ASTM D2977-2014 Standard Practice for Particle Size Range of Peat Materials for Horticultural Purposes《测定园艺用泥炭材料粒径范围的标准实施规程》.pdf

《ASTM D2977-2014 Standard Practice for Particle Size Range of Peat Materials for Horticultural Purposes《测定园艺用泥炭材料粒径范围的标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM D2977-2014 Standard Practice for Particle Size Range of Peat Materials for Horticultural Purposes《测定园艺用泥炭材料粒径范围的标准实施规程》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D2977 14Standard Practice forParticle Size Range of Peat Materials for HorticulturalPurposes1This standard is issued under the fixed designation D2977; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last r

2、evision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This practice covers measurement of the mass percent-age of fractions of a peat material defined in terms of selectedranges

3、 of screen sizes.1.2 UnitsThe values stated in SI units are being regardedas standard. Units of inch-pound are provided for informationonly.1.3 All measured and calculated values shall conform to theguidelines for significant digits and rounding established inPractice D6026.1.4 This standard does no

4、t purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standard

5、s:2D653 Terminology Relating to Soil, Rock, and ContainedFluidsD2974 Test Methods for Moisture, Ash, and Organic Matterof Peat and Other Organic SoilsD3740 Practice for Minimum Requirements for AgenciesEngaged in Testing and/or Inspection of Soil and Rock asUsed in Engineering Design and Constructio

6、nD4753 Guide for Evaluating, Selecting, and Specifying Bal-ances and Standard Masses for Use in Soil, Rock, andConstruction Materials TestingD6026 Practice for Using Significant Digits in GeotechnicalDataE11 Specification for Woven Wire Test Sieve Cloth and TestSieves3. Terminology3.1 Definitions:3.

7、1.1 For definitions of common technical terms in thispractice, refer to Terminology D653.4. Summary of Practice4.1 A representative test specimen of air-dried peat isseparated into four designated fractions by means of a 2.36 mm(No. 8) sieve and an 0.85 mm (No. 20) sieve. The fractions are:(1) forei

8、gn matter removed manually from the 2.36 mm (No. 8)sieve, (2) coarse fiber retained on the 2.36 mm (No. 8) sieve,(3) medium fiber through the 2.36 mm (No. 8) sieve butretained on the 0.85 mm (No. 20) sieve and fine fibers and finesthrough the 0.85 mm (No. 20) sieve. The mass percentage ofeach fracti

9、on is reported on the as-received basis.5. Significance and Use5.1 This practice separates peat material into arbitraryfractions based on particle size. Physical separation of peatmaterial according to particle size provides a useful indicatorof the properties of a peat specimen such as pore space,d

10、ecomposition, etc. It provides a means of determining theamount of foreign matter not in a divided state such as sticks,stones, and glass.NOTE 1The quality of the result produced by this standard isdependent on the competence of the personnel performing it, and thesuitability of the equipment and fa

11、cilities used. Agencies that meet thecriteria of Practice D3740 are generally considered capable of competentand objective testing/sampling/inspection/ and the like. Users of thisstandard are cautioned that compliance with Practice D3740 does not initself assure reliable results. Reliable results de

12、pend on many factors;Practice D3740 provides a means of evaluating some of those factors.6. Apparatus6.1 Mechanical Sieve Shaker.6.2 Sieves2.36 mm (No. 8) and 0.85 mm (No. 20) sievesequipped with cover and bottom pan.6.3 Balance or Scale, a balance or scale for determining themass of the soil having

13、 a minimum capacity of 500 g and1This practice is under the jurisdiction of ASTM Committee D18 on Soil andRock and is the direct responsibility of Subcommittee D18.22 on Soil as a Mediumfor Plant Growth.Current edition approved Nov. 1, 2014. Published November 2014. Originallyapproved in 1971. Last

14、previous edition approved in 2003 as D2977 03, which waswithdrawn February 2012 and reinstated in November 2014. DOI:10.1520/D2977-14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume info

15、rmation, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1meeting the requirements of Standard D4753 for a

16、 balance orscale of 0.01 g readability.7. Preparation of Sample7.1 Air-dry sample in accordance with Method B of TestMethods D2974, and record the mass percentage of moistureremoved by air-drying. Information on obtaining a representa-tive sample is covered in Test Methods D2974.8. Procedure8.1 Mix

17、the air-dried sample thoroughly and place anapproximately 20-g specimen on the 2.36 mm (No. 8) sieve.Secure the 2.36 mm (No. 8) and 0.85 mm (No. 20) sievesequipped with cover and bottom pan and shake at a suitablespeed for 10 min. Remove foreign matter from the 2.36 mm(No. 8) sieve and determine the

18、 mass. Designate this fraction asforeign matter. Determine the mass of the remaining fractionretained on the 2.36 mm (No. 8) sieve and designate thisfraction as coarse fiber. Determine the mass of the fractionretained on the 0.85 mm (No. 20) sieve and designate thisfraction as medium fiber. Determin

19、e the mass of the fractionfound in the bottom pan and designate this fraction as fines.9. Calculation9.1 Convert the specimen mass and fraction mass to theas-received basis in accordance with Method B of Test Meth-ods D2974.NOTE 2If foreign matter is absent, conversion to the as-received basisis not

20、 necessary.10. Report: Test Data Sheet(s)/Form(s)10.1 Record as a minimum the following general informa-tion:10.1.1 Sample/specimen identifying information, such asProject No., Boring No., Sample No., Depth, etc.10.1.2 Any special selection and preparation process, suchas removal of gravel or other

21、materials.10.1.3 Technician name/initials, method used and date.10.2 Record as a minimum the following test information:10.2.1 Foreign matter = fraction removed from 2.36 mm(No. 8) sieve10.2.2 Coarse fiber = fraction retained on 2.36 mm (No. 8)sieve10.2.3 Medium fiber = fraction retained on 0.85 mm

22、(No.20) sieve10.2.4 Fine fibers and fines = fraction through 0.85 mm(No. 20) sieve (in pan)11. Keywords11.1 particle size; peat; sievingSUMMARY OF CHANGESIn accordance with Committee D18 policy, this section identifies the location of changes to this standard sincethe last edition (03) that may impa

23、ct the use of this standard.(1) Standard D6026 was added to the Referenced DocumentsSection.(2) Typos were corrected.(3) Subcommittee designated as responsible for this standardwas updated.(4) Units statement added to the Scope.(5) Test method was changed to a practice.(6) Precision and Bias stateme

24、nt was removed until uniformsamples can be prepared and an inter-laboratory study can beperformed.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determ

25、ination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or w

26、ithdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that

27、your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (s

28、ingle or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 142