspecification in accordance with the following test methods:9.1.1 Loss and Behavior on

18、 HeatingTest Methods D228.9.1.2 Fire Test ClassificationTest Methods E108, Class ATests.9.1.3 Wind ResistanceTest Method D3161.10. Inspection10.1 Inspection of material shall be made as agreed upon bythe purchaser and the seller as part of the purchase contract.11. Rejection and Resubmittal11.1 Fail

19、ure to conform to any one of the requirementsprescribed in this specification shall constitute grounds forrejection. In case of rejection, the seller shall have the right toreinspect the rejected shipment and resubmit the lot afterremoval of those packages not conforming to the specifiedrequirement.

20、12. Packaging, Marking, and Shipping12.1 The shingles shall be packed for shipment to ensureacceptance by common carrier for interstate transportation andto afford adequate protection from normal hazards of handling.12.2 Each package shall be plainly marked with the nameand brand of the manufacturer

21、; the area of roof surface coveredper package; and the style, type, and color of the product.Directions for application shall be included in at least everysquare of shingles.13. Keywords13.1 asphalt shingles; Class A Shingles; granule-surfaceshingles; wind resistanceASTM International takes no posit

22、ion respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibilit

23、y.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM

24、 International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address s

25、hown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D3018/D3018M 102